Fujitsu C122-E177-01EN TABLE 1.54 [MMB#x] Window button

MMB Web-UI (Web User Interface) Operations

Items

Description

On/ Off of the Location LED can be controlled by clicking [On], [Off] buttons.

Reset MMB Resets the MMB if this check box is checked.

When this check box is checked, [Switch Over to MMB] mentioned below cannot

be set.

Switch Over to MMB Switches the Active/Standby of the MMB if this check box is checked.

When this check box is checked, [Reset MMB] mentioned above cannot be set.

Remarks

This check box is displayed only, when two MMBs are mounted.

Enable/Disable MMB Controls Enable/ Disable of the MMB.

Because this item is a facility used fo r testing, it is not possible to usually set it.

Voltage

Sensor

Displays the Voltage sensor type.

P3.3VL

P1.5VL

P1.5VL_CPLD

P1.2VL

P1.0VL

P0.75VL

Voltage

Displays the current power voltage.

Threshold

Warning

(Low/High) Lower and upper limits of the warning-level voltage.

Displays “ – ”, when the threshold is not set.

Displays the power voltage in the last two decimal places.

Critical

(Low/High) Lower and upper limits of the critical-level voltage.

Displays “ – ”, when the threshold is not set.

Displays the power voltage in the last two decimal places.

TABLE 1.54 [MMB#x] Window button

Buttons

Description

On

Turns on the Location LED when the [On] button is clicked.

Off

Turns off the Location LED when the [Off] button is clicked

Apply

Click the [Apply] button to set the specified control information.

Cancel

Click the [Cancel] button to restore the original information and not set the spe cif ied inf orma t ion.

(1) Menu Operation

[System] – [MMB] – [MMB#x]

(2) Window Operations

Confirmation dialogue box is displayed. Specify the information which shows the change in MMB

status, click the [Apply] button. Sets the information which shows the change in MMB status.

[Message]

This section describes the messages to be displayed on this window.

Message Number

Message

I_00013

Setting completed.

I_00052

MMB switch processing has started.

I_00095

The standby MMB is rebooting now. Please wait several minutes.

E_00100

Failed to set the LED

E_00125

Failed to switch over to another MMB.

E_00125

Failed to change Enable/Disable status of the MMB.

E_00125

Failed to reset the MMB.

I_00213

%aa cannot be executed because the system is under maintenance.

I_00467

The reboot is done. Login after a while.

W_00413

Nothing is selected.

Contents

Main Preface For Safe Operation How to use this manual About this product Storage of accessories Organization of this manual Manuals for the PRIMEQUEST 2000 series Title Related manuals Title Abbreviations Formal product name Trademarks Notation Font or symbol Command syntax Notes on notations Alert messages Alert messages in the text Product operating environment Note Safety Precautions List of important alert ite ms The important warning matter that has been described in this manual is as follows. Warning labels Revision History Contents Page Page Page Page Page Page Figures Page Page Page Page Tables Page Page Page Page Page Page Page CHAPTER 1 MMB Web-UI (Web User Interface) Operations 1.1 Web-UI Menus TABLE 1.1 User privileges 1.1.1 Web-UI menus (Administrator) TABLE 1.2 Web-UI menus (Administrator) Page Page 1.1.2 Web-UI menus (Operator) TABLE 1.3 Web-UI menus (Operator) Page Page 1.1.3 Web-UI menus (Partition Operator) TABLE 1.4 Web-UI menus (Partition Operator) Page Page Page 1.1.4 Web-UI menus (User) TABLE 1.5 Web-UI menus (User) Page Page 1.1.5 Web-UI menus (CE) TABLE 1.6 Web-UI menus (CE) Page Page Page 1.1.6 Web-UI menus in maintenance mode TABLE 1.7 Types of maintenance mode 1.1.7 Web-UI menus in maintenance mode (Administrator) TABLE 1.8 Web-UI menus in maintenance mode (Administrator) 1.1.8 Web-UI menus in maintenance mode (Operator) TABLE 1.9 Web-UI menus in maintenance mode (Operator) 1.1.9 Web-UI menus in maintenance mode (Partition Operator) TABLE 1.10 Web-UI menus in maintenance mode (Partition Oper ator) 1.1.10 Web-UI menus in maintenance mode (User) TABLE 1.11 Web-UI menus in maintenance mode (User) Page 1.1.11 Web-UI menus in maintenance mode (CE) TABLE 1.12 Web-UI menus in maintenance mode (CE) 1.1.12 Web-UI menus in maintenance mode (maintenance personnel) TABLE 1.13 Web-UI menus in maintenance mode (maintenance personne l) Page 1.1.13 Web-UI menus (PRIMEQUEST 2800B model) TABLE 1.14 Web-UI menus (PRIMEQUEST 2800B model) Page Page 1.2 [System] Menu for PRIMEQUEST 2400E/2800E 1.2.1 [System Status] window FIGURE 1.1 [System Status] window TABLE 1.15 Status of Unit and its Icons 1.2.2 [System Event Log] Window FIGURE 1.2 [System Event Log] window TABLE 1.17 Items displayed in [System Event Log] Window Warning : Not a severe error, but an error is likely in future Info : Shows the information like Partition power ON TABLE 1.18 Buttons on [System Event Log] Window FIGURE 1.3 [System Event Log (Collect)] Window [System Event Log Filtering Condition] Window Page All: Filtering is not done by Unit. New event first Old event first TABLE 1.20 [System Events Log Filtering Condition] Window Buttons 1.2.3 [Operation Log] Window FIGURE 1.5 [Operation Log] Window TABLE 1.21 Display items of [Operation Log] window TABLE 1.22 [Operation Log] Window Buttons [Operation Log Filtering Condition] Window FIGURE 1.6 [Operating Log Filtering Condition] Window TABLE 1.23 Display and Set Items of [Operating Log Filtering Conditio n] Window New event first Old event first First event: Set to first event Specified Time: Set to specified time Last event : Set to last event Specified Time : Set to specified time TABLE 1.24 Buttons on [Operation Log Filtering Condition] window 1.2.4 [Partition Event Log] Window FIGURE 1.7 [Partition Event Log] window TABLE 1.25 Display items of [Partition Event Log] window Information: Event assumed as information when partition power is on. TABLE 1.26 [Partition Event Log] Window Buttons [Partition Event Log Filtering Condition] Window FIGURE 1.8 [Partition Event Log Filtering Condition] Window TABLE 1.27 Display and Set Items of [Partition Event Log Filtering Co ndition] Window Partition Operator privilege. : [Specified] and Partition to be managed is turned on. TABLE 1.28 Buttons on the [Partition Event Log Filtering Condition] W indow 1.2.5 [System Information] Window FIGURE 1.9 [System Information] Window Characters which can be entered: Alphanumeric characters, half-width space. The Half-width space cannot be used as last character. TABLE 1.30 Buttons on the [System Information] Window 1.2.6 [Firmware Information] Window Page 1.2.7 [System Setup] Window FIGURE 1.11 [System Setup] Window TABLE 1.32 Display Items and Setting Items in [System Setup] Window 100V 200V Single: primary power feed mode Dual: dual power feed mode Restore: Restores the status immediately before the power failure. If the Schedule Sync: If the partition is in the operating time zone, power of partition Redundant Non-redundant Enable Disable TABLE 1.33 [System Setup] window button 1.2.8 [System Power Control] window In case of following condition, confirm the contents by referring to "11.2 Troubleshooting" of FIGURE 1.12 [System Power Control] Window TABLE 1.34 Display Items and Setting Items in [System Power Control] W indow TABLE 1.35 [System Power Control] Window Button 1.2.9 [LEDs] window FIGURE 1.13 [LEDs] Window TABLE 1.36 Display Items and Setting Items in [LEDs] Window TABLE 1.37 [LEDs] Window Button Page Off PSU_P : PSU supporting 80PLUS PLATINUM FANU : Module of FAN only TABLE 1.39 Button of [Power Supply] Window Page TABLE 1.40 Display items of [Fans] window Non-Redundant: Insufficient Resource: The number of fans is less due to OK Not-present Failed TABLE 1.41 [Fans] Window Button 1.2.12 [Temperature] window OK Not-present Warning Critical Warning: Low/High Critical :Low/High 1.2.13 [SB] Menu Page Page Page Page Page Operational Available Failed Hot Spare Rebuilding Not-present Physical : Hardware RAID Failed Page TABLE 1.44 [SB#x] Window Button [SB#x Status Clear] Window FIGURE 1.24 [SB#x Status Clear] Window (Message Display) Check the [Clear Status of common parts] check box to clear the common parts. Display when there is no CPU/DIMM installed FIGURE 1.25 [SB#x] Window (When there is no CPU/DIMM) 1.2.14 [IOU] Menu [IOU#0] ~ [IOU#3] [IOU#x] Window Page Page FIGURE 1.28 [IOU#x] Window (3) TABLE 1.45 Display Items and Setting Items in [IOU#x] Window IOU_10GbE IOU_1GbE Page TABLE 1.46 Button of [IOB#x] Screen 1.2.15 [DU] Menu FIGURE 1.29 [DU#x] Window TABLE 1.47 Display and Setting items of [DU#x] Window Online On Battery Charging Discharging Battery Low Relearn Required Failed Not-present Operational Available Failed Hot Spare Rebuilding Not-present Physical : Hardware RAID Logical : Software RAID Rebuilding : It is shown for a physical drive to execute the rebuild of the RAID MDC Running : It is shown for a logical drive to execute MDC(Make Data 1.2.16 [PCI_Box] Menu FIGURE 1.30 [PCI_Box] Window (1) Page FIGURE 1.33 [PCI_Box] Window (4) TABLE 1.49 Display Items of [PCI_Box#x] Window Page Page TABLE 1.50 [MMB#x] Window button 1.2.17 [OPL] Window [OPL] Window FIGURE 1.34 [OPL] window TABLE 1.51 Display items of [OPL] Window TABLE 1.52 Button on [OPL] window [MMB#0] ~ [MMB#1] [MMB#x] Window FIGURE 1.35 [MMB#x] Window TABLE 1.53 Display of [MMB#x] Window / setting items TABLE 1.54 [MMB#x] Window button 1.2.19 [Disk Enclosure] Menu FIGURE 1.36 [Disk Enclosure#x] Window (1) FIGURE 1.37 [Disk Enclosure#x] Window (2) TABLE 1.55 Display and Setting items of [Disk Enclosure#x] W indow OK Not-present Warning Critical Warning: Low/High Online Critical :Low/High Page Expander# FAN# 1.3 [Partition] Menu for PRIMEQUEST 2400E/2800E 1.3.1 [Power Control] Window FIGURE 1.38 [Power Control] Window FIGURE 1.39 [Power Control] Window (Grayout Display) TABLE 1.56 Display Items and Set Items of [Power Control] Window Page TABLE 1.57 [Power Control] Window Buttons Error Display FIGURE 1.40 Display of Errors of [Power Control] Window 1.3.2 [Schedule] Menu [Schedule Control] window FIGURE 1.41 [Schedule Control] Window TABLE 1.58 Display Items and Setting Items of [Schedule Control] W indow Page TABLE 1.59 [Schedule Control] Window Buttons [Schedule list] Window FIGURE 1.42 [Schedule List] Window TABLE 1.60 Display Items and Set Items of [Schedule List] Windo w TABLE 1.61 [Schedule List] Window Buttons [Add Schedule] window/ [Edit Schedule] window FIGURE 1.43 [Schedule List] Window TABLE 1.62 Display Items and Set Items of [Add Schedule] Window TABLE 1.63 [Add Schedule] Window Buttons 1.3.3 [Console Redirection Setup] window [IPv4 Console Redirection Setup] window FIGURE 1.44 [IPv4 Console Redirection Setup] TABLE 1.64 Display Items and Set Items of [IPv4 Console redirection Set up] Window TABLE 1.65 [IPv4 Console redirection Setup] Window Buttons [IPv6 Console Redirection Setup] window FIGURE 1.45 [IPv6 Console Redirection Setup] Window TABLE 1.66 Display Items and Set Items of [IPv6 Console redirecti on Setup] Window TABLE 1.67 [IPv6 Console redirection Setup] Window Buttons 1.3.4 [Partition Configuration] Men u FIGURE 1.46 [Partition Configuration] Window TABLE 1.68 Display Items and Set Items of [Add Schedule] Window TABLE 1.69 [Partition Configuration] Window Buttons [Set Partition Name] Button [Add SB/IOU to Partition] Window FIGURE 1.47 [Add SB/IOU to Partition] Window TABLE 1.70 Display Items and Set Items of [Add SB/IOU to Partition] W indow [Remove SB/IOU from Partition] Window FIGURE 1.48 [Remove SB/IOU from Partition] Window TABLE 1.71 Display Items and Set Items of [Remove SB/IOU to partitio n] Window [Partition Home] window FIGURE 1.49 [Partition Home] window 1.3.5 [Reserved SB Configuration] window FIGURE 1.50 [Reserved SB Configuration] Window TABLE 1.72 Display Items and Set Items of [Reserved SB Configuration] Window TABLE 1.73 [Reserved SB Configuration] Window Buttons 1.3.6 [Power Management Setup] Window FIGURE 1.51 [Power Management Setup] window TABLE 1.74 Display Items and Set Items of [Power Management Set up] Window TABLE 1.75 [Power Management Setup] Window Buttons 1.3.7 [Partition#x] Menu [Information] Window FIGURE 1.52 [Information] Window TABLE 1.76 Display Items of [Information] Window [ASR Control] Window FIGURE 1.53 [ASR (Automatic Server Restart) Control] Window TABLE 1.77 Display Items and Set Items of [ASR (Automatic Server Res tart) Control] Window NMI Power Cycle TABLE 1.78 [ASR (Automatic Server Restart) Control] Window Buttons [Console Redirection] Window FIGURE 1.54 [Console Redirection] Window TABLE 1.79 Display Items of [Console Redirection] Window [Mode] Window FIGURE 1.55 [Mode] Window TABLE 1.80 Display Items and Setting Items in [Mode] Window Page Page Page 1.4 [User Administration] Menu 1.4.1 [User List] window FIGURE 1.56 [User List] Window TABLE 1.81 Display items in the [User List] window TABLE 1.82 Buttons in the [User List] window [Add User] window FIGURE 1.57 [Add List] Window [Edit User] window FIGURE 1.58 [Edit List] Window TABLE 1.83 Setting and display items in the [Add User] and [Edit User] w indows TABLE 1.84 Buttons in the [Add User] and [Edit User] windows [Remove User] button 1.4.2 [Change Password] window FIGURE 1.59 [Change Password] window TABLE 1.85 Buttons in the [Change Password] window 1.4.3 [Who] window FIGURE 1.60 [Change Password] window TABLE 1.86 Display items in the [Who] window Page 1.5 [Network Configuration] Menu 1.5.1 [Date/Time] window FIGURE 1.61[Date/Time] window TABLE 1.87 Setting and display items in the [Date/Time] window TABLE 1.88 Buttons in the [Date/Time] window Page 1.5.2 [Network Interface] window [IPv4 Interface] window FIGURE 1.62 [IPv4 Interface] window (PRIMEQUEST 2400E/2800E) (1) FIGURE 1.63 [IPv4 Interface] window (PRIMEQUEST 2400E/2800E) (2) TABLE 1.89 Setting and display items in the [IPv4 Interface] window (PRI MEQUEST 2400E/2800E) Page Page TABLE 1.90 Setting and display items in the [IPv4 Interface] window (PRI MEQUEST 2800B) TABLE 1.91 Buttons in the [IPv4 Interface] window [IPv6 Interface] window FIGURE 1.66 [IPv6 Interface] window (PRIMEQUEST 2400E/2800E) (1) Page TABLE 1.92 Setting and display items in the [IPv6 Interface] window (PRI MEQUEST 2400E/2800E) FIGURE 1.68 [IPv6 Interface] window (PRIMEQUEST 2800B) (1) FIGURE 1.69 [IPv6 Interface] window (PRIMEQUEST 2800B) (2) TABLE 1.93 Setting and display items in the [IPv6 Interface] window (PRI MEQUEST 2800B) TABLE 1.94 Buttons in the [IPv6 Interface] window 1.5.3 [Management LAN Port Configuration] window Page Page TABLE 1.97 Buttons in the [Management LAN Port Configuration] window 1.5.4 [Network Protocols] window FIGURE 1.72 [Network Protocols] window TABLE 1.98 Setting and display items in the [Network Protocols] window TABLE 1.99 Buttons in the [Network Protocols] window 1.5.5 [Refresh Rate] window FIGURE 1.73 [Refresh Rate] window TABLE 1.100 Setting and display items in the [Refresh Rate] window TABLE 1.101 Buttons in the [Refresh Rate] window 1.5.6 [SNMP Configuration] window [SNMP Community] window FIGURE 1.74 [SNMP Community] window TABLE 1.102 Setting and display items in the [SNMP Community] windo w TABLE 1.103 Buttons in the [SNMP Community] window [SNMP Trap] window FIGURE 1.75 [SNMP Trap] window TABLE 1.104 Setting and display items in the [SNMP Trap] window TABLE 1.105 Buttons in the [SNMP Trap] window [SNMP v3 Configuration] window FIGURE 1.76 [SNMP v3 Configuration] window TABLE 1.106 Setting and display items in the [SNMP v3 Configuration] window TABLE 1.107 Buttons in the [SNMP v3 Configuration] window 1.5.7 [SSL] menu [Create CSR] window FIGURE 1.77 [Create CSR] window TABLE 1.108 Setting and display items in the [Create CSR] window TABLE 1.109 Buttons in the [Create CSR] window Microsoft Internet Explorar FIGURE 1.78 Confirmation dialog box [Export Key/CSR] window Cancel FIGURE 1.79 [Export Key/CSR] window TABLE 1.110 Buttons in the [Export Key/CSR] window [Import Certificate] window FIGURE 1.80 [Import Certificate] window TABLE 1.111 Buttons in the [Import Certificate] window [Create Selfsigned Certificate] window FIGURE 1.81 [Create Selfsigned Certificate] window TABLE 1.112 Display items in the [Create Selfsigned Certificate] windo w TABLE 1.113 Buttons in the [Create Selfsigned Certificate] window 1.5.8 [SSH] menu [Create SSH Server Key] window FIGURE 1.82 [Create SSH Server Key] window TABLE 1.114 Buttons in the [Create SSH Server Key] window 1.5.9 [Remote Server Management] window FIGURE 1.83 [Remote Server Management] window TABLE 1.115 Display and setting items in the [Remote Server Managem ent] window TABLE 1.116 Buttons in the [Remote Server Management] window [Edit User] window FIGURE 1.84 [Edit User] window TABLE 1.117 Display and setting items in the [Edit User] window TABLE 1.118 Buttons in the [Edit User] 1.5.10 [Access Control] window FIGURE 1.85 [Access Control] window TABLE 1.119 Setting and display items in the [Access Control] window TABLE 1.120 Buttons in the [Access Control] window [Add Filter]/[Edit Filter] window FIGURE 1.86 [Add Filter] window TABLE 1.121 Setting and display items in the [Add Filter] window TABLE 1.122 Buttons in the [Add Filter] window 1.5.11 [Alarm E-Mail] window FIGURE 1.87 [Alarm E-Mail] window TABLE 1.123 Setting and display items in the [Alarm E-Mail] window TABLE 1.124 Buttons in the [Alarm E-Mail] window [Alarm E-Mail Filtering Condition] window Page TABLE 1.125 Setting and display items in the [Alarm E-Mail Filtering Con dition] window TABLE 1.126 Buttons in the [Alarm E-Mail Filtering Condition] window 1.6 [Maintenance] Menu 1.6.1 [Firmware Update] menu [Unified Firmware Update] window FIGURE 1.90 [Unified Firmware Update] window 1.6.2 [Backup/Restore Configuration] menu [Backup/Restore MMB Configuration] window FIGURE 1.91 Backup/Restore MMB Configuration window [Backup BIOS Configuration] window for PRIMEQUEST 2400E/2800E FIGURE 1.92 Backup BIOS Configuration window TABLE 1.127 Buttons in the [Backup BIOS Configuration] window [Restore BIOS Configuration] window for PRIMEQUEST 2400E/2800E FIGURE 1.93 [Restore BIOS Configuration] window (1) FIGURE 1.94 [Restore BIOS Configuration] window (2) TABLE 1.128 Setting and display items in the [Restore BIOS Configuration] window (2) TABLE 1.129 Buttons in the [Restore BIOS Configuration] window (2) [Backup/Restore BIOS Configuration] window for PRIMEQUEST 2800B FIGURE 1.95 Backup/Restore BIOS Configuration window 1.6.3 [Maintenance Wizard] window 1.6.4 [REMCS] menu 1.7 [System] Menu for PRIMEQUEST 2800B 1.7.1 [System Status] window FIGURE 1.96 [System Status] window TABLE 1.130 Status of Unit and its Icons 1.7.2 [System Event Log] Window FIGURE 1.97 [System Event Log] window TABLE 1.132 Items displayed in [System Event Log] Window Warning : Not a severe error, but an error is likely in future Info : Shows the information like Partition power ON TABLE 1.133 Buttons on [System Event Lo g] Window FIGURE 1.98 [System Event Log (Collect)] Window [System Event Log Filtering Condition] Window Page TABLE 1.135 [System Events Log Filtering Condition] Window Butto ns 1.7.3 [Operation Log] Window 1.7.4 [System Information] Window FIGURE 1.100 [System Information] Window Characters which can be entered: Alphanumeric characters, half-width space. The TABLE 1.137 Buttons on the [System Information] Window 1.7.5 [Firmware Information] Window FIGURE 1.101 [Firmware Information] Window TABLE 1.138 Display Item of [Firmware Information] Window MMB BMC BIOS MMB Not-present: It shows that Unit is not mounted. Gray color background is Major Version=1Byte data (Binary format) Minor Version=1Byte data (BCD format) 1.7.6 [System Setup] Window FIGURE 1.102 [System Setup] Window TABLE 1.139 Display Items and Setting Items in [System Setup] Window 100V 200V Single: primary power feed mode Dual: dual power feed mode Restore: Restores the status immediately before the power failure. If the Schedule Sync: If the partition is in the operating time zone, power of partition Redundant Non-redundant Enable Disable TABLE 1.140 [System Setup] window button 1.7.7 [Power Control] Window FIGURE 1.103 [Power Control] Window TABLE 1.141 Display Items and Set Items of [Power Control] Window TABLE 1.142 [Power Control] Window Buttons 1.7.8 [Schedule] Menu [Schedule Control] window FIGURE 1.104 [Schedule Control] Window TABLE 1.143 Display Items and Setting Items of [Schedule Control] W indow TABLE 1.144 [Schedule Control] Window Buttons [Schedule list] Window FIGURE 1.105 [Schedule List] Window TABLE 1.145 Display Items and Set Items of [Schedule List] W indow TABLE 1.146 [Schedule List] Window Buttons [Add Schedule] window/ [Edit Schedule] window FIGURE 1.106 [Schedule List] Window TABLE 1.147 Display Items and Set Items of [Add Schedule] Windo w TABLE 1.148 [Add Schedule] Window Buttons 1.7.9 [Console Redirection Setup] Menu [IPv4 Console Redirection Setup] window FIGURE 1.107 [IPv4 Console Redirection Setup] Window TABLE 1.149 Display Items and Set Items of [IPv4 Console redirection Set up] Window TABLE 1.150 [IPv4 Console redirection Setup] Window Buttons [IPv6 Console Redirection Setup] window FIGURE 1.108 [IPv6 Console Redirection Setup] Window TABLE 1.151 Display Items and Set Items of [IPv6 Console redirect ion Setup] Window TABLE 1.152 [IPv6 Console redirection Setup] Window Buttons 1.7.10 [Power Management Setup] Window FIGURE 1.109 [Power management Setup] window TABLE 1.153 Display Items and Set Items of [Power Management Setup] W indow TABLE 1.154 [Power Management Setup] Window Buttons 1.7.11 [ASR Control] Window FIGURE 1.110 [ASR (Automatic Server Restart) Control] Window TABLE 1.155 Display Items and Set Items of [ASR (Automatic Server Res tart) Control] Window TABLE 1.156 [ASR (Automatic Server Restart) Control] Window Buttons 1.7.12 [Console Redirection] Window FIGURE 1.111 [Console Redirection] Window TABLE 1.157 Display Items of [Console Redirection] Window 1.7.13 [Mode] Window FIGURE 1.112 [Mode] Window TABLE 1.158 Display Items and Setting Items in [Mode] W indow Page 1.7.14 [SB] Menu [SB#x] Window FIGURE 1.113 [SB#x] Window (1) Page Page Page Page Page Page Page TABLE 1.160 [SB#x] Window Button 1.7.15 [IOU] Menu [IOU#0] ~ [IOU#3] [IOU#x] Window FIGURE 1.119 [IOU#x] Window (1) Page TABLE 1.161 Display Items and Setting Items in [IOU#x] Window IOU_10GbE IOU_1GbE TABLE 1.162 Button of [IOB#x] Screen 1.7.16 [DU] Menu Page FIGURE 1.123 [MMB#x] Window(2) TABLE 1.163 Display of [MMB] Window / setting items TABLE 1.164 [MMB#x] Window button CHAPTER 2 MMB CLI (Command Line Interface) Operations 2.1 Basic Operations with the CLI 2.1.1 Access to the CLI via the serial interface TABLE 2.1 Terminal software setting values 2.1.2 Access via the management LAN interface 2.1.3 CLI command list TABLE 2.2 MMB CLI commands (Administrator) Page TABLE 2.3 MMB CLI commands (Operator) Page TABLE 2.4 MMB CLI commands (Partition Operator) Page Page TABLE 2.5 MMB CLI commands (User) Page TABLE 2.6 MMB CLI commands (CE) Page TABLE 2.7 Parameter specification range 2.2 Setting Commands 2.2.1 add partition 2.2.2 clear access_control 2.2.3 clear ssh _ key Privilege: User 2.2.4 console Privilege: Administrator, Operator 2.2.5 download ssh _key Privilege: User 2.2.6 power off Privilege: Administrator, Operator, Partition Operator (Partitions targeted for management only) 2.2.7 power on Page 2.2.8 sadump Privilege: Administrator, Operator, Partition Operator (Only the partit ion to be managed) 2.2.9 reset Privilege: Administrator, Operator, Partition Operator (Only the parti t i on to be managed) 2.2.10 nmi 2.2.11 remove partition 2.2.12 set active_mmb Privilege: Administrator, CE 2.2.13 set date 2.2.14 set partition dynamic_partitioning 2.2.15 set gateway 2.2.16 set gateway_ipv6 2.2.17 set hostname 2.2.18 set http 2.2.19 set http_port 2.2.20 set https 2.2.21 set https_port 2.2.22 set ip 2.2.23 set ipv6 2.2.24 set maintenance_ip Privilege: Administrator, CE 2.2.25 set partition home 2.2.26 set partition lan_device_mode 2.2.27 set partition memory_mirror_ras_mode 2.2.28 set partition memory_opration_mode Page 2.2.29 set partition name 2.2.30 set partition pci_address_mode 2.2.31 set ssh 2.2.32 set ssh_port 2.2.33 set telnet 2.2.34 set telnet_port 2.2.35 set timezone 2.2.36 hotadd partition Page 2.2.37 hotremove partition 2.3 Commands for Display 2.3.1 show access_control 2.3.2 show active_mmb 2.3.3 show date 2.3.4 show exit_code 2.3.5 show partition configuration 2.3.6 show partition dynamic_partitioning 2.3.7 show partition home 2.3.8 show partition lan_device_mode 2.3.9 show partition name 2.3.10 show partition memory_mirror_ras_mode 2.3.11 show partition memory_operation_mode 2.3.12 show partition pci_address_mode 2.3.13 show timezone 2.3.14 show gateway 2.3.15 show gateway_ipv6 2.3.16 show http 2.3.17 show http_port 2.3.18 show https 2.3.19 show https_port 2.3.20 show ip 2.3.21 show ipv6 2.3.22 show hostname 2.3.23 show maintenance_ip 2.3.24 show ssh 2.3.25 show ssh_port 2.3.26 show telnet 2.3.27 show telnet_port 2.3.28 show network 2.3.29 show ntpq TABLE 2.8 Output Items of show ntpq 2.3.30 who 2.3.31 help Page Page Page Page Page 2.3.32 netck traceroute 2.3.33 netck arptbl 2.3.34 netck arping 2.3.35 netck ifconfig 2.3.36 netck stat 2.3.37 show dynamic_partitioning status 2.4 Update Command 2.4.1 Update ALL Privilege: Administrator or CE 2.4.2 show update_status Privilege: Administrator or CE 2.5 Other Commands 2.5.1 exit 2.5.2 passwd 2.5.3 ping Page 2.6 PRIMEQUEST2800B model Commands 2.6.1 PRIMEQUEST2800B model CLI command list TABLE 2.9 MMB CLI commands (Administrator) TABLE 2.10 MMB CLI commands (Operator) TABLE 2.11 MMB CLI commands (User) TABLE 2.12 MMB CLI commands (CE) 2.6.2 power off 2.6.3 power on 2.6.4 reset 2.6.5 nmi 2.6.6 set memory_opration_mode Page 2.6.7 set memory_mirror_ras_mode 2.6.8 set lan_device_mode {quiet} 2.6.9 show memory_operation_mode 2.6.10 show memory_mirror_ras_mode 2.6.11 show lan_device_mode 2.6.12 set mmbcontrol reset 2.6.13 add user 2.6.14 show user_list Privilege: Administrator user_name privilege Aaaaaaaa Admin Cccccccccc Operator Dddddddd CE 2.6.15 console Privilege: Administrator, Operator, CE Page CHAPTER 3 UEFI Menu Operations 3.1 Front page of Boot Manager FIGURE 3.1 Display Example of Front page of Boot Manager 3.1.1 Window area FIGURE 3.2 Window area of Boot Manager Front Page TABLE 3.1 Display item of menu selection TABLE 3.2 Display Items on Operation Help Display 3.2 [Continue] Menu 3.3 [Boot Manager] Menu FIGURE 3.3 Display example of [Boot Manager] Menu 3.3.1 Boot Option TABLE 3.3 Initial state of Default 3.3.2 Boot specification of UEFI FIGURE 3.4 Boot Option of Boot Manager 3.3.3 About boot specification of legacy BIOS FIGURE 3.5 Execution of Legacy Boot Option 3.3.4 Boot processing TABLE 3.4 Flow of startup by boot specification of UEFI and boot specif ication of legacy BIOS TABLE 3.5 Boot success of Windows Server 2008 TABLE 3.6 Boot failure of Windows Server 2008 (UEFI Boot success of EFI USB Device) Page FIGURE 3.6 Example of displayed [Boot Manager] menu TABLE 3.9 Displayed contents of operation help display 3.4 [Device Manager] Menu FIGURE 3.7 Example of displayed [Device Manager] menu TABLE 3.10 Displayed contents of menu selection TABLE 3.11 Displayed contents of operation help display 3.4.1 [System Information] Menu FIGURE 3.8 Example of displaying [System Information] menu TABLE 3.12 Display Contents of the System Information Display TABLE 3.13 Display Contents of Help Operation Display 3.4.2 [I/O Space Assignment Configuration] Menu FIGURE 3.9 Display example of [I/O Space Assignment Configuration] Menu TABLE 3.14 Display Contents of Menu Selection TABLE 3.15 Display contents of Display of Operation help 3.4.3 [LAN Remote Boot Configuration] Menu TABLE 3.16 Reflection of [LAN Remote Boot Configuration] Menu FIGURE 3.10 Display of [LAN Remote Boot Configuration] Menu TABLE 3.17 Display contents of Menu Selection TABLE 3.18 Display contents of Display of Operation help FIGURE 3.11 Operation Window of PXE/iSCSI boot Enable Setting FIGURE 3.12 Display of [Boot Manager] Menu FIGURE 3.13 Display of [MAC Selection] FIGURE 3.14 Display of [Set Legacy Net Drive Order] Menu 3.4.4 [CPU Configuration] Menu FIGURE 3.15 Display Example of [CPU Configuration] Menu TABLE 3.19 Display Contents of Menu Selection Page TABLE 3.20 Display Contents of Operation Help Display 3.4.5 [PCI Bus Padding Configuration] Menu FIGURE 3.16 Example of Display on [PCI Bus Padding Configuration] Menu TABLE 3.21 Display Contents of Menu Selection TABLE 3.22 Display Contents of Operation Help Display 3.4.6 [PCI Subsystem Configuration] Menu FIGURE 3.17 Display Example on [PCI Subsystem Configuration] Menu TABLE 3.23 Display Contents of Menu Selection TABLE 3.24 Display Contents of Operation Help Display 3.4.7 [IOU OpROM Scan Configuration] Menu FIGURE 3.18 Display Example of [IOU OpROM Scan Configuration] Menu TABLE 3.25 Display Contents of Menu Selection Page TABLE 3.26 Display contents of operation help display 3.4.8 [PCI_Box OpROM Scan Configuration] menu FIGURE 3.19 Example of display of [PCI_Box OpROM Scan Configuration] menu TABLE 3.27 Display contents of menu selection Page Page Page Page TABLE 3.28 Display contents of operation help display 3.4.9 [iSCSI Configuration] menu Page TABLE 3.29 Display contents of Menu Selection TABLE 3.30 Display contents of Operation Help Display FIGURE 3.21 iSCSI Environment Setting Operation Windows (1) FIGURE 3.22 iSCSI Environment Setting Operation Windows (2) [MAC Selection] m enu. FIGURE 3.23 iSCSI Environment Setting Operation Windows (3) [Attempt Configur ation]menu 3.4.9.1 [MAC Selection] Menu FIGURE 3.24 Display example of [MAC Selection] menu TABLE 3.31 Display contents of menu selection TABLE 3.32 Display contents of operation help display 3.4.9.2 [Attempt Configuration] Menu FIGURE 3.25 Display example of [Attempt Configuration] Menu TABLE 3.33 Display contents of menu selection Page Page Page TABLE 3.34 Display contents of operation help display 3.4.9.3 [Delete Attempts] Menu FIGURE 3.26 Display example of [Delete Attempts] menu TABLE 3.35 Display contents of Menu selection TABLE 3.36 Display Contents of Operation Help Display 3.4.9.4 [Change Attempt Order] menu FIGURE 3.27 Display example of [Change Attempt Order] Menu TABLE 3.37 Display contents of Menu selection TABLE 3.38 Display Contents of Operation Help Display 3.4.10 [Memory Configuration] menu FIGURE 3.28 Display Example of [Memory Configuration] Menu TABLE 3.39 Display Contents of Menu Selection Page TABLE 3.40 Display Contents of Operation Help Display 3.4.11 [USB Configuration] menu FIGURE 3.29 Display example of [USB Configuration] menu TABLE 3.41 Display contents of Menu selection TABLE 3.42 Display Contents of Operation Help Display 3.4.12 [Security Configuration] menu FIGURE 3.30 Display Example of [Security Configuration] Menu TABLE 3.43 Display Contents of Menu Selection TABLE 3.44 Display contents of operation help display 3.5 [Boot maintenance Manager] Menu FIGURE 3.31 [Boot Maintenance manager] Menu TABLE 3.45 Display Contents of Menu Selection TABLE 3.46 Display Contents of Operation Help Display 3.5.1 [Boot Mode] Menu FIGURE 3.32 Example Display of [Boot Mode] Menu TABLE 3.47 Display Contents of Menu Selection Section TABLE 3.48 Display contents of operation help display 3.5.2 [Boot Options] menu FIGURE 3.33 [Boot options] menu TABLE 3.49 Display contents of Menu selection TABLE 3.50 Display contents of Display of operation help FIGURE 3.34 Display Example of [Boot Manager] Menu FIGURE 3.35 Display Example of [Add Boot Option] Menu TABLE 3.51 Display contents of Display of Operation help FIGURE 3.36 A list of Devices FIGURE 3.37 Display example of File Selection Window FIGURE 3.38 Windows Server 2012 Installed Disk Window FIGURE 3.39 Display Example of Boot Option Name Change Window FIGURE 3.40 Display Example of [Boot Manager] Menu TABLE 3.52 Number of Characters and Types of Characters that can be ent ered FIGURE 3.41 Display example of [Delete Boot option] menu TABLE 3.53 Display contents of operation help display FIGURE 3.42 Delete window (1) of boot option FIGURE 3.43 Boot Option Deletion Window (2) FIGURE 3.44 [Change Boot Order] Menu TABLE 3.54 Display Contents of Menu Selection TABLE 3.55 Display Contents of Operation Help Display TABLE 3.56 Display Contents of Operation Help Display when Pop-up W indow appears FIGURE 3.45 Change Window of Priority Order (Change Boot Order) (1) FIGURE 3.46 Change Window of Priority Order (Change Boot Order) (2) FIGURE 3.47 Windows after setting of priority level is changed (Change Boot Ord er) (3) FIGURE 3.48 Display example of [Set Legacy Floppy Drive Order] menu TABLE 3.57 Display contents of menu selection TABLE 3.58 Display contents of operation help display TABLE 3.59 Display Contents of operation help display when pop-up windo w appears FIGURE 3.49 Change in priority level (Set Legacy Floppy Drive Order) (1) FIGURE 3.50 Change in priority level (Set Legacy Floppy Drive Order) (2) FIGURE 3.51 Change of priority level (Set Legacy Floppy Drive Order) (3) FIGURE 3.52 Change of the priority level (Set Legacy Floppy Drive Order) (4) FIGURE 3.53 Display Example of [Set Legacy HardDisk Drive Order] Menu TABLE 3.60 Display Contents of Menu Selection TABLE 3.61 Display Contents of the Operation Help Display TABLE 3.62 Display Contents of the Operation Help Display when P op-up Window appears FIGURE 3.54 Change of the Priority Level (Set Legacy HardDisk Drive Order) (1) FIGURE 3.55 Change in Priority Level (Set Legacy HardDisk Drive Order) (2) FIGURE 3.56 Change in Priority Level (Set Legacy HardDisk Drive Order) (3) FIGURE 3.57 Change in Priority Level (Set Legacy HardDisk Drive Order) (4) FIGURE 3.58 Example of Displayed [Set Legacy CDROM Drive Order] Menu TABLE 3.63 Displayed Contents of Menu Selection TABLE 3.64 Display Contents of Operation Help Display TABLE 3.65 Display Contents of Operation Help Display when Pop-up Window appears FIGURE 3.59 Change in priority level (Set Legacy CD-ROM Drive Order (1) FIGURE 3.60 Change in priority level (Set Legacy CD-ROM Drive Order (2) FIGURE 3.61 Change in priority level (Set Legacy CD-ROM Drive Order) (3) FIGURE 3.62 Change in priority level (Set Legacy CD-ROM Drive Order) (4) FIGURE 3.63 Display example of the [Set Legacy NET Drive Order] menu TABLE 3.66 Display contents of menu selection TABLE 3.67 Display content of Operation Help Display TABLE 3.68 Display Content of Operation Help Display When Pop up W indow Appears FIGURE 3.64 Change (Set Legacy NET Drive Order) (1) of priority level FIGURE 3.65 Change of Priority Level (Set Legacy NET Drive Order) (2) FIGURE 3.66 Change of Priority Level (Set Legacy NET Drive Order) (3) FIGURE 3.67 Change of Priority Level (Set Legacy NET Drive Order) (4) 3.5.3 [Boot From File] Menu FIGURE 3.68 Display Example of [Boot From File] Menu TABLE 3.69 Display Contents of Operation Help Display FIGURE 3.69 Specifications of Boot File (1) Page 3.5.4 [Set Time out Value] Menu FIGURE 3.72 Logo Window FIGURE 3.73 Display Example of [Set Time out Value] Menu TABLE 3.70 Display Content of Menu Selection Help Display TABLE 3.71 Display Contents of Operation Help Display TABLE 3.72 Content of Operation Helps Display when Pop -up Windo w appears 3.6 Device Path 3.6.1 Parameter of Device Path TABLE 3.73 Parameter of Device Path 3.6.2 Identification of Device Path FIGURE 3.74 Specification of SAS disk built in SB FIGURE 3.75 Specification of SAS Disk built in DU#0 FIGURE 3.76 Specification of Disk from Fibre Card FIGURE 3.77 Specification of GigaLAN CHAPTER 4 UEFI Command Operations 4.1 Automatic startup file FIGURE 4.1 Sample screenshot of the UEFI shell immediately after it starts 4.1.1 Automatic startup file 4.1.2 UEFI shell command syntax TABLE 4.1 Wildcard characters in the UEFI shell ? * 4.1.3 Output redirection 4.1.4 UEFI shell command list TABLE 4.3 UEFI shell commands CHAPTER 5 Dynamic Reconfiguration Operation 5.1 DR Command 5.1.1 dr command (common part) 5.1.1.1 Synopsis 5.1.3 Show slot status (slot subcommand) 5.1.3.1 Synopsis 5.1.3.2 Description 5.1.3.3 Options 5.1.3.4 Example 5.1.4 Show resources on device (show subcommand) 5.1.4.1 Synopsis 5.1.4.2 Description 5.1.4.3 Options 5.1.4.4 Example 5.2 Hot plug collaboration function 5.2.1 Description of collaboration function 5.2.2 Collaboration program execution timing 5.2.3 Timeout of collaboration program 5.2.4 Directory that stored collaboration program 5.2.5 Naming convention of collaboration program 5.2.6 Method of describing configuration file of collaboration program 5.2.7 Permission required for collaboration program 5.2.8 Argument passed to collaboration program Page 5.2.9 Exit status of collaboration program 5.2.10 Output of collaboration program 5.2.11 Flow of collaboration program execution Page Page Page Page 6.1 Sadump Configuration Menu Page Page Page 6.1.1 Screen areas FIGURE 6.4 Screen areas of sadump configuration Help display area for operations Help display area 6.2 Main menu for menu selection FIGURE 6.5 Main menu TABLE 6.1 Displayed contents of the menu selection area TABLE 6.2 Displayed contents of the help display area for operation 6.3 [Set up Manager] Menu FIGURE 6.6 sadump setup menu TABLE 6.3 Displayed contents of the menu selection area TABLE 6.4 Displayed contents of the help display area for operation 6.4 [Dump device Manager] Menu FIGURE 6.7 Dump device maintenance menu TABLE 6.5 Displayed contents of menu selection area TABLE 6.6 Displayed contents of the help display area for operation 6.5 [Create a dump device] Menu FIGURE 6.8 Dump device create menu TABLE 6.7 Displayed contents of menu selection area TABLE 6.8 Displayed contents of the help display area for operation 6.6 [Select device] Menu FIGURE 6.9 Dump device select menu TABLE 6.9 Displayed contents of menu selection area TABLE 6.10 Displayed contents of the help display area for operation 6.7 [Setting dump device] Menu FIGURE 6.10 [Setting dump device] Menu TABLE 6.11 Displayed contents of the menu selection area 6.8 [Select device] Menu FIGURE 6.11 [Select device] Menu TABLE 6.13 Displayed contents of menu selection area TABLE 6.14 Displayed contents of the help display area for operation 6.9 [Select discard dump device] Menu FIGURE 6.12 [Select discard dump device] Menu TABLE 6.15 Displayed contents of menu selection area TABLE 6.16 Displayed contents of the help display area for operation 6.10 [Select multiple devices] Menu FIGURE 6.13 [Select discard dump device] Menu [Select multiple devices] Menu TABLE 6.17 Displayed contents of menu selection area TABLE 6.18 Displayed contents of the help display area for operation FIGURE 6.14 [Confirmation] Menu TABLE 6.19 Displayed contents of menu selection area TABLE 6.20 Displayed contents of the help display area for operation A.1 Setting Items of MMB Web-UI A.1.1 Setting items of [System Event Log Filtering Condition] Window TABLE A.1 Setting item of [System Event Log Filtering Condition] W indow A.1.2 Setting Item of [Operation Log Filtering Condition] Window TABLE A.2 Setting Items of [Operation Log Filtering Condition] Window A.1.3 Setting Items of [System Information] Window TABLE A.3 Setting Items of [System Information] Windo w A.1.4 Setting items of [System Setup] Window TABLE A.4 Setting items of [System Setup] Window A.1.5 Setting items of [System Power Control] Window TABLE A.5 Setting Items of [System Power Control] Window A.1.6 Setting items of [Power Control] Window TABLE A.6 Setting Items of [Power Control] Window A.1.7 Setting Items of [Schedule Control] Window TABLE A.7 Setting Items of [Schedule Control] Window A.1.8 Setting Items of [Add Schedule]/ [Edit User] Window TABLE A.8 Setting Items of [Add Schedule]/ [Edit User] Window A.1.9 Setting Items of [Partition Configuration] Window A.1.10 Setting Items of [IPv4 Console Redirection Setup] Window TABLE A.10 Setting Items of [IPv4 Console Redirection Setup] W indow A.1.11 Setting Items of [IPv6 Console Redirection Setup] Window TABLE A.11 Setting Items of [IPv6 Console Redirection Setup] W indow A.1.12 Setting Items of [Power Management Setup] Window A.1.13 Setting Items of [ASR Control] Window TABLE A.13 Setting Items of [ASR Control] Window A.1.14 Setting Items of [Console Redirection] Window TABLE A.14 Setting Items of [Console Redirection] Window A.1.15 Setting Items of [Mode] Window TABLE A.15 Setting Items of [Mode] Window A.1.16 Setting Items of [Add User]/ [Edit User] Window TABLE A.16 Setting Items of [Add User]/ [Edit User] Window A.1.17 Setting Items of [Date/Time] Window TABLE A.17 Setting Items of [Date/Time] Window A.1.18 Setting Items of [IPv4 Interface] Window TABLE A.18 Setting Items of [IPv4 Interface] Window A.1.19 Setting Items of [IPv6 Interface] Window TABLE A.19 Setting Items of [IPv6 Interface] Window A.1.20 Setting Items of [Management LAN Port Configuration] Window TABLE A.20 Setting Items of [Management LAN Port Configuration] W indow A.1.21 Setting Items of [Network Protocols] Window TABLE A.21 Setting Items of [Network Protocols] Window A.1.22 Setting Items of [Refresh Rate] Window TABLE A.22 Setting Items of [Refresh Rate] Window A.1.23 Setting Items of [SNMP Community] Window TABLE A.23 Setting Items of [SNMP Community] Wi ndow A.1.24 Setting Items of [SNMP Trap] Window TABLE A.24 Setting Items of [SNMP Trap] Window A.1.25 Setting Items of [SNMP v3 Configuration] Window TABLE A.25 Setting Items of [SNMP v3 Configuration] W indow A.1.26 Setting Items of [Create CSR] Window TABLE A.26 Setting Items of [Create CSR] Window A.1.27 Setting Items of [Create Selfsigned Certificate] Window TABLE A.27 Setting Items of [Create Selfsigned Certificate] W indow A.1.28 Setting Items of [Edit User] Window TABLE A.28 Setting Items of [Edit User] Window A.1.29 Setting Items of [Add Filter] / [Edit Filter] Window TABLE A.29 Setting Items of [Add Filter] / [Edit Filter ] Window A.1.30 Setting Items of [Alarm E-Mail] Window A.2 Setting Items on UEFI A.2.1 Setting Items on [I/O Space Assignment Configura ti on] Window TABLE A.32 Setting Items of [I/O Space Assignment Configuration] W indow A.2.2 Setting Items on [LAN Remote Boot Configuration] Window TABLE A.33 Setting Items of [LAN Remote Boot Configuration] W indow A.2.3 Setting Items on [CPU Configuration] Window Page A.2.4 Setting Items on [PCI Bus Padding Configuration] Window TABLE A.35 Setting Items of [PCI Bus Padding Configuration] W indow A.2.5 Setting Items on [PCI Subsystem Configuration] Window TABLE A.36 Setting Items of [PCI Subsystem Configuration] W indow A.2.6 Setting Items on [IOU OpROM Scan Configuration] Window A.2.7 Setting Items on [PCI_Box OpROM Scan Configuration] Window TABLE A.38 Setting Items of [PCI_Box OpROM Scan Configuration] Window Page A.2.8 Setting Items on [iSCS Configuration] Window TABLE A.39 Setting Items of [iSCS Configuration] W indow A.2.9 Setting Items on [Attempt Configuration] Window TABLE A.40 Setting Items of [Attempt Configuration] Window A.2.10 Setting Items on [Memory Configuration] Window TABLE A.41 Setting Items of [Memory Configuration] Window A.2.11 Setting Items on [USB Configuration] Window TABLE A.42 Setting Items of [USB Configuration] Wind ow A.2.12 Setting Items on [Security Configuration] Window A.3 Setting Items on Video redirection A.3.1 Setting Items on [Video] Window TABLE A.44 Setting Items of [Video] Window A.3.2 Setting Items on [Keyboard] Window TABLE A.45 Setting Items of [Keyboard] Window A.3.3 Setting Items on [Mouse] Window A.3.4 Setting Items on [Options] Window TABLE A.47 Setting Items of [Options] Window