Manuals / Fujitsu / Computer Equipment / Switch

Fujitsu XG0224 manual Connecting Twisted Pair Cable, optical cable, Twisted pair cable

Models: XG0224

1 47

Download 47 pages 35.13 Kb

Page 37

optical cable

XG0224 Hardware Guide	Chapter 2 Installation

2.3.3Connecting Twisted Pair Cable / SFP Module / SFP+ Module / CX4 Cable

The following describes how to connect twisted pair cable, SFP module, SFP+ module, and CX4 cable.

Use straight cable when connecting with routers and terminals. Use crossing cable in case of cascading connection with other switching HUBs with transmission mode at fixed setting other than auto negotiation.

Straight cable

crossing cable

optical cable

Port of the switch is set auto negotiation enable by default.

(However, SFP+ Slots and CX4 port only support 10Gbps full duplex mode fixed setting.)

Ports automatically apply to the maximum speed that plugged equipment supports by the auto negotiation function.

•	10/100/1000BASE-T port	: Up to maximum 1000Mbps full duplex mode
•	SFP slot	: Up to maximum 1000Mbps full duplex mode

Connecting Twisted Pair Cable

Insert twisted pair cable to 10/100/1000BASE-T port until it clicks.

Twisted pair cable

Precautions

•In case of 1000BASE-T, usable twisted pair cables are unshielded twisted pair cable (UTP) over category 5E and shielded twisted pair cable (STP).

•RJ45 ports 21 through 24 are combination ports that are associated with the four SFP ports. Their use is mutually exclusive. If the RJ45 port 21 is cabled then the associated SFP slot cannot be used.

•Discharge twisted pair cable before connecting as twisted pair cable may be charged static electricity. Refer "2.3.1 Discharging Twisted Pair Cable" (pg.35) for discharging method.

37	Connecting the Equipment

Image 37

Fujitsu XG0224 manual Connecting Twisted Pair Cable, optical cable, Twisted pair cable

Contents

XG0224 TA41001-6348Hardware Guide Preface 4. Scope of Warranty LICENSE AGREEMENT1. Use and Copyright of the Software 2. TransferFUJITSU LIMITED 5. High Safety Required UseInstallation ContentsChapter Getting StartedContents Connecting to a Setup PCTime Setting Set up IP addressHint Precautions About the SymbolsOrganization and Usage of This Manual About This ManualAbbreviated Product Names Trademark Notification in This ManualManual Name How the Manuals for This Device Are OrganizedDescription About Warning Descriptions Safety PrecautionsWarnings Cautions Indicates that improper use can cause light or moderate injuryPrecautions for Use Notes on MaintenanceCleaning Eliminating Static Electricity from Twisted Pair Cables GroundingHigh safety SafetyHigh Safety Required Applications Electromagnetic Compatibility USANotes on Rack Mounting and Connecting a Powerstrip Laser SafetyAbout Fujitsus Green Products Notes on Use 1.1 Items in the Package, Descriptions and Functions 1.1.1 Parts List Chapter Getting Started1.1.2 Port Side 1.1.3 Power Inlet Side 1.1.4 Top Surface 1.2 Options 1.2.1 SFP Modules 1.2.2 SFP+ Modules 1.2.3 Compact Flash1.1 Items in the Package, Descriptions and Functions 1.1.1 Parts ListPrecautions 1.1.2 Port SideLED Details LED Name LED Functions / BehaviorsState Status000000000000 1.1.3 Power Inlet SideWarning Label 1.1.4 Top SurfaceXG0224 Hardware Guide Chapter 1 Getting Started1.2.1 SFP Modules 1.2 Options1.2.2 SFP+ Modules 1.2.3 Compact Flash1.2.4 Expansion Card LED Display ContentSFP+ Expansion Card LED Display Content CX4 Expansion CardLED Name StateChapter Installation 2.1.1 Installation Requirements 2.1 Requirements for Installation EnvironmentTemperature and Humidity Requirements Power RequirementsCheck List Installation ConditionCheck Item Check Result2.1.2 Space Requirements Ensuring the Space for Installation Maintenance of the Switch2.2.1 Installation of the Switch 2.2 InstallationInstallation on 19” Rack Two ways below are possible for putting on rack mounting brackets Installation of SFP+ Extension Card / CX4 Extension Card 2.2.2 Installation of Extension CardRemoving SFP+ Extension Card / CX4 Extension Card 2.3.2 Cleaning SFP Module / SFP+ Module / Optical Connector 2.3 Connecting the EquipmentCleaning of SFP Module / SFP+ Module 2.3.1 Discharging Twisted Pair CableRemoval of Micro Dust Cleaning of Optical Connectoroptical cable Connecting Twisted Pair CableTwisted pair cable Connecting SFP Module Connecting SFP+ Module Connecting CX4 Cable 2.3.4 Installing Compact Flash CardDo NOT unplug during access. It may result in crashing setting data Necessary Hardware / Software 2.4 Connecting to a Setup PCConnect RS232C Cable Power will turn on Turn on the PowerLog on using the terminal software Prepare a Setup PCz Command 2.5 Time SettingSwitch to Configuration mode When setting time zone to be “-0500“z Command 2.6 Set up IP addressIndex Issued on XG0224 Hardware GuideIssued by TA41001-6348