Fostex VM08 owner manual Doubling effect parameters parameter type Doubling

Model VM08 Owner’s Manual

Doubling effect parameters (parameter type: DOUBLING)

For effect type 34 of the preceding "Effect type" table, the following three parameters can be adjusted.

1. Lch DELAY TIME	Adjust the delay time of the L channel. Range: 0.1--9.9 ms (99 steps in 0.1 ms units), 10-
	-99 ms (90 steps in 1 ms units), 100--200 ms (51 steps in 2 ms units)
	*	The ENTER key / foot switch cannot be used for tap input.
2. Rch DELAY TIME	Adjust the delay time of the R channel. Range: 0.1--9.9 ms (99 steps in 0.1 ms units), 10-
	-99ms(90 steps in 1 ms units), 100--200 ms (51 steps in 2 ms units)
	*	The ENTER key / foot switch cannot be used for tap input.
3. FILTER	Adjust the tone of the delay sound. Range: L9~L1, -, H1~H9
	*	[-]is Filter Off
	*	L1~L9 = LPF (larger numbers will lower the cutoff frequency)
	*	H1~H9 = HPF (larger numbers will raise the cutoff frequency)

Chorus effect parameters (parameter type: CHORUS)

For effect type 35 of the preceding "Effect type" table, the following four parameters can be adjusted.

1. DEPTH	Adjust the chorus depth. Range: 0--99(100 steps in increments of 1)
2. DOUBLING TIME	Adjust the time difference of the doubling effect. Range: 0--99(100 steps in increments
	of 1)
3. DOUBLING BALANCE	Adjust the volume of the doubling effect. Range: 0--99(100 steps in increments of 1)
4. FILTER	Adjust the tone of the delay sound. Range: L9~L1, -, H1~H9
	* [-]is Filter Off
	* L1~L9 = LPF (larger numbers will lower the cutoff frequency)
	* H1~H9 = HPF (larger numbers will raise the cutoff frequency)

Flanger effect parameters (parameter type: FLANGE)

For effect type 36 of the preceding "Effect type" table, the following four parameters can be adjusted.

1. RATE	Adjust the speed of modulation. Range: 0.1--2.0 Hz	(200 steps in 0.01 Hz units)
2. DEPTH	Adjust the depth of modulation. Range: 0--99(100 steps in increments of 1)
3. MOD DELAY	Adjust the modulation delay. Range: 0--200(201 steps in increments of 1)
4. FEEDBACK	Adjust the number of modulation repeats. Range:	0--99(100 steps in increments of 1)

Delay pitch effect parameters (parameter type: DELAY PITCH)

For effect type 38 of the preceding "Effect type" table, the following four parameters can be adjusted.

1. PITCH	Adjust the amount of pitch shift. Range: -24--0--+24(49 steps in semitone units)
	* +/-12is one octave. +/-24is two octaves.
2. ADJUST	Make fine adjustments to the amount of pitch shift. Range: -50--0--+50(101 steps in
	increments of 1)
	* +50 is a semitone sharp. -50is a semitone flat.
3. DLY TIME	Adjust the delay time until the pitch-shifted sound is heard. Range: 0--500(251 steps in
	increments of 2)
	* The ENTER key / foot switch can be used for tap input (refer to p.21).
4. FEEDBACK	Adjust the number of delay repeats. Range: 0--99(100 steps in increments of 1)

Mono pitch effect parameters (parameter type: MONO PITCH)

For effect type 37 of the preceding "Effect type" table, the following three parameters can be adjusted.

1. PITCH	Adjust the amount of pitch shift. Range: -24--0--+24(49 steps in semitone units)
	* +/-12is one octave. +/-24is two octaves.
2. ADJUST	Make fine adjustments to the amount of pitch shift. Range: -50--0--+50(101 steps in
	increments of 1)
	* +50 is a semitone sharp. -50is a semitone flat.
3. MODE	Select the processing method. Range: 1--3(3 steps)

23