Manuals / Fujitsu / Computer Equipment / Scanner

Fujitsu M3093EX, M3093GX manual Connections

Models: M3093GX M3093EX

1 50

Download 50 pages 25 Kb

Page 16

3.3 Connections

3.3 Connections

Connect the image scanner using the following procedure.

1Set the power switch to off.

Power switch

2Connect the power cable.

Connect the power cable to the power inlet on the back of the image scanner. Connect the other end of the power cable to a power outlet.

Power outlet

for North America

Power inlet

Power cable

for Europe

3Connect the interface cables (for M3093EX).

Connect the interface cables to the interface connectors and fasten the cables with catches and screws as shown below.

Connect the other end of each interface cable to the host computer.

Back of the image scanner

Catches

Interface cable for video

Interface cable for RS232C

Screws

To the host system

3 – 3

Image 16

Fujitsu M3093EX, M3093GX manual Connections

Contents

M3093EX AND M3093GX IMAGE SCANNER OPERATOR’S GUIDE C150-E022-05ENREVISION RECORD Revised contentsEdition Date publishedConventions CONTENTS CHAPTER 3 INSTALLATION AND CONNECTIONSMAINTENANCE COMPONENTSTROUBLESHOOTING FIGURES Cleaning the document cover, document holding pad, and document bedTABLES SCSI-ID settingInstallation specifications LED at an errorCHAPTER 1 PREFACE Table 1.1 The differences between the M3093EX and the M3093GXThis page is intentionally left blank CHAPTER 2 COMPONENTS 2.1 Checking the Components2.2.1 Exterior view of image scanner 2.2 Part Names and FunctionsFigure 2.2 M3093EX/GX parts names 2.2.2 Functions of each part Presses a document to the document bed2.3 Indicator Functions Figure 2.3 M3093EX/GX Indicators 2.3.1 IndicatorsCHAPTER 3 INSTALLATION AND CONNECTIONS 3.1 Precautions3.2 Removing the Carrier Fixing Bracket 3.3 Connections Page 3.4 Mounting the Stacker 3.5 SCSI-ID Setting Figure 3.1 SCSI-ID setting Table 3.1 SCSI-ID setting4.1 Turning on the Power CHAPTER 4 OPERATIONS4.2 Reading a Document in Flatbed Mode 4.2.1 Reading a standard-size documentFigure 4.1 Flatbed reading 4.2.2 Reading a page from a thick bookTo read a page from a thick book, remember the following points 3 Do not move the document during the read operation4.2.3 Reading a document larger than the document board Figure 4.2 Removing the document cover4.3 Reading Documents in ADF Mode Section A enlargerd Figure 4.3 ADF paper chute setting A4 or letter size or smaller 4 mm or less 6 Angling the documents Figure 4.4 Loading the document This page is intentionally left blank CHAPTER 5 MAINTENANCE 5.1 Removing Jammed Documents5.3 Cleaning 5.2 Notes on Daily Use5.3.2 Cleaning the ADF Figure 5.3 Cleaning the ADFEjection roller Clean the roller on the opposite side also Pick spring5.4.1 Parts number and replacement cycle 5.4 Consumables / Periodical replacement parts5.4.2 Replacing pad ASY Figure 5.4 Pick Roller replacement 5.4.3 Replacing pick rollerPage CHAPTER TROUBLESHOOTINGTable 6.1 Check items Table 6.1 Check items continued Paper double feedA.1 Installation Specifications APPENDIX AA.2 External Dimensions Figure A.1 External dimensionsB.1 Test mode for maintenance APPENDIX BTable B.1 LED at an error APPENDIX C C.2 IPC-2/CMP-2 option board installationC.1 Option 8 Connect the IPC-2 option board connector and tighten the screw Screw A Interface connector screw5 Remove the two screws in the following figure 7 Remove the cover from the interface PCAScrew for IPC-2 IPC-2 option boardCMP-2 option board or memory PCA M3093GX not shown Screw for memor board or CMP-2 M3093GXThis page is intentionally left blank Page Page Page What is your overall rating of this publication? Reader Comment Form