Manuals / Fujitsu / Computer Equipment / Computer Drive

Fujitsu MAU3147NC/NP Power Supply Requirements, 8 Spin-up current waveform +12 VDC, MAU3073NC/NP

Models: MAU3036NC/NP MAU3147NC/NP MAU3073NC/NP

1 130

Download 130 pages 55.01 Kb

Page 58

4.2Power Supply Requirements

4.2Power Supply Requirements

(1)Allowable input voltage and current

The power supply input voltage measured at the power supply connector pin of the IDD (receiving end) must satisfy the requirement given in Subsection 2.1.3. (For other requirements, see Items (4) and (5) below.)

(2)Current waveform (reference)

Figure 4.8 shows the spin-up current waveform of +12 VDC.

	MAU3147NC/NP					MAU3073NC/NP				MAU3036NC/NP

Current (500mA/div)								Current (500mA/div)
Current (500mA/div)				Current (500mA/div)				Current (500mA/div)



		Time (2 sec/div)				Time (2 sec/div)				Time (2 sec/div)

Figure 4.8 Spin-up current waveform (+12 VDC)

(3)Power on/off sequence

a)The order of the power on/off sequence of +5 VDC and +12 VDC, supplied to the IDD, does not matter.

b)In a system which uses the terminating resistor power supply signal (TERMPWR) on the SCSI bus, the requirements for +5 VDC given in Figure 4.9 must be satisfied between the IDD and at least one of the SCSI devices supplying power to that signal.

Figure 4.9 Power on/off sequence (1)

4-8

C141-E205

Image 58

Fujitsu MAU3147NC/NP Power Supply Requirements, 8 Spin-up current waveform +12 VDC, 9 Power on/off sequence, MAU3073NC/NP

Contents

PRODUCT/MAINTENANCE MANUAL C141-E205-01ENMAU3147NC/NP MAU3073NC/NP MAU3036NC/NP DISK DRIVES IMPORTANT NOTE TO USERS Handling of This manualFOR SAFE OPERATION REVISION RECORD Specification No. C141-E205-**ENRelated Standards CHAPTER 4 INSTALLATION REQUIREMENTS PREFACECHAPTER 2 SPECIFICATIONS CHAPTER 5 INSTALLATIONCONVENTIONS FOR ALERT MESSAGES CONVENTIONS USED IN THIS MANUALImportant Alert Items Important Alert MessagesTask Specifications MANUAL ORGANIZATION PRODUCT MAINTENANCE MANUAL This manualSCSI Physical Interface Specifications SCSI Logical Interface 1. General Description 2. Specifications 3. Data FormatThis page is intentionally left blank INSTALLATION REQUIREMENTS CONTENTSSPECIFICATIONS CHAPTERCHAPTER 5 INSTALLATION CHAPTER 6 DIAGNOSTICS AND MAINTENANCEAPPENDIX B CONNECTOR SIGNAL ALLOCATION CHAPTER 7 ERROR ANALYSISAPPENDIX A SETTING TERMINALS INDEXFIGURES CN2 setting terminal on NP models only Output signal for external LEDSetting terminals location on NP models only Test flowchartTABLES CHAPTER 1 GENERAL DESCRIPTION 1.1 Standard Features 1.2 Hardware Structure 1.3 System Configuration1.1 Standard Features When Write cache is enabled, you should ensure that the cashed data is surely flushed to the disc media before you turn off the drives power 3. The Recoverable Error referred in 2 is sense data Error rate increase1. The drive format at factory shipment is generally 512 byte 16 Start/Stop of spindle motor 18 Low power consumption15 Large capacity 17 DiagnosisFigure 1.2 NP model drives outer view 1.2 Hardware StructureFigure 1.1 NC model drives outer view C141-E2053 Spindle motor 1 Disks2 Heads 4 ActuatorSCSI bus #14 #15 1.3 System ConfigurationFigure 1.3 System configuration C141-E2052 Addressing of peripheral device 1 SCSI bus configuration16-bit SCSISelectable from 0 to 15 switch selectable SCSI IDThis page is intentionally left blank 2.1 Hardware Specifications 2.1.1 Model name and order number CHAPTER 2 SPECIFICATIONS2.1 Hardware Specifications 2.2 SCSI Function Specifications Table 2.1 Model names and order numbersTrack to Track 2.1.2 Function specificationsFunction specifications Seek time *38 1 on 1 connection case 9 1 host, 15 devices case 2 1GB=1,000,000,000 bytes 3 The seek time is as follows Seek time msSeek Difference 4096 Cyl/div 11 1MB=1,048,576 bytes2.1.3 Environmental specifications Environmental/power requirements2.1.4 Error rate 2.1.5 ReliabilityStrengthen cooling power so that DE surface SCSI function specifications 2.2 SCSI Function Specifications4 Refer to 12 of Section This page is intentionally left blank 3.1 Data Space 3.2 Logical Data Block Addressing CHAPTER 3 DATA FORMAT3.1.1 Cylinder configuration 3.3 Defect ManagementFigure 3.1 Cylinder configuration 3.1.2 Alternate spare area Figure 3.2 Spare area in cell Figure 3.3 Alternate cylinderFigure 3.4 Track format 3.1.3 Track formatServo frame Figure 3.6 Sector format Figure 3.5 Track skew/head skew3.1.4 Sector format Track skew Head Track skew Head skew Head4 Data field DATA1-DATA4 1 Gaps G1, G2, G3 No pattern is written on the gap field 2 PLO Sync3 Sync Mark SM1, SM2 5 BCRCFormat capacity 3.1.5 Format capacity3.2 Logical Data Block Addressing 2 Alternate area 1 Block address of user spaceC141-E205 3.3 Defect Management 3.3.1 Defect list 3.3.2 Alternate block allocationC141-E205 1 Alternate block allocation during FORMAT UNIT command execution3-11 Figure 3.7 Alternate block allocation by FORMAT UNIT command Figure 3.8 Alternate block allocation by REASSIGN BLOCKS command Example Reassign Blockc SA and defect map update processing on alternate side Type 1 Reassignment of Uncorrectable Read Error1 Commands to be applied WRITE WRITE EXTEND Type 2 Reassignment of write fail sector 1 Commands to be appliedARRE = Twice AWRE Type 1 = Eight times This page is intentionally left blank 4.1 Mounting Requirements 4.1.1 External dimensions CHAPTER 4 INSTALLATION REQUIREMENTS4.1 Mounting Requirements 4.2 Power Supply Requirements 4.3 Connection RequirementsFigure 4.1 NC external dimensions C141-E205Figure 4.2 NP external dimensions C141-E2054.1.2 Mounting Figure 4.3 IDD orientations 4.1.3 Notes on mountingFigure 4.4 Mounting frame structure 5.0 or less 5.0 or lessHoles for Mounting screw Surface temperature check pointFigure 4.5 Limitation of side-mounting Holes for mounting screw Use four holes No.1 to No.4 to mountFigure 4.6 Surface temperature measurement points Figure 4.7 Service clearance areaFigure 4.8 Spin-up current waveform +12 VDC 4.2 Power Supply RequirementsFigure 4.9 Power on/off sequence MAU3073NC/NPSCSI devices with the terminating resistor Figure 4.10 Power on/off sequenceFigure 4.11 Power on/off sequence SCSI devices without noise leaking designed4 Sequential starting of spindle motors Delay time of spindle motor starting5 Power supply to SCSI terminating resistor SCSI IDSCSI connector CN1 including power supply 4.3.1 SCA2 connector type 16-bit SCSI model NC model1 Connectors Figure 4.13 NC connectors locationFigure 4.14 SCA2 type 16-bit SCSI connector 4.3.2 68-pin connector type 16-bit SCSI model NP model External operator panel connector CN2 Power supply Connector CN1connector CN1 Figure 4.15 NP connectors and terminals locationFigure 4.16 68-pin type 16-bit SCSI interface connector Figure 4.17 Power supply connector 68-pin type 16-bit SCSIFigure 4.18 External operator panel connector CN1 Figure 4.19 External operator panel connector CN24-16 5 External operator panel connector SignalsFigure 4.20 16-bit SCSI ID external input C141-E205This signal is temporarily driven at the GND level when the micro program reads the SCSI ID immediately after the power supply to the IDD has been switched on it is possible to set up the SCSI ID by short circuiting CN1-A1 and CN1-A2 4-18 Figure 4.21 Output signal for external LEDe. -WTP Input signal CN1-A12 and CN2-9, 10 pin C141-E205Figure 4.22 SCSI cables connection 6 Cable connection requirementsExternal operator panel example C141-E2054.3.3 Cable connector requirements Table 4.2 Recommended components for connection4.3.4 External operator panel on NP model drives only Figure 4.23 External operator panel circuit example4-22 C141-E2055.4 Mounting Drives 5.5 Connecting Cables CHAPTER 5 INSTALLATION5.1 Notes on Handling Drives 5.2 Connections 5.3 Setting Terminals 5.6 Confirming Operations after Installation and Preparation for Usec To prevent condensation, avoid sudden changes in temperature 3 Installation/removal/replacementd Keep a record of all maintenance work for replacing 4 Packaging 2 Unpackaging5.2 Connections Figure 5.1 SCSI bus connections 1 of 2 Connecting more than one IDD single host3 Connecting more than one IDD multi-host SCSI terminator Figure 5.1 SCSI bus connections 2 of5.3 Setting Terminals Figure 5.2 Setting terminals location on NP models onlyFigure 5.3 CN2 setting terminal on NP models only 5.3.1 SCSI ID settingSCSI ID setting Table 5.3 Motor start mode setting 5.3.2 Each mode settingTable 5.2 Setting SCSI terminator power supply NP model Supply onTable 5.5 Setting of the SCSI interface operation mode NP model Table 5.4 Write protect setting NP modelTable 5.6 Setting the bus width of the SCSI interface NP model 5.3.3 Mode settings Table 5.7 Default mode settings by CHANGE DEFINITION command5.4.2 Mounting procedures Setting check list NP model only5.4 Mounting Drives 5.4.1 Check before mounting 5.5 Connecting Cables 5.6.1 Confirming initial operations 5.6 Confirming Operations after Installation and Preparation for UseRemark 5.6.2 Checking SCSI connection Unit Of =1 Motor starts when power is turned onSelf test = No par ameter5-16 Motor starts by START/STOP command Executing time about 60 secondsFigure 5.5 Checking the SCSI connection B C141-E2055.6.3 Formatting a. Specifying CDB 2 FORMAT UNIT commandb. Format parameter page code = b. Format parameter5.6.4 Setting parameters continued ARRE AWRE TB PER Default valueAverage amount of processing data specified with a command 2 Disconnection/reconnection parameters page code =control page absolute value5.8 Spare Disk Drive 5.7 Dismounting Drivessequence of This page is intentionally left blank 6.4 Troubleshooting Procedures CHAPTER 6 DIAGNOSTICS AND MAINTENANCE6.1 Diagnostics 6.2 Maintenance Information 6.3 Operation Check 6.1 Diagnostics 6.1.1 Self-diagnosticsa. Hardware function test Brief test contents of self-diagnostics are as follows1 Initial self-diagnostics RAM microcode is stored Peripheral circuits of microprocessor MPUOperation of self-diagnostics 6.1.2 Test programs 6.2 Maintenance Information 6.2.1 Precautions 6.2.2 Maintenance requirements 3 Parts that can be replaced in the field 6.2.3 Maintenance levels 6.2.4 Revision numbers Figure 6.1 Revision label6.2.6 Tests Figure 6.2 Indicating revision numbers 6.2.5 Tools and test equipmentRevising at field Figure 6.3 Test flowchart 6.3 Operation Check 6.3.1 Initial seek operation check 6.3.3 Diagnostic test6.3.2 Operation test 6.4.1 Outline of troubleshooting procedures 6.4 Troubleshooting Procedures6.4.2 Troubleshooting with disk drive replacement in the field System-level field troubleshooting 6.4.3 Troubleshooting at the repair site Disk drive troubleshooting6.4.5 Finding possibly faulty parts 6.4.4 Troubleshooting with parts replacement in the factoryThis manual does not cover troubleshooting at the factory level 6-167.1 Error Analysis Information Collection 7.2 Sense Data Analysis CHAPTER 7 ERROR ANALYSIS7.1 Error Analysis Information Collection 7.1.1 Sense data Additional sense code Figure 7.1 Format of extended sense dataAdditional sense code qualifier Table 7.1 Definition of sense data 7.2.1 Error information indicated with sense data7.2 Sense Data Analysis Sense7.2.3 Sense data 1-1x-xx, 3-1x-xx and E-1D-00 Disk read error 7.2.2 Sense data 3-0C-03, 4-40-xx, and 4-C4-xxAPPENDIX A SETTING TERMINALS A.1 Setting Terminals on NP model onlyMotor start mode A.1 Setting Terminals on NP model onlyCN2 setting terminal on NP model drives only Table A.1B.1 SCSI Connector Signal Allocation SCA2 type LVD 16-bit SCSI APPENDIX B CONNECTOR SIGNAL ALLOCATIONB.2 SCSI Connector Signal Allocation 68-pin type LVD 16-bit SCSI Table B.1 SCSI connector SCA2 type LVD 16-bit SCSI CN1 B.1 SCSI Connector Signal Allocation SCA2 type LVD 16-bit SCSIC141-E205 SCSI Connector Signal Allocation 68-pin type LVD 16-bit SCSI Table B.2 SCSI connector 68-pin type LVD 16-bit SCSI CN1This page is intentionally left blank INDEX IN-2 C141-E205Page This page is intentionally left blank Comment Form This page is intentionally left blankw