2.3Internal Connections, basic AUI Port and Port Modules

Magnum 1000 Workgroup Hubs

Installation and User Guide (04/02)

2.3Internal Connections, basic AUI Port and Port Modules

Figure 2.3a shows the internal layout of the Magnum 1008 for each of the two

rear port configuration options (see section 2.2.1). Unless otherwise specified at the time of order, the Magnum 1008 is shipped with a basic AUI port. For greater application flexibility, any of the Magnum PMs may be specified at the time of order for factory configuration. It is also possible for the rear port to be re-configured in the field by a trained technician to exchange or add Port Modules.

NOTE: When changing from the basic AUI port to a Port Module option in the field, it is necessary to have a Port Module connector cable (part number CBL-PM available as a spare part from GCI) in addition to the desired PM.

Basic AUI port

 

 

 

 

 

 

 

 

 

 

Optional PM card

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(BPM shown)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

P1-RPM

P1

P1-RPM

P1

NOTE:

Use P1 for Basic AUI port Use P1-RPM for PM

PM Ribbon cable with 16 pin headers.

(Included only when PM is factory installed. May be ordered separately as part # CBL-PM)

Figure 2.3a: Model 1008 Internal Connections, Basic AUI port and Port Module

Figure 2.3b shows the internal layout of the Magnum 1016 and 1024

Workgroup Hubs. (The Model 1024 is shown in the figure, but all rear port connections are identical for the Model 1016). One rear port always has the basic AUI port in it. The bonus port slot, in the center of the chassis rear, is available for configuring any PM. For application flexibility, any of the Magnum PMs may be specified on an order for factory configuration in the bonus port slot. It is also possible for the bonus port to be re-configured in the field by a trained technician to exchange or add Port Modules.

NOTE: When adding a Port Module option to the Bonus Port slot in the field, it is necessary to have a Port Module connector cable (part # CBL-PM available as a spare part from GCI) in addition to the desired PM. See also Section 2.4.12, Special Option.

www . GarrettCom . com

8

Page 14
Image 14
GarrettCom 1008, 1016, 1024 manual Basic AUI port, Optional PM card, BPM shown, PM Ribbon cable with 16 pin headers