Bulkhead mount, Processor unit, top view | Furuno SC-60 guide

2. INSTALLATION

2.3.2Bulkhead mount

For mounting on a bulkhead, use the bulkhead mounting plate supplied with the installation materials.

1.Unfasten four screws from the top cover to open the front panel.

2.Unfasten two screws to dismount the angular rate sensor.

Angular Rate Sensor

BEACON

20P8171

Processor unit, top view

3.Fasten the bulkhead mounting plate to the angular rate sensor. Align the center graduation on the sensor with the hole of the bulkhead mounting plate and tighten fixing screws.

	Hole of bulkhead
Scale	mounting plate
Scale
Center Mark

Angular Rate Sensor

Mounting Base

Fixing Screw

Angular rate sensor, top view

2-10

Image 24

Furuno SC-60 manual Bulkhead mount, Processor unit, top view, Angular rate sensor, top view

Contents

Satellite Compass 00080919106 Safety Instructions Table of Contents Appendix B Installation of Antenna Unit SC-603 Iii Features ForewordWord to the Owner of the SC-60 System Configuration System configuration Equipment List Name Type Code No Qty RemarksDgps Software Version List Vii This page is intentionally left blank SC-60 GeneralInterface Power Supply Environmental Condition and EMCCoating Color Principle of Operation Principle of satellite compass operation This page is intentionally left blank Installation Mounting ConsiderationsSC-series antenna unit Installation Mast diameter Separation distance minimumHorizontal separation between antenna and masts Antenna and field of view Example of antenna installed below superstructures Display unit, processor unit Installing the Antenna Units Mounting dimensions for antenna, orienting the antenna Waterproofing the antenna connector How to fasten the antenna cableCoating bolt, nut and washers with silicone sealant Cable from antenna No. marked on cable How to insert the cable cover Antenna unit Dgps antenna unit Mounting the Dgps antenna Waterproofing the extension connector Cable connection when using cable RG-10UYAntenna cable set Type OP08-17, Code No Installing the Processor Unit Deck mountProcessor unit orientation, deck mounting Bulkhead mount Processor unit, top viewAngular rate sensor, top view HEAD1HEAD2HEAD3 Installation on the underside of a desk Installation of processor unit on the underside of a deskProcessor unit orientation, bulkhead mounting Processor Unit, rear view Direction a Direction B Installing the Display Unit Adjusting for orientation errorDesktop, overhead mounting Display unit mounting methods Flush mount Flush mount FName Type Flush mount S Wiring General wiring diagramAntenna TPPX6-3D2V-15M Port on GPS ANT How to install the optional antenna cable set How to attach connector N-P-8DFB How to attach connector N-P-8DFB Initial Settings Installation setup menuConfirming satellite status choosing mounting method Main menu Heading setup menu Choosing heading source Jumper wire and format on the circuit board 20P8171 Port Format Setting RemarksHeading data format Processor unit, cover opened, top view Installing the Dgps Beacon Receiver Kit Connection of External EquipmentTNCBPJ140 Procedure Processor unit, cover removed, top view J10 20P8171 Operation ControlsDisplay unit Turning the Power On/Off Panel Illumination, Display ContrastProcessor unit Choosing a Display Description of displaysHeading display Nav data display Steering display Compass displayROT Rate-of-Turn display Set and Drift display, Distance Run display Alarms Alarm menuAlarm menu, GPS buzzer options Alarm menu, Dgps buzzer options Confirming Satellite StatusSatellite status display GPS Setup Displaying the GPS setup menuGPS Setup menu description Output Data Heading Navigation data InterfaceNAV OUT menu OFF Log pulse Talker identifier mnemonicsLog pulse rate selection window Heading talker selection window System Setup System Setup menuGeodetic data Using local time Units of measurementTime format Dgps Setup Demonstration modeManual Dgps setup Dgps menu INT Beacon receiver selection window Programming user beacon stations Station NearestBeacon station display Station User Editing user beacon stations NEW User Channel displayDisplay for editing user channels Erasing individual user stations Erasing all user beacon stationsPrompt for erasure of all user channels Others Menu Others menu Resetting Distance Run Reset Distance promptTrip Menu Trip menu This page is intentionally left blank MAINTENANCE, Troubleshooting Preventive MaintenanceDo not open the equipment Troubleshooting DiagnosticsSymptom Cause Remedy Diagnostic test1 MAINTENANCE, Troubleshooting Diagnostic test sequenceLCD Check Diagnostic test2 TEST2 display Program Number Clearing DataProgram version no. display Prompts for erasure of data Replacement of Battery Battery Location Type Code NoBattery exchange options Prompt for exchanging battery Replacement of Fuse Error MessagesError Message Meaning Remedy Message display Error messages con’t from previous Appendix a Menu Tree Geodetic Chart Codes North American Digital Interface Schematic diagrams NAV OUT1 Port Data sentences PFECatt- True heading, pitching, rolling HDM- Heading magnetic VDR Set and drift Appendix a VTG Course over ground and ground speed Port Label Connector Signal Remarks Type Input/Output Ports Parts Location Processor unit, cover removed Parts List R U N O Installing the Antenna Unit How to orient the antenna elementsAppendix B Antenna unit SC-603 Appendix B Fixing antenna unit to pedestal Orient the antenna unit as shown in the illustration below Orienting the antenna unit Welding the Antenna Unit Fastening the antenna cable Antenna element This page is intentionally left blank ＰａｃｋｉｎｇＬｉｓｔ SC-303 工事材料表 Installation Materials Page Installation Materials Page Page Page GP-1850,GP-1650,FA-100,GP-1640/F SC-60/120,GD/GP-280/680/380 20AG-X-9405 Page Page Page Page Page Page Page Page Page Index Index-1