GE 1019070, 1019071, 23954 2.2.2 Network command group

2.2.2 Network command group

The network command group allows to configure the board for communication over the network.

Command Parameters Description

showip Show the current network settings

arp Show ARP table

manual | dhcp | bootp

Define the network settings at boot-up (*)

manual static IP configuration, the device configuration

(ref. setip) is used

dhcp network settings retrieved from DHCP server

bootp network settings retrieved from BOOTP server

boot-method

setip

[address]

[netmask]

[gateway]

Set static IP/mask/default gateway

[address] IP-address

[netmask] Subnet mask

[gateway] Default gateway IP-address

NOTE: network settings can be specified manually only

when boot-method is set to manual

hostname [hostname] Define the full qualified domain name

[hostname] Full qualified domain name

dhcphost on | off Get the hostname from DHCP server

NOTE: This functionality is disabled (off) by default

As most network devices, SNMP/Web adapters use an auto-

negotiation protocol to communicate what media

technologies they support, and then select the fastest

mutually supported media technology.

recheck mii-tool

Running this command shows the negotiated media.

As most network devices, SNMP/Web adapters use an auto-

negotiation protocol to communicate what media

technologies they support, and then select the fastest

mutually supported media technology.

auto |

100baseTx-FD |

100baseTx-HD |

10baseT-FD |

10baseT-HD

speedduplex Some passive devices, such as single-speed hubs, are

unable to auto-negotiate. To handle such devices, the

SNMP/Web adapter can be forced to operate in one mode,

instead of auto-negotiating.

Quick network configuration menu

menu Running this command lunches an interactive menu –

follow the on-screen instructions

(*) NOTE: Network settings become effective only after a reboot. Therefore, if these settings must be

modified, the following actions shall be performed in sequence:

• Update the settings, using the applicable command

• Save the settings – nvsave command. Always remember that unsaved setting are lost in case

of reset / reboot

• Reboot the card – reboot command

Modifications reserved Page 15/58

OPM_CNT_SNM_BAS_CRD_1GB_V012.doc Operating Manual SNMP/Web Adapter

Contents

Main GE Digital Energy Power Quality Operating Manual SNMP / WEB ADAPTER GE imagination at work Page g Table of contents Page Page 1 INTRODUCTION 1.1 FEATURES 1.2 OVERVIEW Page Page 1.3 ARCHITECTURE 1.4 SAFETY 2 CONSOLE INTERFACE 2.1 INTRODUCTION 2.1.1 Local connection 2.1.2 Remote connection 2.1.3 Log-on 2.1.4 Saving the settings 2.2 COMMAND LIST 2.2.1 General command group 2.2.2 Network command group 2.2.3 DNS command group 2.2.4 User command group 2.2.5 Service command group 2.2.6 Time command group 2.2.7 Smtp command group 2.2.8 Snmp command group 2.2.9 Trap command group 2.2.10 UPS command group 2.2.11 Rccmd command group 2.2.12 Events command group 2.2.13 Log command group 3 WEB INTERFACE 3.1 INTRODUCTION 3.1.1 Supported browsers 3.1.2 Initial web access 3.1.3 Sample page 3.2 NAVIGATION BAR 3.3 UPS SECTION 3.3.1 UPS Identification page 3.3.2 Battery page The Battery page shows the following information. 3.3.3 UPS Status page The UPS status page shows the following information for each of the input / output / bypass lines. Also the following information is presented: Finally, a 3-ph system featuring the PMAD functionality will also show the following: 3.3.6 UPS Test page 3.3.7 UPS Control page (1-ph/SP units ONLY) 3.3.8 UPS Config page 3.4 SYSTEM SECTION 3.4.1 Network page 3.4.2 Date&Time page 3.4.3 RCCMD page 3.4.4 Password page 3.5 SNMP SECTION 3.5.1 SNMP settings page 3.5.2 Trap settings page 3.5.3 Alarm notification page 3.6 SMTP SECTION 3.6.1 SMTP configuration page 3.6.2 Alarm notification page 3.7 LOG SECTION 3.8 UTILITY SECTION 3.9 SAVE SECTION 3.10 USER SECTION 4 SNMP AGENT 4.1 MIB STRUCTURE 4.2 RFC1628 MIB OBJECTS Page 4.3 GE MIB OBJECTS Page 5 NETWORK CONFIGURATION 5.1 ETHERNET CONNECTION 5.2 TCP/IP CONFIGURATION 5.2.1 Static IP address 5.2.2 BOOTP / DHCP 5.3 DNS CONFIGURATION 5.4 HOSTNAME 6 MULTI-SERVER NETWORK SHUTDOWN (RCCMD) 6.1 NETWORK SHUTDOWN WITH RCCMD 6.1.1 Set-up and Configuration of controlled Servers 6.1.2 Configuration of the SNMP/Web adapter 6.1.3 Network configuration 6.1.4 RCCMD Shutdown 6.2 RCCMD CLIENT RELAY 7 SECURITY 7.1 USER AUTHENTICATION & AUTHORISATION 7.1.1 User Management 7.1.2 User class 7.1.3 Selective service activation 7.2 SERVICES (ACCESS METHODS) 7.3 ENCRYPTION 7.3.1 SSH and SFTP Page 7.3.2 SSL Certificates Page 7.4 CUSTOMER RESPONSIBILITY 7.4.1 Physical security 7.4.2 Changing default configuration 7.4.3 User & Service management 7.4.4 Encryption 8 OTHER FUNCTIONALITIES 8.1 SYSTEM TIME 8.2 SERIAL BY-PASS (1-PH/SP VERSION ONLY) 8.3 HTTP BASED MONITORING (1-PH/SP VERSION ONLY) 8.3.1 UPS Load Alert 9 MAINTENANCE 9.1 SOFTWARE UPGRADE 9.2 CONFIGURATION FILE 9.3 LOGS 10 TROUBLESHOOTING 10.1 TROUBLESHOOTING UPS CONNECTION 10.1.1 3-ph SNMP/Web plug-in adapter 10.1.2 1-ph SNMP/Web external adapter 10.2 TROUBLESHOOTING LOCAL CONNECTION 10.3 TROUBLESHOOTING NETWORK CONNECTION 10.4 TROUBLESHOOTING WEB ACCESS 10.5 TROUBLESHOOTING DATE&TIME (NTP) 10.6 TROUBLESHOOTING E-MAIL NOTIFICATION (SMTP) 10.7 TROUBLESHOOTING NETWORK SHUTDOWN 11 CUSTOMER SUPPORT 11.1 FIRST LINE SUPPORT 11.2 INTERNET 11.3 WWW SERVER