Manuals / Fujitsu / Computer Equipment / Scanner

Fujitsu M3093EX, M3093GX manual Maintenance, Removing Jammed Documents

Models: M3093GX M3093EX

1 50

Download 50 pages 25 Kb

Page 30

CHAPTER 5 MAINTENANCE

CHAPTER 5 MAINTENANCE

5.1Removing Jammed Documents

5.2Notes on Daily Use

5.3Cleaning

5.4Consumables/Periodical replacement parts

This section explains how to remove jammed documents, and provides notes on daily use and cleaning.

5.1 Removing Jammed Documents

If documents jam while being fed by the ADF, remove the jammed documents as follows:

1Remove the documents from the ADF paper chute.

2Pulling up the ADF lever, open the automatic document feeder.

3Remove the jammed documents.

4Close the ADF until the ADF lever locks.

ADF lever

Automatic document feeder (ADF)

Figure 5.1 Removing jammed documents

5 – 1

Image 30

Fujitsu M3093EX, M3093GX manual Maintenance, Removing Jammed Documents

Contents

M3093EX AND M3093GX IMAGE SCANNER OPERATOR’S GUIDE C150-E022-05ENEdition REVISION RECORDRevised contents Date publishedConventions MAINTENANCE CONTENTSCHAPTER 3 INSTALLATION AND CONNECTIONS COMPONENTSTROUBLESHOOTING FIGURES Cleaning the document cover, document holding pad, and document bedInstallation specifications TABLESSCSI-ID setting LED at an errorCHAPTER 1 PREFACE Table 1.1 The differences between the M3093EX and the M3093GXThis page is intentionally left blank CHAPTER 2 COMPONENTS 2.1 Checking the Components2.2 Part Names and Functions 2.2.1 Exterior view of image scannerFigure 2.2 M3093EX/GX parts names 2.2.2 Functions of each part Presses a document to the document bed2.3 Indicator Functions Figure 2.3 M3093EX/GX Indicators 2.3.1 IndicatorsCHAPTER 3 INSTALLATION AND CONNECTIONS 3.1 Precautions3.2 Removing the Carrier Fixing Bracket 3.3 Connections Page 3.4 Mounting the Stacker 3.5 SCSI-ID Setting Figure 3.1 SCSI-ID setting Table 3.1 SCSI-ID setting4.1 Turning on the Power CHAPTER 4 OPERATIONS4.2 Reading a Document in Flatbed Mode 4.2.1 Reading a standard-size documentTo read a page from a thick book, remember the following points Figure 4.1 Flatbed reading4.2.2 Reading a page from a thick book 3 Do not move the document during the read operation4.2.3 Reading a document larger than the document board Figure 4.2 Removing the document cover4.3 Reading Documents in ADF Mode Section A enlargerd Figure 4.3 ADF paper chute setting A4 or letter size or smaller 4 mm or less 6 Angling the documents Figure 4.4 Loading the document This page is intentionally left blank CHAPTER 5 MAINTENANCE 5.1 Removing Jammed Documents5.3 Cleaning 5.2 Notes on Daily UseEjection roller Clean the roller on the opposite side also 5.3.2 Cleaning the ADFFigure 5.3 Cleaning the ADF Pick spring5.4 Consumables / Periodical replacement parts 5.4.1 Parts number and replacement cycle5.4.2 Replacing pad ASY Figure 5.4 Pick Roller replacement 5.4.3 Replacing pick rollerPage TROUBLESHOOTING CHAPTERTable 6.1 Check items Table 6.1 Check items continued Paper double feedA.1 Installation Specifications APPENDIX AA.2 External Dimensions Figure A.1 External dimensionsB.1 Test mode for maintenance APPENDIX BTable B.1 LED at an error C.2 IPC-2/CMP-2 option board installation APPENDIX CC.1 Option 5 Remove the two screws in the following figure 8 Connect the IPC-2 option board connector and tighten the screwScrew A Interface connector screw 7 Remove the cover from the interface PCACMP-2 option board or memory PCA M3093GX not shown Screw for IPC-2IPC-2 option board Screw for memor board or CMP-2 M3093GXThis page is intentionally left blank Page Page Page What is your overall rating of this publication? Reader Comment Form