Error Message, Parts Location, ANT Error | Furuno FM-8800D guide

6. MAINTENANCE & TROUBLESHOOTING

6.4Error Message

The table below shows all the error messages which may appear.

Error message	Meaning

PLL1 Unlock	PLL circuit on the TX/RX pcb 05P0774 has unlocked.

PLL2 Unlock	PLL circuit on the DUP RX pcb 05P0777 has unlocked (only
	FM-8800D).

ANT ERROR	The antenna is abnormal. In this condition, if the
	transmission continues more than five seconds, the output
	power is reduced to approximately 10W.

GPS ERROR	There is no L/L input from a positioning sensor for more than
	one minute.

System Error	The DSP (digital signal processor) is abnormally.

Printer PE	Printer is disconnected or paper runs out.

Note: If the CPU is abnormal, the beep sounds continuously until turning off the power.

6.5Parts Location

Transceiver unit FM-8800D/8800S

PWR pcb			TX/RX pcb
PWR pcb			TX/RX pcb
05P0776			05P0774
DUPLEXER

FM-8800DFM-8800S

Top cover removed

PANEL pcb 05P0772

DUP RX pcb 05P0777

CH70 RX pcb

05P0775 CPU pcb

05P0773

FM-8800S/D

Bottom cover removed

6-3

Image 99

Furuno manual Error Message, Parts Location, ANT Error, GPS Error, Transceiver unit FM-8800D/8800S

Contents

VHF Radiotelephone 00014993000 DSC NUMBER, Position Example message Safety Instructions Important Notices Table of Contents DSC Operation for NON-DISTRESS Cases System Setup Foreword Word to FM-8800D/FM-8800S OwnersVii Features Program numberViii FM-8800D System Configuration This page is intentionally left blank SP-1 Memory CHAfsk OUT TLL SP-2 Operational Overview Controls Keys and LCD IndicationFront panel Controls ACK ABCTest GHI File HI/LOShift LOG Indications on the LCD 116 DUP Auto Manual ACK GPS Error Audio alarms Selecting channel modes Turning the power on and adjusting contrastVHF Basic Operation Selecting channel modes, channels Transmitting Adjusting volume of loudspeakerAdjusting squelch Selecting output power Remarks on voice communications Quick selection of CH16Dual watch Scanning Standby display DSC Operational OverviewLED warnings DSC operational overview Preparing and transmitting DSC messages Distress alert transmission and output powerWhen keyboard input is prohibited Automatic acknowledge on/off Priority How to set priority of the remote station Nature Undesignated DSC Distress CommunicationDistress Alert Transmission from the Distress Key Call Type Distress Press ENT Cancel AlarmTime to GO 4M 12S Distress ACK Distress Alert Transmission with Nature of Distress NatureundesignatedDistress communication Undesignated Call Type DistressSimp TP Routine Distress Alert Transmission from Call KeyCall Type Coast Call To Coast AAA DSC NUMBER, DATE, Time UTC Canceling a False Distress Alert Procedure when in area A1 Vessel able Transmitting Dist ACK over CH16 Transmitting Dist ACK signal After transmitting Dist ACK DistressPress ENT to ACK Simp TP Press Call to Send Coast ID Routine When you should relay a distress alertSending Distress Relay on Behalf of a Ship in Distress Sending distress relay to coast station Coast ID Input Type AutoAuto Call Type Relay SEL Sending distress relay to all ships ID in Dist no Info Call Type Relay ALL Receiving Distress Relay Receiving distress relay all callCall Type Relay ALL Distress Relay ALL Receiving distress relay from coast station Press ENT This page is intentionally left blank General procedure for transmitting a coast or ship call DSC Operation for NON-DISTRESS CasesCoast or Ship Call Sending a coast or ship call Select CH Receiving acknowledgement of coast or ship call Time to GO 3M30 SCH no Info No response! Try calling again? Receiving a coast or ship callAble acknowledge call received Unable acknowledge call received Sending automatic acknowledge ACK BQ with comply status Able Coast ACK Coast ACK Routine Manually acknowledging individual call with Able Ship Call Manually acknowledging a coast or ship call with Unable Ship ACK Routine No Reason Busy Equip Disbld Mode Unavail CH UnavailGroup Call Sending a group call Press the ENTkeytoopen the calltypelist Press ENT Receiving a group call Sending a Pstn call Pstn Call Pstn call disconnection ship disconnects line Receiving a Pstn call Pstn call disconnection coast station disconnects line Sending an all ships call All Ships Call Select CH Case of OFF Hook Receiving an all ships callPress ENT to Change CH Case of on Hook Geographical Area Call Sending a geographical area callCall Type Area Call Select CH Receiving a geographical area call Position call requesting other ships position Position Call Cancel Alarm Position call other ship requests your position Automatic replyManual reply Polling Call Sending a polling callPosition Call Response is received+*. *!#$% Polling ACK Routine Receiving a polling call Polling Call Call Type Neutral Craft Neutral Craft CallSending a neutral craft call Receiving a neutral craft call Sending a medical transport call Medical Transport Call Urgency Receiving a medical transport call Ship Call Log FileOpening a log file Ship ACK ECC OK Ship Call AnswerDelete Received LOG Are YOU SURE? Yesno This page is intentionally left blank Old position alarm in manual position entry mode Basic SetupAlarm Setup Alarm DSTRS/URG Safety OFFTo set type of alarm to output Safety Able Auto ACK SetupComply Status Able Unable Reason No Reason Position Call on Polling Call on To set reason for unable To set position call responseTo set polling call response Rcvd Distress Transmitted Erasing LogsErase LOG Menu Rcvd Ordinary Memory Channel Setup IntlUSA WX Canada INLND-WA Priv Erase Coast Call Message File EntryAuto ACK Erase LOG Memory Channel Message File Entry Message File 1/13 Group ID AreaShip ID Select CH #$#!% Manual Position SetupPrint OUT Volume System Position Print Out Setup Xmtd Call ManualRcvd Call Manual Daily Test Manual EXT ENT Volume SetupEarpiece Level Setup Earpiece volume Intercom Setup Intercom volumeOff-hook loudspeaker System Setup Displaying Self IDDisplaying Group ID List Naming Intercom Position Print OUT Volume Test System Displaying Program Version This page is intentionally left blank When the power cannot be turned on Maintenance & TroubleshootingMaintenance Troubleshooting CH70 RX PCB OK TX Power TX/RX PCBDaily Test CPU PCB Parts Location Error MessageANT Error GPS Error DMC Interface IF-8820 Handset HS-2003Remote station RB-8800/RB-8810 Junction box IF-8810 Appendix Menu TreeAP-1 Appendix AP-2 DSC Marine VHF Channel ListsAP-3 PWR AP-4 AP-5 AP-6 Private Channels AP-7 AP-8 157.500 AP-9 AP-10 AP-11 AP-12 AP-13 Output sentence Digital Interface IEC 61162-1 EditionInput sentences Load requirements as listner GGA -Global positioningsystem GPS fixdata AP-15 AP-16 GNS-GNSS fixed data AP-17 RMC Recommemded minimum specific GPS/TRANSIT data AP-18 TLL Target latitude and longitude IN-1 Index IN-2