Fujitsu C120-E276-11ENZ0(A) -

-The following example shows how to add a virtual switch (vsw) device (ldm add-vsw)

/opt/SUNWldm/bin/ldm add-vsw net-dev=device vswitch_name ldom (device: network device

vswitch_name: virtual switch device

ldom: Logical Domain)

Example: Adding primary-vsw0 of fjgi2 to the Control Domain (primary).

# /opt/SUNWldm/bin/ldm add-vsw net-dev=fjgi2 primary-vsw0 primary

(Note 1) In Solaris 11, the vanity name (net4) is specified as fjgi2.

(Note 2) Reboot the Control Domain to make this setting effective.

Execute the following command from ok prompt.

ok boot -r

-The following example shows how to display a virtual switch (vsw) device (ldm list-services)

/opt/SUNWldm/bin/ldm list-services ldom (ldom: Logical Domain)

Example: Displaying services of the Control Domain (primary).

# /opt/SUNWldm/bin/ldm list-services primary

VDS

NAME VOLUME OPTIONS DEVICE

primary-vds0

VCC

NAME PORT-RANGE

primary-vcc0 5000-5100

VSW

NAME MAC NET-DEV DEVICE MODE

primary-vsw0 00:15:17:13:81:f8 fjgi2 switch@0 prog,promisc

(Note) In Solaris 11, the vanity name (net4) is specified as fjgi2.

-The following example shows how to add a virtual network (vnet) device (ldm add-vsw)

/opt/SUNWldm/bin/ldm add-vnet if_name vswitch_name ldom (if_name: virtual network device

vswitch_name: virtual switch device

ldom: Logical Domain)

Example: Adding a virtual switch (primary-vsw0) of fjgi2 to the Guest Domain (ldg1).

# /opt/SUNWldm/bin/ldm add-vnet vnet0 primary-vsw0 ldg1

(Note) Execute the following commands to make this setting effective.

If the Guest Domain has not started, execute the following commands.

# /opt/SUNWldm/bin/ldm bind-domain ldg1

# /opt/SUNWldm/bin/ldm start-domain ldg1

If the Guest Domain has already started, execute the following commands.

# /opt/SUNWldm/bin/ldm stop-domain ldg1

# /opt/SUNWldm/bin/ldm unbind-domain ldg1

# /opt/SUNWldm/bin/ldm bind-domain ldg1

# /opt/SUNWldm/bin/ldm start-domain ldg1

-The following example shows how to display a virtual network (vnet) device (ldm list-domain)

/opt/SUNWldm/bin/ldm list-domain -l ldom (ldom: Logical Domain)

Example: Displaying the status of the Guest Domain (ldg1).

- 74 -

Contents

Main Preface Revision History Page Contents Page Chapter 1 Product Outline 1.1 Key Features 1.2 Gigabit Ethernet Card Specifications 1.2.1 Specifications 1.2.2 Part Names and Features of Hardware Page Page Chapter 2 Gigabit Ethernet Card Installation 2.1 Installation of the Gigabit Ethernet Card 2.2 Identifying the Gigabit Ethernet Card 2.3 Cable Connection Page Page Page Page Chapter 3 Setting Instructions - - - - - - - 3.1 Driver Software Installation 3.2 Identification of Interface Name 3.3 Environment Setting 3.3.1 Environment Setting of IPv4 Interfaces 3. 4. 1. - 3.3.2 Environment Setting of IPv6 Interfaces fjgi* 1. fjgi* 2. 3.4 Identification of the Gigabit Ethernet Card - Identification of the Gigabit Ethernet Card Types and Instance Number - Identification of Slots with Installed Gigabit Ethernet Cards 3.5 Operation Mode Setup 3.5.1 Setting the fjgi.conf File Page * [Parameter Setting] - 1. 2. Page - - Method 2: Setting method of old style [Parameter List] [Parameter Setting] - - - - 1. 2. - - 3.5.2 JumboFrame Setup Page 3.5.3 Using the ndd(1M) command - after - How to Use the ndd(1M) Command - - The ndd(1M) Command Parameters Page - - - - - - 3.5.4 Using the dladm(1M) command Page - - - - - - - - 3.5.5 FCode Settings - - FCode Settings (Auto-Negotiation Mode)"), or after power cycling the system. - 36 - 3.6 Network Installation 3.7 VLAN Interface Setup 3.7.1 IEEE 802.1Q TagVLAN 3.7.2 Setting Up the VLAN Interface - - - - - Chapter 4 LinkAggregation Feature 4.1 About LinkAggregation Feature - - Data Distribution Mode Table 4.2 Data Distribution Mode - LACP Mode Table 4.3 LACP Mode 4.2 Configuration of the LinkAggregation Feature 4.2.1 Setting and Displaying the Configuration with the dladm(1M) Command 4.2.1.1 Create a LinkAggregation (dladm create-aggr) Page Page Page 4.2.1.2 Delete a LinkAggregation (dladm delete-aggr) 4.2.1.3 Modify a LinkAggregation (dladm modify-aggr) Page 4.2.1.4 Add Interfaces to a LinkAggregation (dladm add-aggr) 4.2.1.5 Remove Interfaces from a LinkAggregation (dladm remove-aggr) Page 4.2.1.6 Display LinkAggregation Statistics and Information (dladm show-aggr) Page - - 4.3 Notes Chapter 5 Troubleshooting Appendix A Messages A.1 Console Messages from the Driver Table A.1 Console Messages(NOTICE) from the FUJITSU PCI GigabitEthernet Driver Table A.2 Console Messages(WARNING) from the FUJITSU PCI GigabitEthernet Driver Table A.3 Console Messages from the FUJITSU PCI GigabitEthernet Driver Page Table A.4 Messages Reported by Machine Administration Appendix B Gigabit Ethernet Card LED Diagnosis B.1 Location and Meaning of the LEDs Page Page Page Appendix C Using FUJITSU PCI GigabitEthernet in a Cluster Environment C.1 Cluster Environment Support C.2 Cluster Environment Setup Procedure C.3 Notes Appendix D Using FUJITSU PCI GigabitEthernet in Solaris Containers D.1 Solaris Containers Support - - D.2 Solaris Containers Setup Procedure - - - 68 - Example: Removing fjgi0 from a Shared-IP Non-Global Zone (zone1). - Example: Adding fjgi2 to an Exclusive-IP Non-Global Zone (zone2). D.3 Notes Page Page - Appendix E Using FUJITSU PCI GigabitEthernet in Oracle VM Server for SPARC E.1 Oracle VM Server for SPARC Support E.2 Oracle VM Server for SPARC Setup Procedure - E.3 Notes - - 75 - of Oracle Documentation. Appendix F Using FUJITSU PCI GigabitEthernet in Solaris 11 Network Virtualization F.1 Solaris 11 Network Virtualization Support - - F.2 Solaris 11 Network Virtualization Setup Procedure Page - F.3 Notes - Appendix G PCI Slot Number and Device Name Page Page - SPARC Enterprise M8000/M9000 Page Page - SPARC Enterprise T1000 - SPARC Enterprise T2000