Manuals / Furuno / Communications / Telephone

Furuno FM-8800D manual Receiving a polling call, Polling ACK Routine

Models: FM-8800D

1 121

Download 121 pages 21.21 Kb

Page 71

Image 71

3. DSC OPERATION FOR NON-DISTRESS CASES

9-2. When "No response! Try calling again?" is displayed, do one of the following:

Re-send call: Push the ENT key followed by the CALL key.

Cancel call: Press the CANCEL key to return to the standby display.

3.7.2Receiving a polling call

Automatic reply

1.When a polling request is received and the equipment is set up for automatic acknowledge POLLING on the AUTO ACK menu is ON and the ACK key is set to show AUTO ACK on the display, the display changes as shown in the illustration below and the audio alarm sounds.

Polling auto ack transmitted.

ROUTINE

TCmd1 : POLLING

TCmd2 : NO INFO

CANCEL ALARM

2.Press the CANCEL or ENT key to silence the alarm. The display changes as below.

**Send Message **

POLLING ACK

TO : 123456789

ROUTINE

TCmd1 : POLLING

TCmd2 : NO INFO

PRESS ENT

3-27

Page 71

Image 71

Furuno FM-8800D manual Receiving a polling call, Polling ACK Routine

Contents

VHF Radiotelephone 00014993000 DSC NUMBER, Position Example messageKeep heater away from equipment Do not open the equipmentDo not disassemble or modify the equipment Do not operate the equipment with wet handsImportant Notices Table of Contents DSC Operation for NON-DISTRESS Cases System Setup Vii ForewordWord to FM-8800D/FM-8800S Owners Viii FeaturesProgram number FM-8800S System ConfigurationThis page is intentionally left blank Afsk SP-1Memory CH OUT TLL SP-2Front panel Operational OverviewControls Keys and LCD Indication Controls ACK ABCTest GHIFile HI/LOShift LOGLAT 34 45 N 1045 UTC LON 135 45 E Auto Indications on the LCD10WATCH CH70 DUP Auto Manual ACK GPS Error Audio alarmsSelecting channel modes Turning the power on and adjusting contrastVHF Basic Operation Selecting channel modes, channelsTransmitting Adjusting volume of loudspeakerAdjusting squelch Selecting output powerRemarks on voice communications Quick selection of CH16Dual watch ScanningStandby display DSC Operational OverviewLED warnings DSC operational overviewPreparing and transmitting DSC messages Distress alert transmission and output powerWhen keyboard input is prohibited Automatic acknowledge on/offPriority How to set priority of the remote stationNature Undesignated DSC Distress CommunicationDistress Alert Transmission from the Distress Key Call Type DistressPress ENT Cancel AlarmTime to GO 4M 12S Distress ACKDistress communication Distress Alert Transmission with Nature of DistressNatureundesignated Simp TP UndesignatedCall Type Distress Routine Distress Alert Transmission from Call KeyCall Type Coast Call To Coast AAADSC NUMBER, DATE, Time UTC Canceling a False Distress AlertProcedure when in area A1 Vessel able Transmitting Dist ACK over CH16 Transmitting Dist ACK signalAfter transmitting Dist ACK DistressPress ENT to ACK Simp TP Press Call to SendCoast ID Routine When you should relay a distress alertSending Distress Relay on Behalf of a Ship in Distress Sending distress relay to coast stationAuto Coast IDInput Type Auto Call Type Relay SEL Sending distress relay to all shipsID in Dist no Info Call Type Relay ALLCall Type Relay ALL Receiving Distress RelayReceiving distress relay all call Distress Relay ALL Receiving distress relay from coast stationPress ENT This page is intentionally left blank Coast or Ship Call General procedure for transmitting a coast or ship callDSC Operation for NON-DISTRESS Cases Sending a coast or ship call Select CH CH no Info Receiving acknowledgement of coast or ship callTime to GO 3M30 S No response! Try calling again? Receiving a coast or ship callAble acknowledge call received Unable acknowledge call receivedSending automatic acknowledge ACK BQ with comply status Able Coast ACKCoast ACK Routine Manually acknowledging individual call with Able Ship CallManually acknowledging a coast or ship call with Unable Ship ACK RoutineNo Reason Busy Equip Disbld Mode Unavail CH UnavailGroup Call Sending a group callSelect CH Press ENT Receiving a group callSending a Pstn call Pstn CallPstn call disconnection ship disconnects line Receiving a Pstn call Pstn call disconnection coast station disconnects lineSending an all ships call All Ships CallSelect CH Case of OFF Hook Receiving an all ships callPress ENT to Change CH Case of on HookCall Type Area Call Geographical Area CallSending a geographical area call Select CH Receiving a geographical area call Position call requesting other ships position Position CallCancel Alarm Manual reply Position call other ship requests your positionAutomatic reply Position Call Polling CallSending a polling call Response is received+*. *!#$% Polling ACK Routine Receiving a polling callPolling Call Call Type Neutral Craft Neutral Craft CallSending a neutral craft call Receiving a neutral craft callSending a medical transport call Medical Transport CallUrgency Receiving a medical transport callShip Call Log FileOpening a log file Ship ACKDelete Received LOG Are YOU SURE? Yesno ECC OK Ship CallAnswer This page is intentionally left blank Old position alarm in manual position entry mode Basic SetupAlarm Setup AlarmDSTRS/URG Safety OFFTo set type of alarm to output SafetyAble Auto ACK SetupComply Status Able Unable Reason No Reason Position Call on Polling Call onTo set polling call response To set reason for unableTo set position call response Rcvd Distress Transmitted Erasing LogsErase LOG Menu Rcvd OrdinaryUSA WX Canada INLND-WA Priv Erase Memory Channel SetupIntl Coast Call Message File EntryAuto ACK Erase LOG Memory Channel Message File Entry Message File 1/13Ship ID Group IDArea Select CH Knob. Press the ENTkey Manual Position SetupPrint OUT Volume System PositionRcvd Call Manual Daily Test Manual Print Out SetupXmtd Call Manual EXT ENT Volume SetupEarpiece Level Setup Earpiece volumeOff-hook loudspeaker Intercom SetupIntercom volume Displaying Group ID List System SetupDisplaying Self ID Naming Intercom Position Print OUT Volume Test SystemDisplaying Program Version This page is intentionally left blank When the power cannot be turned on Maintenance & TroubleshootingMaintenance TroubleshootingCH70 RX PCB OK TX Power TX/RX PCBDaily Test CPU PCBParts Location Error MessageANT Error GPS ErrorDMC Interface IF-8820 Handset HS-2003Remote station RB-8800/RB-8810 Junction box IF-8810AP-1 AppendixMenu Tree Appendix AP-2DSC Marine VHF Channel ListsAP-3 PWRAP-4 AP-5 AP-6 Private Channels AP-7AP-8 157.500 AP-9AP-10 AP-11 AP-12 AP-13 Output sentence Digital Interface IEC 61162-1 EditionInput sentences Load requirements as listnerAP-15 GGA -Global positioningsystem GPS fixdataAP-16 GNS-GNSS fixed dataAP-17 RMC Recommemded minimum specific GPS/TRANSIT dataAP-18 TLL Target latitude and longitudeIN-1 IndexIN-2