Manuals / Fujitsu / Computer Equipment / Personal Computer

Fujitsu TX120 manual Switching the server on and off, Starting up for the first time

Models: TX120

1 82

Download 82 pages 63.94 Kb

Page 49

Starting up and operation

Switching the server on and off

5.3Switching the server on and off

VCAUTION!

If nothing appears on the screen but flickering stripes after switching on the server, switch the server off immediately (see section “Flickering stripes on monitor screen” on page 57).

The On/Off button does not disconnect the server from the mains. To disconnect from the mains completely, remove the power plug(s).

Switching the server on

The power-on indicator (item 5 in figure 9 on page 44) lights orange.

–Starting up for the first time:

ÊPress the On/Off button (item 11 in figure 9 on page 44).

The power-on indicator lights up green (item 5 in figure 9 on page 44).

ÊInsert ServerStart disc 1 in the CD/DVD drive.

ÊFollow the on-screen instructions (see also section “Configuring onboard SAS controller” on page 51 or section “Configuration without Server- Start” on page 52).

–System already installed:

ÊPress the On/Off button (item 11 in figure 9 on page 44).

The power-on indicator lights up green (item 5 in figure 9 on page 44).

The server is switched on, performs a system test and boots the operating system.

TX120

Operating Manual

49

Image 49

Fujitsu TX120 manual Switching the server on and off, Starting up for the first time, System already installed

Contents

Primergy TX120 Server Certified documentation according to DIN EN ISO Comments… Suggestions… Corrections…Contents Contents Contents Page Documentation overview IntroductionConcept and target groups for this manual Documentation overviewAdditional server documentation Further sources of information IntroductionFeatures FeaturesSystem board Hard disk drivesPower supply HDD expansion box and accessible drivesUSB ports High level of availability and data securityIRMC with integrated service LAN port ServerStart Server ManagementRemoteView Service and supportNotational conventions Technical data Technical dataElectrical data Compliance with regulations and standardsMechanical values WeightUpright operating position Ventilation clearancePage Set up the server see section Setting up the server on Installation steps, overviewInstallation steps, overview Important information SafetyInstallation and operation SafetyBefore starting up Important information Safety Batteries Laser information Working with CDs/DVDs and CD/DVD drivesNever remove parts of the CD/DVD drive casing ESD label Modules with Electrostatic-Sensitive DevicesFCC Class a Compliance Statement CE conformityCE conformity Other important informationTransporting the server Environmental protection Returns, recycling and disposal Labels on plastic casing partsPage Minimum acclimatization time Hardware installationHours Unpacking the server Unpacking the serverHardware installation Setting up the serverClipping the stabilizers together Setting up the serverAdjusting the width of a stabilizer Adjusting the width of the stabilizersPlacing the server on stabilizers Placing the server on the stabilizersPositioning the server horizontally Connecting devices to the server Connecting devices to the serverConnecting the server to the mains Connecting the server to the mainsDisconnecting cables Connecting cablesOpening the drive cover Starting up and operationControls and displays Controls and displaysControls Starting up and operationIndicators on the control panel Indicators on the HDD module CD/DVD indicatorRear of server Switching the server on Switching the server on and offSystem already installed Starting up for the first timeSwitching the server OFF Switching the server on and offSpecified switch on time / switch off time Ring indicatorServerStart advantages Configuring the serverCleaning the server Cleaning the serverConfiguring onboard SAS controller Operating system installationBios Setup security functions Mechanical access protectionProperty and data protection Page Power-on indicator remains unlit Troubleshooting and tipsPower cable incorrectly connected Power supply overloadedScreen remains blank Server switches itself offFlickering stripes on monitor screen Troubleshooting and tipsNo screen display or display drifts Monitor does not support the set horizontal frequencyNo mouse pointer displayed on screen Mouse driver not loaded Mouse controller disabledIncorrect date and time No mouse pointer displayed on screenError message on screen Drives reported as dead when starting systemRAID controller configuration incorrect RAID controller is not configured for this drivePage Hot-plug hard disk drives Handling hard disk drives and HDD modules Handling hard disk drives and HDD modulesRemoving the dummy module Removing/Installing the dummy moduleInstalling/Removing the HDD module Installing/Removing the HDD moduleUnlocking the HDD module Installing the HDD module Installing the HDD moduleRemoving the HDD module Vcaution Page Abbreviations Abbreviations ESD IRMC PS/2 Rtds Svga Page Literature Operating Manual CD-RW IndexDVD IndexPDA Saving energy Screen