22
Model VM08 Owner’s Manual
Effect parameter details

The parameters that can be adjusted will depend on the parameter type.

Reverb effect parameters (parameter type: REVERB)

For effect types 1--24 of the preceding "Effect type" table, the following four parameters can be ad-

justed.

1.REVERB TIME Adjust the length of reverberation. Range: 0.1--9.9 seconds (99 steps in 0.1 second units)
2.PRE DELAY Adjust the time from the original sound until reverberation begins. Range: 0--100 ms
(101 steps in 1 ms units)
3.HI RATIO Adjust the decay ratio of the high frequencies. Range: 0--10 (11 steps in increments of 1)
4.E/R BALANCE Adjust the volume of the early reflections. Range: 0--99 (100 steps in increments of 1)

Delay+reverb effect parameters (parameter type: DELAY+REVERB)

For effect types 25--28 of the preceding "Effect type" table, the following four parameters can be ad-

justed.

1.DELAY TIME Adjust the delay time: Range: 1--230 ms (230 steps in 1 ms units)
* The ENTER key / foot switch can be used for tap input (refer to p.21).
2.FEEDBACK Adjust the number of delay repeats. Range: 0--99 (100 steps in increments of 1)
3.DLY BAL Adjust the delay balance. Range: 0--99 (100 steps in increments of 1)
4.REVERB TIME Adjust the length of reverberation. Range: 0.1--9.9 seconds (99 steps in 0.1 second units)

Delay effect parameters (parameter type: DELAY)

For effect types 29 and 30 of the preceding "Effect type" table, the following four parameters can be

adjusted.

1.DELAY TIME Adjust the delay time. Range: 5--680 ms (136 steps in 5 ms units)
* The ENTER key / foot switch can be used for tap input (refer to p.21).
2.FEEDBACK Adjust the number of delay repeats. Range: 0--99 (100 steps in increments of 1)
3.HI RATIO Adjust the decay ratio of the high frequencies. Range: 0--10 (11 steps in increments of 1)
4.FILTER Adjust the tone of the delay sound. Range: L9~L1, -, H1~H9
*[-] is Filter Off
*L1~L9 = LPF (larger numbers will lower the cutoff frequency)
*H1~H9 = HPF (larger numbers will raise the cutoff frequency)

BPM delay effect parameters (parameter type: BPM DELAY)

For effect types 31 and 32 of the preceding "Effect type" table, the following four parameters can be

adjusted.

1.BPM Adjust the BPM. Range: 30--250 bpm (221 steps in units of 1)
* The ENTER key / foot switch can be used for tap input (refer to p.21).
2.NOTE Select the note value for the delay. Range: 24, 16, 8T, 16...8, 4T, 8., 4, 2T, 4., 2, 2., 1
*24 = 16th note sextuplets, 16 = 16th notes, 8T = 8th note triplets, 16. = dotted
sixteenth notes, 8 = 8th notes, 4T = quarter note triplets, 8. = dotted eighth notes,
4 = quarter notes, 2T = half-note triplets, 4. = dotted quarter notes, 2 = half notes,
2. = dotted half notes, 1 = whole notes
* The "." shown in the ninth character of the LCD indicates a dotted note.
* The "T" shown in the ninth character of the LCD indicates a triplet.
3.FEEDBACK Adjust the number of delay repeats. Range: 0--99 (100 steps in increments of 1)
4.FILTER Adjust the tone of the delay sound. Range: L9~L1, -, H1~H9
*[-] is Filter Off
*L1~L9 = LPF (larger numbers will lower the cutoff frequency)
*H1~H9 = HPF (larger numbers will raise the cutoff frequency)

Short delay effect parameters (parameter type: SHORT DELAY)

For effect type 33 of the preceding "Effect type" table, the following four parameters can be adjusted.

1.DELAY TIME Adjust the delay time. Range: 0.1--9.9 ms (99 steps in 0.1 ms units), 10--99 ms (90 steps
in 1 ms units), 100--200 ms (51 steps in 2 ms units)
* The ENTER key / foot switch cannot be used for tap input.
2.FEEDBACK Adjust the number of delay repeats. Range: 0--99 (100 steps in increments of 1)
3.HI RATIO Adjust the decay ratio of the high frequencies. Range: 0--10 (11 steps in increments of 1)
4.FILTER Adjust the tone of the delay sound. Range: L9~L1, -, H1~H9
*[-] is Filter Off
*L1~L9 = LPF (larger numbers will lower the cutoff frequency)
*H1~H9 = HPF (larger numbers will raise the cutoff frequency)