Fujitsu C120-E276-11ENZ0(A) [Parameter Setting], -

Parameter Value Description

Rem

Only flow control from the remote device

is allowed. Flow control from the local

device is not allowed.

LocSend

Only flow control from the local device is

allowed. Flow control from the remote

device is not allowed.

None Flow control is disabled.

fjgi_mtu 1500 (default) to 9000 (*3) MTU (byte) is specified.

AutoNegotiation_A

On (default)

Auto-Negotiation is enabled. The

interface will not be able to communicate

with remote device operating in fixed

mode (Auto-Negotiation disabled).

When SE0X7GD1X, SE0X7GQ1X,

SE0X7GQ2X is used in 1000Mbps mode,

use this setting.

Off Auto-Negotiation is disabled. (Forced

mode)

Role_A (*4)

Auto (default)

Master or Slave is set based on

negotiation with the remote device. (This

is effective only when

AutoNegotiation_A= On.)

Master Communication by Master.

Slave Communication by Slave.

ReceiveTicks 0 to 1000 (*3)

(default: 77)

Time to wait for an interrupt for receiving

is specified (micro seconds). (*5)

TransmitTicks 0 to 1000 (*3)

(default: 500)

Time to wait for an interrupt for

transmitting is specified (micro seconds).

(*5)

ReceiveMaxBD 1 to 500 (*3)

(default: 10)

The number of buffer descriptor to wait

for an interrupt for receiving is specified.

(*5)

TransmitMaxBD 1 to 500 (*3)

(default: 128)

The number of buffer descriptor to wait

for an interrupt for transmitting is

specified. (*5)

*1: Parameter is supported on 10/100/1000Base-T (SE0X7GD1X, SE0X7GQ1X, SE0X7GQ2X) adapters only.

*2: Parameter is effective only when AutoNegotiation_A=On. When AutoNegotiation_A=Off, it becomes FlowControl_A=None.

*3: Specify the value as a decimal figure.

*4: Parameter is supported on 10/100/1000Base-T (SE0X7GD1X, SE0X7GQ1X, SE0X7GQ2X) adapters in 1000Mbps mode only.

*5: These ReceiveTicks, TransmitTicks, ReceiveMaxBD or TransmitMaxBD parameters are tuning parameters about the performance.

[Parameter Setting]

The following shows how to set the parent and unit-address parameters in the fjgi.conf file.

-Find the fjgi device tree, device node and instance number in the /etc/path_to_inst file.

Example:

- 22 -

Contents

Main Preface Revision History Page Contents Page Chapter 1 Product Outline 1.1 Key Features 1.2 Gigabit Ethernet Card Specifications 1.2.1 Specifications 1.2.2 Part Names and Features of Hardware Page Page Chapter 2 Gigabit Ethernet Card Installation 2.1 Installation of the Gigabit Ethernet Card 2.2 Identifying the Gigabit Ethernet Card 2.3 Cable Connection Page Page Page Page Chapter 3 Setting Instructions - - - - - - - 3.1 Driver Software Installation 3.2 Identification of Interface Name 3.3 Environment Setting 3.3.1 Environment Setting of IPv4 Interfaces 3. 4. 1. - 3.3.2 Environment Setting of IPv6 Interfaces fjgi* 1. fjgi* 2. 3.4 Identification of the Gigabit Ethernet Card - Identification of the Gigabit Ethernet Card Types and Instance Number - Identification of Slots with Installed Gigabit Ethernet Cards 3.5 Operation Mode Setup 3.5.1 Setting the fjgi.conf File Page * [Parameter Setting] - 1. 2. Page - - Method 2: Setting method of old style [Parameter List] [Parameter Setting] - - - - 1. 2. - - 3.5.2 JumboFrame Setup Page 3.5.3 Using the ndd(1M) command - after - How to Use the ndd(1M) Command - - The ndd(1M) Command Parameters Page - - - - - - 3.5.4 Using the dladm(1M) command Page - - - - - - - - 3.5.5 FCode Settings - - FCode Settings (Auto-Negotiation Mode)"), or after power cycling the system. - 36 - 3.6 Network Installation 3.7 VLAN Interface Setup 3.7.1 IEEE 802.1Q TagVLAN 3.7.2 Setting Up the VLAN Interface - - - - - Chapter 4 LinkAggregation Feature 4.1 About LinkAggregation Feature - - Data Distribution Mode Table 4.2 Data Distribution Mode - LACP Mode Table 4.3 LACP Mode 4.2 Configuration of the LinkAggregation Feature 4.2.1 Setting and Displaying the Configuration with the dladm(1M) Command 4.2.1.1 Create a LinkAggregation (dladm create-aggr) Page Page Page 4.2.1.2 Delete a LinkAggregation (dladm delete-aggr) 4.2.1.3 Modify a LinkAggregation (dladm modify-aggr) Page 4.2.1.4 Add Interfaces to a LinkAggregation (dladm add-aggr) 4.2.1.5 Remove Interfaces from a LinkAggregation (dladm remove-aggr) Page 4.2.1.6 Display LinkAggregation Statistics and Information (dladm show-aggr) Page - - 4.3 Notes Chapter 5 Troubleshooting Appendix A Messages A.1 Console Messages from the Driver Table A.1 Console Messages(NOTICE) from the FUJITSU PCI GigabitEthernet Driver Table A.2 Console Messages(WARNING) from the FUJITSU PCI GigabitEthernet Driver Table A.3 Console Messages from the FUJITSU PCI GigabitEthernet Driver Page Table A.4 Messages Reported by Machine Administration Appendix B Gigabit Ethernet Card LED Diagnosis B.1 Location and Meaning of the LEDs Page Page Page Appendix C Using FUJITSU PCI GigabitEthernet in a Cluster Environment C.1 Cluster Environment Support C.2 Cluster Environment Setup Procedure C.3 Notes Appendix D Using FUJITSU PCI GigabitEthernet in Solaris Containers D.1 Solaris Containers Support - - D.2 Solaris Containers Setup Procedure - - - 68 - Example: Removing fjgi0 from a Shared-IP Non-Global Zone (zone1). - Example: Adding fjgi2 to an Exclusive-IP Non-Global Zone (zone2). D.3 Notes Page Page - Appendix E Using FUJITSU PCI GigabitEthernet in Oracle VM Server for SPARC E.1 Oracle VM Server for SPARC Support E.2 Oracle VM Server for SPARC Setup Procedure - E.3 Notes - - 75 - of Oracle Documentation. Appendix F Using FUJITSU PCI GigabitEthernet in Solaris 11 Network Virtualization F.1 Solaris 11 Network Virtualization Support - - F.2 Solaris 11 Network Virtualization Setup Procedure Page - F.3 Notes - Appendix G PCI Slot Number and Device Name Page Page - SPARC Enterprise M8000/M9000 Page Page - SPARC Enterprise T1000 - SPARC Enterprise T2000