Manuals
/
Fujitsu
/
Computer Equipment
/
Scanner
Fujitsu
M3093EX, M3093GX manual
Models:
M3093GX
M3093EX
1
46
50
50
Download
50 pages
25 Kb
43
44
45
46
47
48
49
50
<
>
Troubleshooting
Specs
Install
Consumables / Periodical replacement parts
Dimension
Maintenance
Table B.1 LED at an error
SCSI-ID Setting
Cleaning the document cover, document holding pad, and document bed
Indicator Functions
Page 46
Image 46
Page 45
Page 47
Page 46
Image 46
Page 45
Page 47
Contents
M3093EX AND M3093GX IMAGE SCANNER OPERATOR’S GUIDE
C150-E022-05EN
Edition
REVISION RECORD
Revised contents
Date published
Conventions
MAINTENANCE
CONTENTS
CHAPTER 3 INSTALLATION AND CONNECTIONS
COMPONENTS
TROUBLESHOOTING
FIGURES
Cleaning the document cover, document holding pad, and document bed
Installation specifications
TABLES
SCSI-ID setting
LED at an error
CHAPTER 1 PREFACE
Table 1.1 The differences between the M3093EX and the M3093GX
This page is intentionally left blank
CHAPTER 2 COMPONENTS
2.1 Checking the Components
2.2.1 Exterior view of image scanner
2.2 Part Names and Functions
Figure 2.2 M3093EX/GX parts names
2.2.2 Functions of each part
Presses a document to the document bed
2.3 Indicator Functions
Figure 2.3 M3093EX/GX Indicators 2.3.1 Indicators
CHAPTER 3 INSTALLATION AND CONNECTIONS
3.1 Precautions
3.2 Removing the Carrier Fixing Bracket
3.3 Connections
Page
3.4 Mounting the Stacker
3.5 SCSI-ID Setting
Figure 3.1 SCSI-ID setting Table 3.1 SCSI-ID setting
4.1 Turning on the Power
CHAPTER 4 OPERATIONS
4.2 Reading a Document in Flatbed Mode
4.2.1 Reading a standard-size document
To read a page from a thick book, remember the following points
Figure 4.1 Flatbed reading
4.2.2 Reading a page from a thick book
3 Do not move the document during the read operation
4.2.3 Reading a document larger than the document board
Figure 4.2 Removing the document cover
4.3 Reading Documents in ADF Mode
Section A enlargerd
Figure 4.3 ADF paper chute setting
A4 or letter size or smaller 4 mm or less 6 Angling the documents
Figure 4.4 Loading the document
This page is intentionally left blank
CHAPTER 5 MAINTENANCE
5.1 Removing Jammed Documents
5.3 Cleaning
5.2 Notes on Daily Use
Ejection roller Clean the roller on the opposite side also
5.3.2 Cleaning the ADF
Figure 5.3 Cleaning the ADF
Pick spring
5.4.1 Parts number and replacement cycle
5.4 Consumables / Periodical replacement parts
5.4.2 Replacing pad ASY
Figure 5.4 Pick Roller replacement
5.4.3 Replacing pick roller
Page
CHAPTER
TROUBLESHOOTING
Table 6.1 Check items
Table 6.1 Check items continued
Paper double feed
A.1 Installation Specifications
APPENDIX A
A.2 External Dimensions
Figure A.1 External dimensions
B.1 Test mode for maintenance
APPENDIX B
Table B.1 LED at an error
APPENDIX C
C.2 IPC-2/CMP-2 option board installation
C.1 Option
5 Remove the two screws in the following figure
8 Connect the IPC-2 option board connector and tighten the screw
Screw A Interface connector screw
7 Remove the cover from the interface PCA
CMP-2 option board or memory PCA M3093GX not shown
Screw for IPC-2
IPC-2 option board
Screw for memor board or CMP-2 M3093GX
This page is intentionally left blank
Page
Page
Page
What is your overall rating of this publication?
Reader Comment Form