Model VM08 Owner’s Manual

Channel Parameter Edit Mode

Twelve items, as shown in list below, can be set by the channel parameter edit mode. Regard- less of the VM08’s current mode, their respective edit modes can be entered by executing the key operations listed below. To exit from the channel parameter edit mode, press the EXIT key.

Setting Item

Executing Key

Changing the channel

Changing the setup content

 

 

 

 

Setup of PAN (sound image)

When the PAN/EQ key is repeat-

 

 

Setup of LO-EQ

edly pressed, the setup item will

 

 

alternately switch. In the initial

 

 

 

 

 

Setup of MID-EQ

 

 

state, the channel 1 PAN setup will

 

 

 

 

 

 

be displayed.

 

 

Setup of HI-EQ

Channel 1 is selected in

 

 

 

 

 

the initial state and the

 

Level setup of EFF SEND 1

When the EFF/AUX key is repeat-

 

channel to be edited is se-

 

 

Setup is changed by utilizing

Level setup of EFF SEND 2

edly pressed, the setup item will

lected by pressing each re-

the DATA encoder.

 

alternately switch. In the initial

spective CH ON/CH SEL

Level setup of AUX SEND 1

 

state, the channel 1 EFF SEND 1

key. The CH ON/CH SEL

 

 

 

Level setup of AUX SEND 2

level setup will be displayed.

key LED (green) of the se-

 

 

 

lected channel will blink.

 

PRE/POST setup of EFF SEND 1

If the EFF/AUX key is pressed

 

 

 

 

while pressing on the EXIT key, the

 

 

PRE/POST setup of EFF SEND 2

 

 

setup item will alternately switch.

 

 

 

 

 

PRE/POST setup of AUX SEND 1

In the initial state, the display will

 

 

be PRE/POST setup of channel 1

 

 

 

 

 

PRE/POST setup of AUX SEND 2

 

 

EFF SEND 1.

 

 

<Useful Information!>

When selecting a desired item, each time the respective key is pressed, it will move to the next item, and if the key is held down, it will change one item backward in the setup item list.

Setup method for PAN setting

Balance of channels 1 ~ 4, 5/6, 7/8 and STEREO MASTER signals must be setup.

1.Press the PAN/EQ key to light up the [PAN] dot in the status display section.

The LCD will display the following:

* Character display section:

[1-Pan: C] will be displayed. Now PAN of channel 1 can be setup, and this indicates that the present PAN setting is for centering the sound image (C).

3.The number is adjusted with the DATA encoder.

The number can be changed within the range of [L10] ~ [C] ~ [R10] and the sound image position will change accordingly. The graphic display will also change at the same time.

[L10] ~ [L1] ~ [C] ~ [R1] ~ [R10] will be displayed.

The digit moves up and down.

Blinking

Lit

2.Press the desired CH ON/CH SEL key and select the channel to be adjusted.

CH ON/CH SEL key of the selected channel will blink.

<Useful information!>

When the DATA encoder is activated to set PAN, its position will be displayed digitally in 21 steps within the range of [L10] ~ [C] ~ [R10] but the actual change in sound will be continuous (smooth). If channels 5/6 and 7/8 had been se- lected, balance between the two channels can be setup. If the MASTER had been selected, bal- ance between L and R can be setup.

14

Page 14
Image 14
Fostex VM08 Channel Parameter Edit Mode, Setup method for PAN setting, Number is adjusted with the Data encoder