Fujitsu C120-E276-11ENZ0(A) -

1. Execute the following commands in the Global Zone.

# /usr/sbin/dladm create-aggr -d fjgi0 -d fjgi1 -d fjgi2 2

# zonecfg -z zone2

zonecfg:zone2> set ip-type=exclusive

zonecfg:zone2> add net

zonecfg:zone2:net> set physical=aggr2

zonecfg:zone2:net> end

zonecfg:zone2> exit

(Note) Reboot the Exclusive-IP Non-Global Zone to make this setting effective.

If the Exclusive-IP Non-Global Zone has not booted, execute the following command.

# zoneadm -z zonename boot

If the Exclusive-IP Non-Global Zone has booted, execute the following command.

# zoneadm -z zonename reboot

2. Execute the following command in the Exclusive-IP Non-Global Zone.

# ifconfig aggr2 plumb 192.168.170.1 up

-Solaris 11

Example: Adding aggr2 which is a LinkAggregation Group with fjgi0 (this vanity name is net2), fjgi1 (this vanity name is net3),

fjgi2 (this vanity name is net4) to an Exclusive-IP Non-Global Zone (zone1).

1. Execute the following commands in the Global Zone.

# /usr/sbin/dladm create-aggr -l net2 -l net3 -l net4 aggr2

# zonecfg -z zone2

zonecfg:zone2> set ip-type=exclusive

zonecfg:zone2> add net

zonecfg:zone2:net> set physical=aggr2

zonecfg:zone2:net> end

zonecfg:zone2> exit

(Note) Reboot the Exclusive-IP Non-Global Zone to make this setting effective.

If the Exclusive-IP Non-Global Zone has not booted, execute the following command.

# zoneadm -z zonename boot

If the Exclusive-IP Non-Global Zone has booted, execute the following command.

# zoneadm -z zonename reboot

2. Execute the following command in the Exclusive-IP Non-Global Zone.

# ifconfig aggr2 plumb 192.168.170.1 up

-For more information about Solaris Containers, please refer to "System Administration Guide: Solaris Containers-Resource

Management and Solaris Zones" of Oracle Documentation.

- 72 -

Contents

Main Preface Revision History Page Contents Page Chapter 1 Product Outline 1.1 Key Features 1.2 Gigabit Ethernet Card Specifications 1.2.1 Specifications 1.2.2 Part Names and Features of Hardware Page Page Chapter 2 Gigabit Ethernet Card Installation 2.1 Installation of the Gigabit Ethernet Card 2.2 Identifying the Gigabit Ethernet Card 2.3 Cable Connection Page Page Page Page Chapter 3 Setting Instructions - - - - - - - 3.1 Driver Software Installation 3.2 Identification of Interface Name 3.3 Environment Setting 3.3.1 Environment Setting of IPv4 Interfaces 3. 4. 1. - 3.3.2 Environment Setting of IPv6 Interfaces fjgi* 1. fjgi* 2. 3.4 Identification of the Gigabit Ethernet Card - Identification of the Gigabit Ethernet Card Types and Instance Number - Identification of Slots with Installed Gigabit Ethernet Cards 3.5 Operation Mode Setup 3.5.1 Setting the fjgi.conf File Page * [Parameter Setting] - 1. 2. Page - - Method 2: Setting method of old style [Parameter List] [Parameter Setting] - - - - 1. 2. - - 3.5.2 JumboFrame Setup Page 3.5.3 Using the ndd(1M) command - after - How to Use the ndd(1M) Command - - The ndd(1M) Command Parameters Page - - - - - - 3.5.4 Using the dladm(1M) command Page - - - - - - - - 3.5.5 FCode Settings - - FCode Settings (Auto-Negotiation Mode)"), or after power cycling the system. - 36 - 3.6 Network Installation 3.7 VLAN Interface Setup 3.7.1 IEEE 802.1Q TagVLAN 3.7.2 Setting Up the VLAN Interface - - - - - Chapter 4 LinkAggregation Feature 4.1 About LinkAggregation Feature - - Data Distribution Mode Table 4.2 Data Distribution Mode - LACP Mode Table 4.3 LACP Mode 4.2 Configuration of the LinkAggregation Feature 4.2.1 Setting and Displaying the Configuration with the dladm(1M) Command 4.2.1.1 Create a LinkAggregation (dladm create-aggr) Page Page Page 4.2.1.2 Delete a LinkAggregation (dladm delete-aggr) 4.2.1.3 Modify a LinkAggregation (dladm modify-aggr) Page 4.2.1.4 Add Interfaces to a LinkAggregation (dladm add-aggr) 4.2.1.5 Remove Interfaces from a LinkAggregation (dladm remove-aggr) Page 4.2.1.6 Display LinkAggregation Statistics and Information (dladm show-aggr) Page - - 4.3 Notes Chapter 5 Troubleshooting Appendix A Messages A.1 Console Messages from the Driver Table A.1 Console Messages(NOTICE) from the FUJITSU PCI GigabitEthernet Driver Table A.2 Console Messages(WARNING) from the FUJITSU PCI GigabitEthernet Driver Table A.3 Console Messages from the FUJITSU PCI GigabitEthernet Driver Page Table A.4 Messages Reported by Machine Administration Appendix B Gigabit Ethernet Card LED Diagnosis B.1 Location and Meaning of the LEDs Page Page Page Appendix C Using FUJITSU PCI GigabitEthernet in a Cluster Environment C.1 Cluster Environment Support C.2 Cluster Environment Setup Procedure C.3 Notes Appendix D Using FUJITSU PCI GigabitEthernet in Solaris Containers D.1 Solaris Containers Support - - D.2 Solaris Containers Setup Procedure - - - 68 - Example: Removing fjgi0 from a Shared-IP Non-Global Zone (zone1). - Example: Adding fjgi2 to an Exclusive-IP Non-Global Zone (zone2). D.3 Notes Page Page - Appendix E Using FUJITSU PCI GigabitEthernet in Oracle VM Server for SPARC E.1 Oracle VM Server for SPARC Support E.2 Oracle VM Server for SPARC Setup Procedure - E.3 Notes - - 75 - of Oracle Documentation. Appendix F Using FUJITSU PCI GigabitEthernet in Solaris 11 Network Virtualization F.1 Solaris 11 Network Virtualization Support - - F.2 Solaris 11 Network Virtualization Setup Procedure Page - F.3 Notes - Appendix G PCI Slot Number and Device Name Page Page - SPARC Enterprise M8000/M9000 Page Page - SPARC Enterprise T1000 - SPARC Enterprise T2000