Magnum 1008, 1016 and, Magnum 1000 Workgroup Hubs | GarrettCom

Magnum 1000 Workgroup Hubs

Installation and User Guide (04/02)

Magnum 1008, 1016 and 1024

and optional 48VDC, 24VDC &125VDC-powered models

Workgroup Hubs

Installation and User Guide

Part #: 84-00030 Rev 04/02

Trademarks

Ethernet is a trademark of Xerox Corporation

NEBS is a trademark of Telcordia Technologies

UL is a registered trademark of Underwriters Laboratories

GarrettCom, Magnum and Personal Switch are trademarks and Personal Hub is a registered trademark of GarrettCom, Inc.

Important: The Magnum 1000 series workgroup hub family contains no user serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void. If problems are experienced with Magnum 1000 series workgroup hub products, consult Section 5, Troubleshooting, of this User Guide.

Copyright  2002 GarrettCom, Inc. All rights reserved. No part

of this publication may be reproduced without prior written permission from

GarrettCom, Inc.

Printed in the United States of America.

www . GarrettCom . com

i

Image 2

GarrettCom Magnum 1008, 1016 and, Workgroup Hubs Installation and User Guide, Magnum 1000 Workgroup Hubs, Trademarks

Contents

Magnum Workgroup Hubs “Ten Series” Models 1008, 1016 andInstallation and User Guide www . GarrettCom . com and optional 48VDC, 24VDC &125VDC-powered models Workgroup Hubs Installation and User GuideMagnum 1008, 1016 and Installation and User Guide 04/02 Phone 510 GarrettCom, Inc47823 Westinghouse Drive Fremont, CA Fax 510 Page APPENDIX B OPTIONAL 48V POWER SUPPLY, ADDENDUMTABLE OF CONTENTS Revisions Stackable Hubs, SNMP Optional Personal Switches, 10/100MbThe Magnum Line Personal Hubs, 10Mb series Switches 1.0 SPECIFICATIONS 1.1 Technical Specifications PerformanceConnectors Network Standards Warranty Power Supply InternalFor 48VDC power input option, see Appendix B Agency Approvals 1.2 Specifications - Repeater Port Modules RPMs 1.4 Ordering Information Magnum 1000 Workgroup HubsMagnum Magnum Magnum 2.0 INTRODUCTION 2.1 Inspecting the Package and Product 2.2 Product Description - Magnum 1000-series Workgroup Hubs 2.2.1 Magnum 1008 Workgroup Hub Figure 2.2.1a Front view - Magnum 1008 Workgroup Hub Magnum 1000 Workgroup Hubs Installation and User Guide 04/02AC Power 115 - 230 VAC RPM-FST Shown Configurable Bonus PortFigure 2.2.2b Front view - Magnum 1024 Workgroup Hub Figure 2.2.2c Rear view - Magnum 1016 and 1024 Workgroup Hubs BPM shown Basic AUI portOptional PM card PM Ribbon cable with 16 pin headers Bonus port for optional Basic AUI port PM card BPM shown Magnum 1000 Workgroup Hubs Installation and User Guide 04/022.4 Bonus Port Configuration Options - RPMs and BPMs Figure 2.4a Magnum RPM Cards RPM-BNC, RPM-AUI Approx Figure 2.4c Physical Dimensions of Magnum Port ModulesApprox. 3 inches 7.6 cm Approx. 2 inches 5.1 cm 2.4.1 RPM-BNC 2.4.2 RPM-AUI 2.4.3 RPM-DTE 2.4.4 RPM-FST Fiber ST, Twist-lock ConnectorConnector JUMPER ACROSS not used 2.4.6 RPM-SMF Single-mode FiberMagnum RPM-SMF 2.4.7 RPM-TP Twisted Pair Magnum RPM-TP 2.4.9 BPM-AUI 2.4.8 BPM-BNCMagnum BPM-BNC Magnum BPM-AUI 2.4.11 BPM-TP 2.4.10 BPM-FSTMagnum BPM-FST 2.4.12 Special Option -- Second Bonus Port Models 1016 and Internal Universal Power Supply with Auto-ranging 2.5 Features and Benefits Low cost, stand-alone 10BASE-T connectivityLEDs Simplify Network Installation and Maintenance Workgroup connectivity into a larger network 2.6 Applications Figure 2.6a Magnum 1000 Workgroup Hub in stand-alone configurationMagnum 1000 Workgroup Hub BNC Segment RPM-BNC Server 1024 1024 10161008 Fiber BPM installed in any standard 19 inch rack 3.0 INSTALLATIONinstallation requires a Rack-mount Brackets 3.2 Powering the Magnum 1000 Workgroup Hub Media 3.3.1 Connecting Twisted Pair RJ-45, Unshielded or Shielded3.3 Ethernet Media Connections IEEE Standard 3.3.2 Connecting ThickNet 10BASE5 AUI 3.3.5 Connecting Fiber Optic 10BASE-FL and FOIRL ST-type, “Twist-Lock 3.3.3 Connecting ThinNet 10BASE2 BNC3.3.4 Connecting Drop Cable 10BASE5 DTE Table 3.3.2 AUI Pin Assignments at regular intervals you must use the color-coded strand on the 3.3.6 Connecting Fiber Optic SMA-type, Screw-on3.3.7 Connecting Single-Mode Fiber Optic SMF associated ports at each end of the fiber optic segment OPB Optical Power Budget = PTmin - PRmin 3.3.9 Rack-mounting consider as a standard for brackets are more popular inTELCO Industry and Rack-mounting purpose. The Collisions When carrier is detected simultaneously on multiple ports, a jam pattern is generated on each port to create a collision condition. When a collision signal from one port is detected, it generates a jam pattern to the other ports Figure 4.2b Internal Packet Filtered 4.2 Magnum 1000’s with BPM Local Bridge FunctionalityPacket Forwarded Forwarded MaintenanceFigure 4.2c External Packet Table 4.2 BPM Functionality 4.3 Power Requirements Figure 4.2e Local Segment Isolation with a Bridge Port Module BPM 5.0 TROUBLESHOOTING 5.1 Before Calling for Assistance 5.2 When Calling for Assistance 5.3 Return Material Authorization RMA Procedure GarrettCom, Inc 213 Hammond Ave Fremont, CA Attn. Customer Service APPENDIX A WARRANTY INFORMATIONNo Problem Found 5.4 Shipping and Packaging Information Power Supply Internal -48 VDC Option APPENDIX B Internal DC Power Supply OptionB1.0 SPECIFICATIONS - FOR MAGNUM 1000 WORKGROUP HUBS Power Supply Internal 24 VDC Option Figure B4.1 -48VDC Terminal B4.0 INSTALLATIONB3.0 APPLICATIONS Block on Magnum 1000’s-48VDC B4.1 UL Requirements B7.0 TROUBLESHOOTINGThe GND can be hooked at the last B5.0 OPERATION