Fujitsu C120-E276-11ENZ0(A) Preface

Preface

Purpose

This manual describes how to install the Gigabit Ethernet card into your SPARC Enterprise system, and configure the environmental

settings for the interface.

Target Reader

This manual is intended for system administrators responsible for installing the Gigabit Ethernet card.

To understand the concepts and procedures presented in this manual, you need a few years of experience in Oracle Solaris (in this manual,

abbreviated to Solaris) system administration and have a basic knowledge of networked systems.

Organization

This section describes how this manual is organized.

Chapter 1 Product Outline

Chapter 1 describes the distinctive features of the Gigabit Ethernet Card.

Chapter 2 Gigabit Ethernet Card Installation

Chapter 2 describes how to install the Gigabit Ethernet card.

Chapter 3 Setting Instructions

Chapter 3 provides an overview of the environment definition.

Chapter 4 LinkAggregation Feature

Chapter 4 describes how to use the LinkAggregation function.

Chapter 5 Troubleshooting

Chapter 5 provides information about how to troubleshoot and resolve problems you might encounter during installation.

Appendix A Messages

Appendix A explains the messages output by the driver software.

Appendix B Gigabit Ethernet Card LED Diagnosis

Appendix B explains details of the Gigabit Ethernet card LED diagnostics.

Appendix C Using FUJITSU PCI GigabitEthernet in a Cluster Environment

Appendix C describes notes when using the card in a Cluster System.

Appendix D Using FUJITSU PCI GigabitEthernet in Solaris Containers

Appendix D describes notes when using the card in Solaris Containers.

Appendix E Using FUJITSU PCI GigabitEthernet in Oracle VM Server for SPARC

Appendix E describes notes when using the card in Oracle VM Server for SPARC.

Appendix F Using FUJITSU PCI GigabitEthernet in Solaris 11 Network Virtualization

Appendix F describes notes when using the card in Solaris 11 Network Virtualization.

Appendix G PCI Slot Number and Device Name

Appendix G shows the PCI slot number and device name list for each SPARC Enterprise model.

Symbol

The following symbols are used in this manual:

- i -

Contents

Main Preface Revision History Page Contents Page Chapter 1 Product Outline 1.1 Key Features 1.2 Gigabit Ethernet Card Specifications 1.2.1 Specifications 1.2.2 Part Names and Features of Hardware Page Page Chapter 2 Gigabit Ethernet Card Installation 2.1 Installation of the Gigabit Ethernet Card 2.2 Identifying the Gigabit Ethernet Card 2.3 Cable Connection Page Page Page Page Chapter 3 Setting Instructions - - - - - - - 3.1 Driver Software Installation 3.2 Identification of Interface Name 3.3 Environment Setting 3.3.1 Environment Setting of IPv4 Interfaces 3. 4. 1. - 3.3.2 Environment Setting of IPv6 Interfaces fjgi* 1. fjgi* 2. 3.4 Identification of the Gigabit Ethernet Card - Identification of the Gigabit Ethernet Card Types and Instance Number - Identification of Slots with Installed Gigabit Ethernet Cards 3.5 Operation Mode Setup 3.5.1 Setting the fjgi.conf File Page * [Parameter Setting] - 1. 2. Page - - Method 2: Setting method of old style [Parameter List] [Parameter Setting] - - - - 1. 2. - - 3.5.2 JumboFrame Setup Page 3.5.3 Using the ndd(1M) command - after - How to Use the ndd(1M) Command - - The ndd(1M) Command Parameters Page - - - - - - 3.5.4 Using the dladm(1M) command Page - - - - - - - - 3.5.5 FCode Settings - - FCode Settings (Auto-Negotiation Mode)"), or after power cycling the system. - 36 - 3.6 Network Installation 3.7 VLAN Interface Setup 3.7.1 IEEE 802.1Q TagVLAN 3.7.2 Setting Up the VLAN Interface - - - - - Chapter 4 LinkAggregation Feature 4.1 About LinkAggregation Feature - - Data Distribution Mode Table 4.2 Data Distribution Mode - LACP Mode Table 4.3 LACP Mode 4.2 Configuration of the LinkAggregation Feature 4.2.1 Setting and Displaying the Configuration with the dladm(1M) Command 4.2.1.1 Create a LinkAggregation (dladm create-aggr) Page Page Page 4.2.1.2 Delete a LinkAggregation (dladm delete-aggr) 4.2.1.3 Modify a LinkAggregation (dladm modify-aggr) Page 4.2.1.4 Add Interfaces to a LinkAggregation (dladm add-aggr) 4.2.1.5 Remove Interfaces from a LinkAggregation (dladm remove-aggr) Page 4.2.1.6 Display LinkAggregation Statistics and Information (dladm show-aggr) Page - - 4.3 Notes Chapter 5 Troubleshooting Appendix A Messages A.1 Console Messages from the Driver Table A.1 Console Messages(NOTICE) from the FUJITSU PCI GigabitEthernet Driver Table A.2 Console Messages(WARNING) from the FUJITSU PCI GigabitEthernet Driver Table A.3 Console Messages from the FUJITSU PCI GigabitEthernet Driver Page Table A.4 Messages Reported by Machine Administration Appendix B Gigabit Ethernet Card LED Diagnosis B.1 Location and Meaning of the LEDs Page Page Page Appendix C Using FUJITSU PCI GigabitEthernet in a Cluster Environment C.1 Cluster Environment Support C.2 Cluster Environment Setup Procedure C.3 Notes Appendix D Using FUJITSU PCI GigabitEthernet in Solaris Containers D.1 Solaris Containers Support - - D.2 Solaris Containers Setup Procedure - - - 68 - Example: Removing fjgi0 from a Shared-IP Non-Global Zone (zone1). - Example: Adding fjgi2 to an Exclusive-IP Non-Global Zone (zone2). D.3 Notes Page Page - Appendix E Using FUJITSU PCI GigabitEthernet in Oracle VM Server for SPARC E.1 Oracle VM Server for SPARC Support E.2 Oracle VM Server for SPARC Setup Procedure - E.3 Notes - - 75 - of Oracle Documentation. Appendix F Using FUJITSU PCI GigabitEthernet in Solaris 11 Network Virtualization F.1 Solaris 11 Network Virtualization Support - - F.2 Solaris 11 Network Virtualization Setup Procedure Page - F.3 Notes - Appendix G PCI Slot Number and Device Name Page Page - SPARC Enterprise M8000/M9000 Page Page - SPARC Enterprise T1000 - SPARC Enterprise T2000