J10 20P8171 | Furuno SC-60 specs

2.INSTALLATION

9.Fix the PH connector assy. with a clamp as shown below.

Pass PH connector through clamp

J2

DGPS Receiver

Assy.

J7

J8 (BLK)

9 (RED)

J1

J10

20P8171

J6

J5 (BLK)

J4 (RED)

J3

20P8164

J1

J4

Processor unit, cover removed, top view

10.Close the top cover of the processor unit.

11.Mount the DGPS antenna and whip antenna, referring to section 2.2.2.

2-24

Image 38

Furuno SC-60 manual J10 20P8171

Contents

Satellite Compass 00080919106 Safety Instructions Table of Contents Appendix B Installation of Antenna Unit SC-603 Iii Word to the Owner of the SC-60 FeaturesForeword System Configuration System configuration Dgps Equipment ListName Type Code No Qty Remarks Software Version List Vii This page is intentionally left blank Interface SC-60General Coating Color Power SupplyEnvironmental Condition and EMC Principle of Operation Principle of satellite compass operation This page is intentionally left blank SC-series antenna unit InstallationMounting Considerations Horizontal separation between antenna and masts InstallationMast diameter Separation distance minimum Antenna and field of view Example of antenna installed below superstructures Display unit, processor unit Installing the Antenna Units Mounting dimensions for antenna, orienting the antenna Coating bolt, nut and washers with silicone sealant Waterproofing the antenna connectorHow to fasten the antenna cable Cable from antenna No. marked on cable How to insert the cable cover Antenna unit Dgps antenna unit Mounting the Dgps antenna Antenna cable set Type OP08-17, Code No Waterproofing the extension connectorCable connection when using cable RG-10UY Processor unit orientation, deck mounting Installing the Processor UnitDeck mount Angular rate sensor, top view Bulkhead mountProcessor unit, top view HEAD1HEAD2HEAD3 Processor unit orientation, bulkhead mounting Installation on the underside of a deskInstallation of processor unit on the underside of a desk Processor Unit, rear view Direction a Direction B Desktop, overhead mounting Installing the Display UnitAdjusting for orientation error Display unit mounting methods Name Type Flush mountFlush mount F Flush mount S Antenna TPPX6-3D2V-15M Port on WiringGeneral wiring diagram GPS ANT How to install the optional antenna cable set How to attach connector N-P-8DFB How to attach connector N-P-8DFB Confirming satellite status choosing mounting method Initial SettingsInstallation setup menu Main menu Heading setup menu Choosing heading source Heading data format Jumper wire and format on the circuit board 20P8171Port Format Setting Remarks Processor unit, cover opened, top view TNCBPJ140 Installing the Dgps Beacon Receiver KitConnection of External Equipment Procedure Processor unit, cover removed, top view J10 20P8171 Display unit OperationControls Processor unit Turning the Power On/OffPanel Illumination, Display Contrast Heading display Choosing a DisplayDescription of displays Nav data display ROT Rate-of-Turn display Steering displayCompass display Set and Drift display, Distance Run display Alarm menu, GPS buzzer options AlarmsAlarm menu Satellite status display Alarm menu, Dgps buzzer optionsConfirming Satellite Status GPS Setup menu description GPS SetupDisplaying the GPS setup menu Output Data Heading NAV OUT menu Navigation dataInterface OFF Log pulse rate selection window Log pulseTalker identifier mnemonics Heading talker selection window Geodetic data System SetupSystem Setup menu Time format Using local timeUnits of measurement Manual Dgps setup Dgps SetupDemonstration mode Dgps menu INT Beacon receiver selection window Beacon station display Programming user beacon stationsStation Nearest Station User Display for editing user channels Editing user beacon stationsNEW User Channel display Prompt for erasure of all user channels Erasing individual user stationsErasing all user beacon stations Others Menu Others menu Trip Menu Resetting Distance RunReset Distance prompt Trip menu This page is intentionally left blank Do not open the equipment MAINTENANCE, TroubleshootingPreventive Maintenance Symptom Cause Remedy TroubleshootingDiagnostics Diagnostic test1 LCD Check MAINTENANCE, TroubleshootingDiagnostic test sequence Diagnostic test2 TEST2 display Program version no. display Program NumberClearing Data Prompts for erasure of data Battery exchange options Replacement of BatteryBattery Location Type Code No Prompt for exchanging battery Error Message Meaning Remedy Replacement of FuseError Messages Message display Error messages con’t from previous Appendix a Menu Tree Geodetic Chart Codes North American Digital Interface Schematic diagrams NAV OUT1 Port Data sentences PFECatt- True heading, pitching, rolling HDM- Heading magnetic VDR Set and drift Appendix a VTG Course over ground and ground speed Port Label Connector Signal Remarks Type Input/Output Ports Parts Location Processor unit, cover removed Parts List R U N O Appendix B Installing the Antenna UnitHow to orient the antenna elements Antenna unit SC-603 Appendix B Fixing antenna unit to pedestal Orient the antenna unit as shown in the illustration below Orienting the antenna unit Welding the Antenna Unit Fastening the antenna cable Antenna element This page is intentionally left blank ＰａｃｋｉｎｇＬｉｓｔ SC-303 工事材料表 Installation Materials Page Installation Materials Page Page Page GP-1850,GP-1650,FA-100,GP-1640/F SC-60/120,GD/GP-280/680/380 20AG-X-9405 Page Page Page Page Page Page Page Page Page Index Index-1