Manuals / Fujitsu / Computer Equipment / Scanner

Fujitsu M3093EX, M3093GX manual Replacing pick roller, 4 Pick Roller replacement

Models: M3093GX M3093EX

1 50

Download 50 pages 25 Kb

Page 34

5.4.3Replacing pick roller

3Insert the pad assembly into the ADF frame hole (the bigger one), slide the assembly to the direction of the arrow until it clicks.

ADF frame

Pad assy

NOTICE: Pad can be replaced by aligning the holes of the pad with the pins of the Pad holder.

5.4.3Replacing pick roller

Replace the pickroller as follows.

Pad holder

Pad

Pick spring

Thumb Screw

Guide A

a.Pull the cap up to open the ADF unit.

b.Remove two thumb screws shown in Figure 5.4. And re- move the Guide A.

Thumb Screw

Figure 5.4 Pick Roller replacement

5 – 5

Image 34

Fujitsu M3093EX, M3093GX manual Replacing pick roller, 4 Pick Roller replacement

Contents

M3093EX AND M3093GX IMAGE SCANNER OPERATOR’S GUIDE C150-E022-05ENEdition REVISION RECORDRevised contents Date publishedConventions MAINTENANCE CONTENTSCHAPTER 3 INSTALLATION AND CONNECTIONS COMPONENTSTROUBLESHOOTING FIGURES Cleaning the document cover, document holding pad, and document bedInstallation specifications TABLESSCSI-ID setting LED at an errorCHAPTER 1 PREFACE Table 1.1 The differences between the M3093EX and the M3093GXThis page is intentionally left blank CHAPTER 2 COMPONENTS 2.1 Checking the Components2.2.1 Exterior view of image scanner 2.2 Part Names and FunctionsFigure 2.2 M3093EX/GX parts names 2.2.2 Functions of each part Presses a document to the document bed2.3 Indicator Functions Figure 2.3 M3093EX/GX Indicators 2.3.1 IndicatorsCHAPTER 3 INSTALLATION AND CONNECTIONS 3.1 Precautions3.2 Removing the Carrier Fixing Bracket 3.3 Connections Page 3.4 Mounting the Stacker 3.5 SCSI-ID Setting Figure 3.1 SCSI-ID setting Table 3.1 SCSI-ID setting4.1 Turning on the Power CHAPTER 4 OPERATIONS4.2 Reading a Document in Flatbed Mode 4.2.1 Reading a standard-size documentTo read a page from a thick book, remember the following points Figure 4.1 Flatbed reading4.2.2 Reading a page from a thick book 3 Do not move the document during the read operation4.2.3 Reading a document larger than the document board Figure 4.2 Removing the document cover4.3 Reading Documents in ADF Mode Section A enlargerd Figure 4.3 ADF paper chute setting A4 or letter size or smaller 4 mm or less 6 Angling the documents Figure 4.4 Loading the document This page is intentionally left blank CHAPTER 5 MAINTENANCE 5.1 Removing Jammed Documents5.3 Cleaning 5.2 Notes on Daily UseEjection roller Clean the roller on the opposite side also 5.3.2 Cleaning the ADFFigure 5.3 Cleaning the ADF Pick spring5.4.1 Parts number and replacement cycle 5.4 Consumables / Periodical replacement parts5.4.2 Replacing pad ASY Figure 5.4 Pick Roller replacement 5.4.3 Replacing pick rollerPage CHAPTER TROUBLESHOOTINGTable 6.1 Check items Table 6.1 Check items continued Paper double feedA.1 Installation Specifications APPENDIX AA.2 External Dimensions Figure A.1 External dimensionsB.1 Test mode for maintenance APPENDIX BTable B.1 LED at an error APPENDIX C C.2 IPC-2/CMP-2 option board installationC.1 Option 5 Remove the two screws in the following figure 8 Connect the IPC-2 option board connector and tighten the screwScrew A Interface connector screw 7 Remove the cover from the interface PCACMP-2 option board or memory PCA M3093GX not shown Screw for IPC-2IPC-2 option board Screw for memor board or CMP-2 M3093GXThis page is intentionally left blank Page Page Page What is your overall rating of this publication? Reader Comment Form