Fixing without KB fixing plate | Furuno FAR-2167DS-D, FAR-2167DS-BB

Fixing without KB fixing plate

1.Drill four mounting holes of 5 mm diameter, referring to the outline drawing at the back of this manual.

2.Fix the control unit with four screws (M4) from the under side of the desktop. (M4 screws with a sufficient length for the thickness of the desktop should be provided locally.)

#70

136±1

180

# Minimum recommended service space	308±1	4-M4 (Fixing holes)
	308±1	(bottom)
	398

Mounting dimensions for control unit RCU-014

24 32

F1

F2

F3

F4

136±1

180

110±1	4-M4 (Fixing holes)
160	(REAR)
160

Mounting dimensions for control unit RCU-015/RCU-016

1-11

Image 19

Furuno FAR-2167DS-D, FAR-2167DS-BB Fixing without KB fixing plate, Mounting dimensions for control unit RCU-014

Contents

Installation manual 00014869014 Safety Instructions Use only the specified power cables Iii System Configuration Name Type Code No Qty Remarks Standard supply Name Type Code No Remarks Optional equipment This page is intentionally left blank Mounting Antenna UnitMounting considerations Siting Mounting precaution for S-band antenna unit Installation precaution for S-band antenna unit Assembling the antenna unit Assembling the antenna unit Attachment of lifting fixtures, collar and ropes How to hoist the antenna unit Fastening the antenna unit to the mounting platform Installation of reinforcement ribs Mounting the antenna unit Monitor Unit Mounting procedureFlush mounting Desktop mounting Contents of desktop mounting kit FP03-09820 Attaching hand grips Fixing with KB keyboard fixing plate Control Unit Mounting dimensions for control unit RCU-015/RCU-016 Mounting dimensions for control unit RCU-014Fixing without KB fixing plate Name Type Qty Contents of flush mount kit for RCU-014/015/016 Control unit RCU-014, inside view Connecting RCU-016 in series with RCU-014 Changing cable entrance on control unit RCU-015/RCU-016 Changing the cable entrance on control unit RCU-015/RCU-016 Processor Unit Mounting dimensions for processor unit Mounting dimensions for power supply unit Power Supply Unit Wiring Overview Wiring Fabricating signal cable RW-9600 Fabricating signal cable RW-9600 and HV cable TYPCY-1.5Antenna unit, front view Armor Gasket Signal cable Flat washer Flat washer Gland nut How to fabricate HV cable TYPCY-1.5 How to wire Wago connector How to fabricate power cable TYPCY-2.5 Fabricating the power cable TYPCY-2.5 Antenna unit, left-side view Passing flat washer, etc. onto HV cable Monitor unit MU-201CR, rear view Fabricating the power cable DPYC-2.5Fabricating power cable DPYC-2.5 Monitor Unit for FAR-2167DS Processor Unit Processor unit, rear view Connection of cablesCable XH10P-W-6P L=20/30M Location of connectors inside the processor unit Location of connectors Power cable TPYC-1.5 Signal cable RW-9600 Between antenna unit and processor unit Port Conventional remote display FAR-2167DS Connection of Sub-display Fabricating cable connected to terminal TB1, TB2, TB3 Power supply unit, inside viewTerminal TB1 cable DPYC-2.5 Armor Processor unit, inside view Changing AC Power SpecificationPower supply Fuse Jumper connector P108 Processor unit How to adjust the overvoltage detection circuit Power Fuse Jumper connector P8 Power supply unit How to adjust the overvoltage detection circuit Initializing Tuning Adjustments Heading alignment Heading Alignment Echo ADJ menu For Control Unit RCU-014For Control Unit RCU-015 Initialize menu How to access the Initialize Menu with Control Unit RCU-015 Examples of correct and incorrect sweep timings Adjusting Sweep Timing Suppressing Main Bang Echo menu setting Other Settings Blind Sector 1 and Blind Sector Scanner menuANT SW and ANT Stopped Radar no and Radar Posn Installation menuOn Time and TX Time LENGTH/WIDTH, Scanner Posn and SUB Scanner Posn OWN Ship Info menuGPS 1 ANT Posn and GPS 2 ANT Posn ARP W/O Gyro Not shown on IMO radar Arpa Preset menuARP-related menus ANT Select EAV w/o Gyro Other menuOther menu This page intentionally left blank Gyro Converter GC-10 Installing the Gyro Converter board Fixing Gyro Converter board inside the processor unit Wiring Wago connector Connecting connector assemblies inside processor unit Attaching plastic cover for Gyro Converter board Connection of external power supply to Gyro Converter board Connection of external power supplyDIP switch, jumper wire settings Default setting JP1 JP1 JP2 JP3 JP4 JP5 Setting method 2 by make and model of gyrocompass Gyro Converter board 64P1106 HDG menu Setting the heading readout on the radar display Memory Card Interface Unit Flush mounting dimensions for memory card interface unit One memory card if unit and multiple processor units ConnectionsDesktop mount One memory card if unit and one processor unit Type Code No Contents DVI-RGB Conversion Kit How to wire the DVI-RBG conversion board Processor unit bottom chassis Processor unit, side view Connecting wires to the housing DVI-RGB BNC Connector Converter Input Data Specifications Contents RemarksOutput Sentence IEC 61162 input sentence and priorityIEC 61162 output sentence Sentence and order of priority ＰａｃｋｉｎｇＬｉｓｔ 1 SN30AF/SN36AF 70+6 000-157-497-10 工事材料表 000-155-826-10 PSU-006 AC100V 付属品表 03GL-X-9506 . CU-200-FAR GC-10-2 GC-10 $40# Page Page May 1707 R.Esumi Sep/2010 Y.NISHIYAMA Page Jan.1808 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Apr.2307 R.Esumi Page Page Page Page Page Page Page Page Page Interconnection Diagram