GBC 640T 5. f e a t u r e

Page 5-1

640t – Installation and Operating Instructions

fil m sh a f t s

Fig. 5-2 Take-up and Supply Shafts.

A. Release Liner Take-up

Rewinds the release liner of pressure sensitive lms.

It consists of a shaft, core adapters, and cardboard

core.

B. Upper Unwind/Supply Shaft

Holds the upper medium supply on the laminator.

C. Lower Unwind/Supply Shaft

Holds the lower medium supply on the laminator.

5. fe a t u r e g u i d e

Fig. 5-1. Laminator Identication.

This chapter helps you identify the main components of the laminator.

Bottom supply shaft

Control panel

Safety sensor

Feed table

Top lm supply shaft

Release liner take-up

Roller pressure

handle

Feed table

interlock latch

(under table)

Pressure roller

Foot switch

Contents

Main Page Tab l e o f Co n T e n T s 1. Safety 2. Warranty 3. Specications 4. Installation Page W g ATTENTION CAUTION 1. s CUIDADO 640t Installation and Operating Instructions e 2. W li m i t e d 90-da y Wa r r a n t y Page Page 3-1 640t 3. s Fig. 3-1. 640t Dimensions (Shown in Inches (cm).) fcc n canada cla s s a no t i c e - av i s canada, cl a s s e a m 4. i pr i o r to i ns t a l l a t i o n i Page fil m sh a f t s A. Release Liner Take-up B. Upper Unwind/Supply Shaft C. Lower Unwind/Supply Shaft 5. f e a t u r e id l e r Ba r s , un W i n d sh a f t s , r e W i n d s d. u pp e r i rol l e r s a n d sa f e t y se n s o r a. u p p e r m a i n r B. l o W e r m a i n r e m e rg e n c y s t o p a n d t a. taB l e in t e r l o c k ho l e B. taB l e in t e r l o c k c. e me r g e n c y s d. f ro n t f eed t ten s i o n co n t r o l s a. r e l e a s e l i n e r t e n s i o n k B. upp e r fi l m te n s i o n knoB c. m e d i a r e W i n d e r t en s i o n k d. lo W e r fil m te n s i o n knoB me d i a core ad a p t e r r a. r e W i n d e r c ore a B. r e W i n d e r s c. r e W i n d e r c ar d B o a r d t p a. o n /of f p o W e r s B. c i r c u i t B c. n o m e n c l a t u r e p po W e r cord a n d fo o t sW i t c h c o n t r o l p tem p se c t io n s pe e d s Page 6. o g e n e r a l o lo a d i n g fi l m re m o v i n g a n d in s t a l l i n g t h e pr i n t cl a m p re m o v i n g a n d in s t a l l i n g t h e feed taB l e l oa d i n g f i l m o n t o t h e s u p p l y s To load lms onto the supply shafts: on page 6-5 7. Operator Maintenance on page 7-1 To remove existing lms: on page 6-4 thr e a d i n g fi l m W i t h a thr e a d i n g ca r d Removing and Installing the Feed Table on page 6-3. Removing and Installing the Feed Table on page 6-3 loa d i n g fi l m B y ta c k i n g neW fi l m t o ex i s t i n g fil m Removing and Installing the Feed Table on page 6-3 d e c a l i n g in t W o p m tip s fo r th r e a d i n g pr e s s u r e se n s i t i v e ad h e s i v e (psa) fi l m pre -co at i n g Bo a r d s m o u n t i n g o ro l l -t o -ro l l fil m al i g n m e n t a n d te n s i o n fil m al i g n m e n t fil m te n s i o n Testing the Web cle ar i ng a fi l m Ja m (Wr a p -u p ) Loading Film on page 6-2 la m i n a t i o n gui d e 7. o p e r a t o r m ca r i n g f o r t h e 640t la m i n a t o r c le an i n g t h e r Loading Film Onto the Supply Shafts on page 6-4 t Film Tension on page 6-10 Film Alignment on page 6-10 Loading Film on page 6-2. Cleaning the Rollers