Manuals / Furuno / Communications / Telephone

Furuno FM-8800D manual Pstn call disconnection ship disconnects line, Press ENT

Models: FM-8800D

1 121

Download 121 pages 21.21 Kb

Page 58

3. DSC OPERATION FOR NON-DISTRESS CASES

If a response from the coast station is received within five seconds, transmit PSTN CALL (EOS) signal and then carrier frequency during two seconds. Then your phone rings. Press the CANCEL key to stop the calling sound and change to standby display. Hook off and communicate with other party.

Note: If using a hand-microphone, pressing the CANCEL key is equal to off-hook.

3.3.2PSTN call disconnection (ship disconnects line)

1.After hanging up the handset or pressing the CANCEL key to complete your call, the display shows the following message. The end of call signal is transmitted; and the system then waits for a response from the coast station.

Waiting for acknowledgement

FROM : 003456789

TCmd1 : DUPLEX TP

TCmd2 : PAY-PHONE

TEL : 1234567890123456

CH : 28

2.When the ACK from the coast station is received, the following display appears. The communication time (charge time) is informed.

Able acknowledge call received.

FROM : 003456789

TCmd1 : END CALL

TCmd2 : NO INFO

TEL : 1234567890123456

CHARGE TIME : 00h05m18s

PRESS ENT

3-14

Image 58

Furuno FM-8800D manual Pstn call disconnection ship disconnects line, Press ENT

Contents

VHF Radiotelephone 00014993000 Example message DSC NUMBER, PositionSafety Instructions Important Notices Table of Contents DSC Operation for NON-DISTRESS Cases System Setup Word to FM-8800D/FM-8800S Owners ForewordVii Program number FeaturesViii System Configuration FM-8800DThis page is intentionally left blank Memory CH SP-1Afsk SP-2 OUT TLLControls Keys and LCD Indication Operational OverviewFront panel Controls GHI ABCTest ACKLOG HI/LOShift File116 Indications on the LCDAudio alarms DUP Auto Manual ACK GPS ErrorSelecting channel modes, channels Turning the power on and adjusting contrastVHF Basic Operation Selecting channel modesSelecting output power Adjusting volume of loudspeakerAdjusting squelch TransmittingScanning Quick selection of CH16Dual watch Remarks on voice communicationsDSC operational overview DSC Operational OverviewLED warnings Standby displayAutomatic acknowledge on/off Distress alert transmission and output powerWhen keyboard input is prohibited Preparing and transmitting DSC messagesHow to set priority of the remote station PriorityCall Type Distress DSC Distress CommunicationDistress Alert Transmission from the Distress Key Nature UndesignatedDistress ACK Cancel AlarmTime to GO 4M 12S Press ENTNatureundesignated Distress Alert Transmission with Nature of DistressDistress communication Call Type Distress UndesignatedSimp TP To Coast AAA Distress Alert Transmission from Call KeyCall Type Coast Call RoutineCanceling a False Distress Alert DSC NUMBER, DATE, Time UTCProcedure when in area A1 Vessel able Transmitting Dist ACK signal Transmitting Dist ACK over CH16Simp TP Press Call to Send DistressPress ENT to ACK After transmitting Dist ACKSending distress relay to coast station When you should relay a distress alertSending Distress Relay on Behalf of a Ship in Distress Coast ID RoutineInput Type Auto Coast IDAuto Sending distress relay to all ships Call Type Relay SELCall Type Relay ALL ID in Dist no InfoReceiving distress relay all call Receiving Distress RelayCall Type Relay ALL Receiving distress relay from coast station Distress Relay ALLPress ENT This page is intentionally left blank DSC Operation for NON-DISTRESS Cases General procedure for transmitting a coast or ship callCoast or Ship Call Sending a coast or ship call Select CH Time to GO 3M30 S Receiving acknowledgement of coast or ship callCH no Info Unable acknowledge call received Receiving a coast or ship callAble acknowledge call received No response! Try calling again?Coast ACK Sending automatic acknowledge ACK BQ with comply status AbleCoast ACK Routine Ship Call Manually acknowledging individual call with AbleShip ACK Routine Manually acknowledging a coast or ship call with UnableSending a group call Busy Equip Disbld Mode Unavail CH UnavailGroup Call No ReasonPress the ENTkeytoopen the calltypelist Receiving a group call Press ENTPstn Call Sending a Pstn callPstn call disconnection ship disconnects line Pstn call disconnection coast station disconnects line Receiving a Pstn callAll Ships Call Sending an all ships callSelect CH Case of on Hook Receiving an all ships callPress ENT to Change CH Case of OFF HookSending a geographical area call Geographical Area CallCall Type Area Call Select CH Receiving a geographical area call Position Call Position call requesting other ships positionCancel Alarm Automatic reply Position call other ship requests your positionManual reply Sending a polling call Polling CallPosition Call Response is received+*. *!#$% Receiving a polling call Polling ACK RoutinePolling Call Receiving a neutral craft call Neutral Craft CallSending a neutral craft call Call Type Neutral CraftMedical Transport Call Sending a medical transport callReceiving a medical transport call UrgencyShip ACK Log FileOpening a log file Ship CallAnswer ECC OK Ship CallDelete Received LOG Are YOU SURE? Yesno This page is intentionally left blank Alarm Basic SetupAlarm Setup Old position alarm in manual position entry modeSafety Safety OFFTo set type of alarm to output DSTRS/URGUnable Reason No Reason Position Call on Polling Call on Auto ACK SetupComply Status Able AbleTo set position call response To set reason for unableTo set polling call response Rcvd Ordinary Erasing LogsErase LOG Menu Rcvd Distress TransmittedIntl Memory Channel SetupUSA WX Canada INLND-WA Priv Erase Message File 1/13 Message File EntryAuto ACK Erase LOG Memory Channel Message File Entry Coast CallArea Group IDShip ID Select CH #$#!% Position Position SetupPrint OUT Volume System ManualXmtd Call Manual Print Out SetupRcvd Call Manual Daily Test Manual Earpiece volume Volume SetupEarpiece Level Setup EXT ENTIntercom volume Intercom SetupOff-hook loudspeaker Displaying Self ID System SetupDisplaying Group ID List Position Print OUT Volume Test System Naming IntercomDisplaying Program Version This page is intentionally left blank Troubleshooting Maintenance & TroubleshootingMaintenance When the power cannot be turned onCPU PCB TX Power TX/RX PCBDaily Test CH70 RX PCB OKGPS Error Error MessageANT Error Parts LocationJunction box IF-8810 Handset HS-2003Remote station RB-8800/RB-8810 DMC Interface IF-8820Menu Tree AppendixAP-1 AP-2 AppendixPWR Marine VHF Channel ListsAP-3 DSCAP-4 AP-5 AP-6 AP-7 Private ChannelsAP-8 AP-9 157.500AP-10 AP-11 AP-12 AP-13 Load requirements as listner Digital Interface IEC 61162-1 EditionInput sentences Output sentenceAP-15 GGA -Global positioningsystem GPS fixdataGNS-GNSS fixed data AP-16RMC Recommemded minimum specific GPS/TRANSIT data AP-17TLL Target latitude and longitude AP-18Index IN-1IN-2