Manuals / Fujitsu / Computer Equipment / Scanner

Fujitsu M3093GX, M3093EX manual SCSI-ID Setting, 1 SCSI-ID setting .1 SCSI-ID setting

Models: M3093GX M3093EX

1 50

Download 50 pages 25 Kb

Page 19

3.5 SCSI-ID Setting

3.5 SCSI-ID Setting

Use the address switches to set the device address. After the setting turn the power on.

Address switch

Interface connector

Interface cable

Figure 3.1 SCSI-ID setting

Table 3.1 SCSI-ID setting

ID

Contents

0 to 7

Available

8, 9

No Operation

*When the scanner is terminated device, the termination connector must be connected on one side of the connectors.

3 – 6

Image 19

Fujitsu M3093GX, M3093EX manual SCSI-ID Setting, 1 SCSI-ID setting .1 SCSI-ID setting

Contents

C150-E022-05EN M3093EX AND M3093GX IMAGE SCANNER OPERATOR’S GUIDEDate published REVISION RECORDRevised contents EditionConventions COMPONENTS CONTENTSCHAPTER 3 INSTALLATION AND CONNECTIONS MAINTENANCETROUBLESHOOTING Cleaning the document cover, document holding pad, and document bed FIGURESLED at an error TABLESSCSI-ID setting Installation specificationsTable 1.1 The differences between the M3093EX and the M3093GX CHAPTER 1 PREFACEThis page is intentionally left blank 2.1 Checking the Components CHAPTER 2 COMPONENTS2.2.1 Exterior view of image scanner 2.2 Part Names and FunctionsFigure 2.2 M3093EX/GX parts names Presses a document to the document bed 2.2.2 Functions of each partFigure 2.3 M3093EX/GX Indicators 2.3.1 Indicators 2.3 Indicator Functions3.1 Precautions CHAPTER 3 INSTALLATION AND CONNECTIONS3.2 Removing the Carrier Fixing Bracket 3.3 Connections Page 3.4 Mounting the Stacker Figure 3.1 SCSI-ID setting Table 3.1 SCSI-ID setting 3.5 SCSI-ID SettingCHAPTER 4 OPERATIONS 4.1 Turning on the Power4.2.1 Reading a standard-size document 4.2 Reading a Document in Flatbed Mode3 Do not move the document during the read operation Figure 4.1 Flatbed reading4.2.2 Reading a page from a thick book To read a page from a thick book, remember the following pointsFigure 4.2 Removing the document cover 4.2.3 Reading a document larger than the document board4.3 Reading Documents in ADF Mode Section A enlargerd Figure 4.3 ADF paper chute setting A4 or letter size or smaller 4 mm or less 6 Angling the documents Figure 4.4 Loading the document This page is intentionally left blank 5.1 Removing Jammed Documents CHAPTER 5 MAINTENANCE5.2 Notes on Daily Use 5.3 CleaningPick spring 5.3.2 Cleaning the ADFFigure 5.3 Cleaning the ADF Ejection roller Clean the roller on the opposite side also5.4.1 Parts number and replacement cycle 5.4 Consumables / Periodical replacement parts5.4.2 Replacing pad ASY 5.4.3 Replacing pick roller Figure 5.4 Pick Roller replacementPage CHAPTER TROUBLESHOOTINGTable 6.1 Check items Paper double feed Table 6.1 Check items continuedAPPENDIX A A.1 Installation SpecificationsFigure A.1 External dimensions A.2 External DimensionsAPPENDIX B B.1 Test mode for maintenanceTable B.1 LED at an error APPENDIX C C.2 IPC-2/CMP-2 option board installationC.1 Option 7 Remove the cover from the interface PCA 8 Connect the IPC-2 option board connector and tighten the screwScrew A Interface connector screw 5 Remove the two screws in the following figureScrew for memor board or CMP-2 M3093GX Screw for IPC-2IPC-2 option board CMP-2 option board or memory PCA M3093GX not shownThis page is intentionally left blank Page Page Page Reader Comment Form What is your overall rating of this publication?