Manuals / Fujitsu / Computer Equipment / Personal Computer

Fujitsu TX120 manual Indicators on the control panel

Models: TX120

1 82

Download 82 pages 63.94 Kb

Page 46

Controls and displays

Starting up and operation

Indicators on the control panel

Power-on indicator (dual color)

Lights orange when the server is switched off but mains voltage is present.

Lights up green when the server is switched on and ready.

Hard drive activity indicator (green)

Flashes green when an internal hard disk drive is being accessed.

Global Error indicator (red)

! Does not light up when the system is OK. No service incident or critical event has occurred.

Lights up red when a predictable error has been detected. Users can check the system and event log or via ServerView for more detailed information.

Flashes red when a critical event has occurred. Users can check for event details in the BIOS Setup, the system and event log or via ServerView.

If the event is still acute after a power failure, the indicator is activated after the restart.

ID ID indicator (blue)

Lights up blue when the system has been selected by pressing the ID button. To deactivate, press the button again.

The ID indicator can also be activated via ServerView and its status reported to ServerView.

46

Operating Manual

TX120

Image 46

Fujitsu TX120 manual Indicators on the control panel

Contents

Primergy TX120 Server Comments… Suggestions… Corrections… Certified documentation according to DIN EN ISOContents Contents Contents Page Introduction Documentation overviewConcept and target groups for this manual Documentation overviewAdditional server documentation Introduction Further sources of informationSystem board FeaturesFeatures Hard disk drivesUSB ports HDD expansion box and accessible drivesPower supply High level of availability and data securityIRMC with integrated service LAN port Server Management ServerStartService and support RemoteViewNotational conventions Electrical data Technical dataTechnical data Compliance with regulations and standardsUpright operating position WeightMechanical values Ventilation clearancePage Installation steps, overview Set up the server see section Setting up the server onInstallation steps, overview Safety Important informationInstallation and operation SafetyBefore starting up Important information Safety Batteries Laser information Working with CDs/DVDs and CD/DVD drivesNever remove parts of the CD/DVD drive casing Modules with Electrostatic-Sensitive Devices ESD labelCE conformity CE conformityFCC Class a Compliance Statement Other important informationTransporting the server Environmental protection Labels on plastic casing parts Returns, recycling and disposalPage Minimum acclimatization time Hardware installationHours Unpacking the server Unpacking the serverSetting up the server Hardware installationSetting up the server Clipping the stabilizers togetherAdjusting the width of the stabilizers Adjusting the width of a stabilizerPlacing the server on the stabilizers Placing the server on stabilizersPositioning the server horizontally Connecting devices to the server Connecting devices to the serverConnecting the server to the mains Connecting the server to the mainsConnecting cables Disconnecting cablesStarting up and operation Opening the drive coverControls and displays Controls and displaysStarting up and operation ControlsIndicators on the control panel CD/DVD indicator Indicators on the HDD moduleRear of server System already installed Switching the server on and offSwitching the server on Starting up for the first timeSpecified switch on time / switch off time Switching the server on and offSwitching the server OFF Ring indicatorConfiguring the server ServerStart advantagesConfiguring onboard SAS controller Cleaning the serverCleaning the server Operating system installationBios Setup security functions Mechanical access protectionProperty and data protection Page Power cable incorrectly connected Troubleshooting and tipsPower-on indicator remains unlit Power supply overloadedServer switches itself off Screen remains blankNo screen display or display drifts Troubleshooting and tipsFlickering stripes on monitor screen Monitor does not support the set horizontal frequencyIncorrect date and time Mouse driver not loaded Mouse controller disabledNo mouse pointer displayed on screen No mouse pointer displayed on screenRAID controller configuration incorrect Drives reported as dead when starting systemError message on screen RAID controller is not configured for this drivePage Hot-plug hard disk drives Handling hard disk drives and HDD modules Handling hard disk drives and HDD modulesRemoving/Installing the dummy module Removing the dummy moduleInstalling/Removing the HDD module Installing/Removing the HDD moduleUnlocking the HDD module Installing the HDD module Installing the HDD moduleRemoving the HDD module Vcaution Page Abbreviations Abbreviations ESD IRMC PS/2 Rtds Svga Page Literature Operating Manual Index CD-RWIndex DVDPDA Saving energy Screen