Fujitsu C120-E276-11ENZ0(A) - page 52

1. Define the relation between the IP address and the hostname in the /etc/inet/hosts file.

Example (Hostname is giga-lacp and its IP address is 192.168.150.1):

# cat /etc/hosts

192.168.150.1 giga-lacp

2. Setup the hostname and prefix length to aggr1 by ipadm(1M) command.

Example (Hostname is giga-lacp and prefix length is 24):

# ipadm create-ip aggr1

# ipadm create-addr -T static -a giga-lacp/24 aggr1/v4static

-The following example shows how to create a VLAN interface with the "aggr-link=aggr1" LinkAggregation Group(*4).

("IP address=192.168.151.1" is assigned to the VLAN interface "aggr2001" of "VID=2".):

# dladm create-vlan -l aggr1 -v 2

# ifconfig aggr2001 plumb 192.168.151.1 up

*4: After rebooting the system, the VLAN interface aggr2001 is not activated.

-The following example shows how to setup the VLAN interface with the "aggr-link=aggr1" LinkAggregation Group for

activation after rebooting the system.

("IP address=192.168.151.1" is assigned to the VLAN interface "aggr2001" of "VID=2".):

1. Create the VLAN interface by dladm(1M) command.

2. Example (the VLAN interface "aggr2001" of "VID=2"):

# dladm create-vlan -l aggr1 -v 2

3. Define the relation between the IP address and the hostname in the /etc/inet/hosts file.

Example (Hostname is giga-lacp and its IP address is 192.168.150.1):

# cat /etc/hosts

192.168.151.1 giga-vlan

4. Setup the hostname and prefix length to aggr2001 by ipadm(1M) command.

Example (Hostname is giga-lacp and prefix length is 24):

# ipadm create-ip aggr2001

# ipadm create-addr -T static -a giga-vlan/24 aggr2001/v4static

Note

-Before creating a LinkAggregation Group, all interfaces to be assigned to the group must be in an inactive state.

-By using the dladm create-aggr command, the policy, the LACP mode and the LACP timer are set to default values ("L4 distribution",

"off mode" and "short"). To set parameters to non-default values, it is necessary to change the LinkAggregation settings by using the

dladm modify-aggr command. For more information about this command, please refer to "4.2.1.3 Modify a LinkAggregation (dladm

modify-aggr)".

-After rebooting the system, the LinkAggregation settings remain effective.

-For more information about this command, please refer to the "man pages section 1M: System Administration Commands" of Oracle

Documentation.

- 46 -

Contents

Main Preface Revision History Page Contents Page Chapter 1 Product Outline 1.1 Key Features 1.2 Gigabit Ethernet Card Specifications 1.2.1 Specifications 1.2.2 Part Names and Features of Hardware Page Page Chapter 2 Gigabit Ethernet Card Installation 2.1 Installation of the Gigabit Ethernet Card 2.2 Identifying the Gigabit Ethernet Card 2.3 Cable Connection Page Page Page Page Chapter 3 Setting Instructions - - - - - - - 3.1 Driver Software Installation 3.2 Identification of Interface Name 3.3 Environment Setting 3.3.1 Environment Setting of IPv4 Interfaces 3. 4. 1. - 3.3.2 Environment Setting of IPv6 Interfaces fjgi* 1. fjgi* 2. 3.4 Identification of the Gigabit Ethernet Card - Identification of the Gigabit Ethernet Card Types and Instance Number - Identification of Slots with Installed Gigabit Ethernet Cards 3.5 Operation Mode Setup 3.5.1 Setting the fjgi.conf File Page * [Parameter Setting] - 1. 2. Page - - Method 2: Setting method of old style [Parameter List] [Parameter Setting] - - - - 1. 2. - - 3.5.2 JumboFrame Setup Page 3.5.3 Using the ndd(1M) command - after - How to Use the ndd(1M) Command - - The ndd(1M) Command Parameters Page - - - - - - 3.5.4 Using the dladm(1M) command Page - - - - - - - - 3.5.5 FCode Settings - - FCode Settings (Auto-Negotiation Mode)"), or after power cycling the system. - 36 - 3.6 Network Installation 3.7 VLAN Interface Setup 3.7.1 IEEE 802.1Q TagVLAN 3.7.2 Setting Up the VLAN Interface - - - - - Chapter 4 LinkAggregation Feature 4.1 About LinkAggregation Feature - - Data Distribution Mode Table 4.2 Data Distribution Mode - LACP Mode Table 4.3 LACP Mode 4.2 Configuration of the LinkAggregation Feature 4.2.1 Setting and Displaying the Configuration with the dladm(1M) Command 4.2.1.1 Create a LinkAggregation (dladm create-aggr) Page Page Page 4.2.1.2 Delete a LinkAggregation (dladm delete-aggr) 4.2.1.3 Modify a LinkAggregation (dladm modify-aggr) Page 4.2.1.4 Add Interfaces to a LinkAggregation (dladm add-aggr) 4.2.1.5 Remove Interfaces from a LinkAggregation (dladm remove-aggr) Page 4.2.1.6 Display LinkAggregation Statistics and Information (dladm show-aggr) Page - - 4.3 Notes Chapter 5 Troubleshooting Appendix A Messages A.1 Console Messages from the Driver Table A.1 Console Messages(NOTICE) from the FUJITSU PCI GigabitEthernet Driver Table A.2 Console Messages(WARNING) from the FUJITSU PCI GigabitEthernet Driver Table A.3 Console Messages from the FUJITSU PCI GigabitEthernet Driver Page Table A.4 Messages Reported by Machine Administration Appendix B Gigabit Ethernet Card LED Diagnosis B.1 Location and Meaning of the LEDs Page Page Page Appendix C Using FUJITSU PCI GigabitEthernet in a Cluster Environment C.1 Cluster Environment Support C.2 Cluster Environment Setup Procedure C.3 Notes Appendix D Using FUJITSU PCI GigabitEthernet in Solaris Containers D.1 Solaris Containers Support - - D.2 Solaris Containers Setup Procedure - - - 68 - Example: Removing fjgi0 from a Shared-IP Non-Global Zone (zone1). - Example: Adding fjgi2 to an Exclusive-IP Non-Global Zone (zone2). D.3 Notes Page Page - Appendix E Using FUJITSU PCI GigabitEthernet in Oracle VM Server for SPARC E.1 Oracle VM Server for SPARC Support E.2 Oracle VM Server for SPARC Setup Procedure - E.3 Notes - - 75 - of Oracle Documentation. Appendix F Using FUJITSU PCI GigabitEthernet in Solaris 11 Network Virtualization F.1 Solaris 11 Network Virtualization Support - - F.2 Solaris 11 Network Virtualization Setup Procedure Page - F.3 Notes - Appendix G PCI Slot Number and Device Name Page Page - SPARC Enterprise M8000/M9000 Page Page - SPARC Enterprise T1000 - SPARC Enterprise T2000