Manuals / Furuno / Communications / Telephone

Furuno FM-8800D manual CH no Info, Coast ACK Routine

Models: FM-8800D

1 121

Download 121 pages 21.21 Kb

Page 51

Image 51

3.DSC OPERATION FOR NON-DISTRESS CASES

2)Sending automatic acknowledge (ACK BQ) with comply status "UNABLE."

1.When the automatic acknowledge feature is active (AUTO ACK), the comply status is "UNABLE" and a coast or ship call is received, the display shown below appears, indicating that the auto acknowledge call with UNABLE (ACK BQ) has been sent. The alarm sounds and the ALARM LED blinks two minutes.

Unable acknowledge transmitted.

ROUTINE

TCmd1 : UNABLE

TCmd2 : BUSY

CH : NO INFO

CANCEL ALARM

2.Press the CANCEL key to silence the alarm. The following display appears.

**Send Message **

COAST ACK

TO : 003456789

ROUTINE

TCmd1 : UNABLE

TCmd2 : BUSY

CH : NO INFO

PRESS ENT

3.Press the ENT key.

4.If you want to send a proposal, prepare a message and sent it following the procedures shown on in paragraph 3.1.1.

3-7

Page 51

Image 51

Furuno FM-8800D manual CH no Info, Coast ACK Routine

Contents

VHF Radiotelephone 00014993000 DSC NUMBER, Position Example messageKeep heater away from equipment Do not open the equipmentDo not disassemble or modify the equipment Do not operate the equipment with wet handsImportant Notices Table of Contents DSC Operation for NON-DISTRESS Cases System Setup Foreword Word to FM-8800D/FM-8800S OwnersVii Features Program numberViii FM-8800S System ConfigurationThis page is intentionally left blank SP-1 Memory CHAfsk OUT TLL SP-2Operational Overview Controls Keys and LCD IndicationFront panel Controls ACK ABCTest GHIFile HI/LOShift LOGIndications on the LCD 10WATCH CH70LAT 34 45 N 1045 UTC LON 135 45 E Auto DUP Auto Manual ACK GPS Error Audio alarmsSelecting channel modes Turning the power on and adjusting contrastVHF Basic Operation Selecting channel modes, channelsTransmitting Adjusting volume of loudspeakerAdjusting squelch Selecting output powerRemarks on voice communications Quick selection of CH16Dual watch ScanningStandby display DSC Operational OverviewLED warnings DSC operational overviewPreparing and transmitting DSC messages Distress alert transmission and output powerWhen keyboard input is prohibited Automatic acknowledge on/offPriority How to set priority of the remote stationNature Undesignated DSC Distress CommunicationDistress Alert Transmission from the Distress Key Call Type DistressPress ENT Cancel AlarmTime to GO 4M 12S Distress ACKDistress Alert Transmission with Nature of Distress NatureundesignatedDistress communication Undesignated Call Type DistressSimp TP Routine Distress Alert Transmission from Call KeyCall Type Coast Call To Coast AAADSC NUMBER, DATE, Time UTC Canceling a False Distress AlertProcedure when in area A1 Vessel able Transmitting Dist ACK over CH16 Transmitting Dist ACK signalAfter transmitting Dist ACK DistressPress ENT to ACK Simp TP Press Call to SendCoast ID Routine When you should relay a distress alertSending Distress Relay on Behalf of a Ship in Distress Sending distress relay to coast stationCoast ID Input Type AutoAuto Call Type Relay SEL Sending distress relay to all shipsID in Dist no Info Call Type Relay ALLReceiving Distress Relay Receiving distress relay all callCall Type Relay ALL Distress Relay ALL Receiving distress relay from coast stationPress ENT This page is intentionally left blank General procedure for transmitting a coast or ship call DSC Operation for NON-DISTRESS CasesCoast or Ship Call Sending a coast or ship call Select CH Receiving acknowledgement of coast or ship call Time to GO 3M30 SCH no Info No response! Try calling again? Receiving a coast or ship callAble acknowledge call received Unable acknowledge call receivedSending automatic acknowledge ACK BQ with comply status Able Coast ACKCoast ACK Routine Manually acknowledging individual call with Able Ship CallManually acknowledging a coast or ship call with Unable Ship ACK RoutineNo Reason Busy Equip Disbld Mode Unavail CH UnavailGroup Call Sending a group callSelect CH Press ENT Receiving a group callSending a Pstn call Pstn CallPstn call disconnection ship disconnects line Receiving a Pstn call Pstn call disconnection coast station disconnects lineSending an all ships call All Ships CallSelect CH Case of OFF Hook Receiving an all ships callPress ENT to Change CH Case of on HookGeographical Area Call Sending a geographical area callCall Type Area Call Select CH Receiving a geographical area call Position call requesting other ships position Position CallCancel Alarm Position call other ship requests your position Automatic replyManual reply Polling Call Sending a polling callPosition Call Response is received+*. *!#$% Polling ACK Routine Receiving a polling callPolling Call Call Type Neutral Craft Neutral Craft CallSending a neutral craft call Receiving a neutral craft callSending a medical transport call Medical Transport CallUrgency Receiving a medical transport callShip Call Log FileOpening a log file Ship ACKECC OK Ship Call AnswerDelete Received LOG Are YOU SURE? Yesno This page is intentionally left blank Old position alarm in manual position entry mode Basic SetupAlarm Setup AlarmDSTRS/URG Safety OFFTo set type of alarm to output SafetyAble Auto ACK SetupComply Status Able Unable Reason No Reason Position Call on Polling Call onTo set reason for unable To set position call responseTo set polling call response Rcvd Distress Transmitted Erasing LogsErase LOG Menu Rcvd OrdinaryMemory Channel Setup IntlUSA WX Canada INLND-WA Priv Erase Coast Call Message File EntryAuto ACK Erase LOG Memory Channel Message File Entry Message File 1/13Group ID AreaShip ID Select CH Knob. Press the ENTkey Manual Position SetupPrint OUT Volume System PositionPrint Out Setup Xmtd Call ManualRcvd Call Manual Daily Test Manual EXT ENT Volume SetupEarpiece Level Setup Earpiece volumeIntercom Setup Intercom volumeOff-hook loudspeaker System Setup Displaying Self IDDisplaying Group ID List Naming Intercom Position Print OUT Volume Test SystemDisplaying Program Version This page is intentionally left blank When the power cannot be turned on Maintenance & TroubleshootingMaintenance TroubleshootingCH70 RX PCB OK TX Power TX/RX PCBDaily Test CPU PCBParts Location Error MessageANT Error GPS ErrorDMC Interface IF-8820 Handset HS-2003Remote station RB-8800/RB-8810 Junction box IF-8810Appendix Menu TreeAP-1 Appendix AP-2DSC Marine VHF Channel ListsAP-3 PWRAP-4 AP-5 AP-6 Private Channels AP-7AP-8 157.500 AP-9AP-10 AP-11 AP-12 AP-13 Output sentence Digital Interface IEC 61162-1 EditionInput sentences Load requirements as listnerAP-15 GGA -Global positioningsystem GPS fixdataAP-16 GNS-GNSS fixed dataAP-17 RMC Recommemded minimum specific GPS/TRANSIT dataAP-18 TLL Target latitude and longitudeIN-1 IndexIN-2