GE 1019070, 1019071, 23954 4.3 GE MIB OBJECTS

4.3 GE MIB OBJECTS

GE provides private MIBs, which enhance the UPS information available over SNMP interface.

These MIBs are only supported on 3-ph SNMP/Web plug-in adapter.

Two different version of the GE private MIB exist:

• GE Single MIB: to be used for monitoring of a 3-ph UPS is single unit configuration

• GE Parallel MIB: to be used for monitoring of a 3-ph parallel UPS system

The MIB structure is shown in the following picture. The geGenericUPS group provides information on

the unit in stand-alone configuration or on the overall system in a parallel configuration. The geFirstUPS

… geEightUPS groups provide information on the units that are part of a parallel configuration.

For each of these groups the 3-ph SNMP/Web plug-in adapter supports the following objects.

(Objects marked with [*] do not have a RFC1628 correspondence)

OIDs TRAPS & ALARMS

==== upsIdent Group ====

upsIdentManufacturer

upsIdentModel

upsIdentUPSSoftwareVersion

upsIdentAgentSoftwareVersion

upsIdentName

upsIdentAttachedDevices

upsIdentsUPSSerialNumber [*]

upsIdentComProtVersion [*]

upsIdentOperatingTime [*]

==== uspBattery Group ====

upsBatteryStatus

upsSecondsOnBattery

upsEstimatedMinutesRemaining

upsEstimatedChargeRemaining

upsBatteryVoltage

upsBatteryCurrent

upsBatteryTemperature

upsBatteryRipple [*]

==== upsInput Group ====

upsInputLineBads

upsInputNumLines

upsInputFrequency

==== geUPSTraps & upsWellKnownAlarms group

====

upsAlarmBatteryBad

upsAlarmOnBattery

upsAlarmLowBattery

upsAlarmDepletedBattery

upsAlarmTempBad

upsAlarmInputBad

upsAlarmOutputBad

upsAlarmOutputOverload

upsAlarmOnBypass

upsAlarmBypassBad

upsAlarmOutputOffAsRequested

upsAlarmUpsOffAsRequested

upsAlarmChargerFailed

upsAlarmUpsOutputOff

upsAlarmUpsSystemOff

upsAlarmFanFailure

geUPS(1.3.6.1.4.1.818.1.1)

geGenericUPS(10)

geFirstUPS(11)

geSecondUPS(12)

…

geEigthUPS(18)

Parallel

system

only

geUPS(1.3.6.1.4.1.818.1.1)

geGenericUPS(10)

geFirstUPS(11)

geSecondUPS(12)

…

geEigthUPS(18)

Parallel

system

only

upsAlarmFuseFailure

upsAlarmGeneralFault

upsAlarmDiagnosticTestFailed

upsAlarmCommunicationsLost

upsAlarmAwaitingPower

upsAlarmShutdownPending

upsAlarmShutdownImminent

Modifications reserved Page 37/58

OPM_CNT_SNM_BAS_CRD_1GB_V012.doc Operating Manual SNMP/Web Adapter

Contents

Main GE Digital Energy Power Quality Operating Manual SNMP / WEB ADAPTER GE imagination at work Page g Table of contents Page Page 1 INTRODUCTION 1.1 FEATURES 1.2 OVERVIEW Page Page 1.3 ARCHITECTURE 1.4 SAFETY 2 CONSOLE INTERFACE 2.1 INTRODUCTION 2.1.1 Local connection 2.1.2 Remote connection 2.1.3 Log-on 2.1.4 Saving the settings 2.2 COMMAND LIST 2.2.1 General command group 2.2.2 Network command group 2.2.3 DNS command group 2.2.4 User command group 2.2.5 Service command group 2.2.6 Time command group 2.2.7 Smtp command group 2.2.8 Snmp command group 2.2.9 Trap command group 2.2.10 UPS command group 2.2.11 Rccmd command group 2.2.12 Events command group 2.2.13 Log command group 3 WEB INTERFACE 3.1 INTRODUCTION 3.1.1 Supported browsers 3.1.2 Initial web access 3.1.3 Sample page 3.2 NAVIGATION BAR 3.3 UPS SECTION 3.3.1 UPS Identification page 3.3.2 Battery page The Battery page shows the following information. 3.3.3 UPS Status page The UPS status page shows the following information for each of the input / output / bypass lines. Also the following information is presented: Finally, a 3-ph system featuring the PMAD functionality will also show the following: 3.3.6 UPS Test page 3.3.7 UPS Control page (1-ph/SP units ONLY) 3.3.8 UPS Config page 3.4 SYSTEM SECTION 3.4.1 Network page 3.4.2 Date&Time page 3.4.3 RCCMD page 3.4.4 Password page 3.5 SNMP SECTION 3.5.1 SNMP settings page 3.5.2 Trap settings page 3.5.3 Alarm notification page 3.6 SMTP SECTION 3.6.1 SMTP configuration page 3.6.2 Alarm notification page 3.7 LOG SECTION 3.8 UTILITY SECTION 3.9 SAVE SECTION 3.10 USER SECTION 4 SNMP AGENT 4.1 MIB STRUCTURE 4.2 RFC1628 MIB OBJECTS Page 4.3 GE MIB OBJECTS Page 5 NETWORK CONFIGURATION 5.1 ETHERNET CONNECTION 5.2 TCP/IP CONFIGURATION 5.2.1 Static IP address 5.2.2 BOOTP / DHCP 5.3 DNS CONFIGURATION 5.4 HOSTNAME 6 MULTI-SERVER NETWORK SHUTDOWN (RCCMD) 6.1 NETWORK SHUTDOWN WITH RCCMD 6.1.1 Set-up and Configuration of controlled Servers 6.1.2 Configuration of the SNMP/Web adapter 6.1.3 Network configuration 6.1.4 RCCMD Shutdown 6.2 RCCMD CLIENT RELAY 7 SECURITY 7.1 USER AUTHENTICATION & AUTHORISATION 7.1.1 User Management 7.1.2 User class 7.1.3 Selective service activation 7.2 SERVICES (ACCESS METHODS) 7.3 ENCRYPTION 7.3.1 SSH and SFTP Page 7.3.2 SSL Certificates Page 7.4 CUSTOMER RESPONSIBILITY 7.4.1 Physical security 7.4.2 Changing default configuration 7.4.3 User & Service management 7.4.4 Encryption 8 OTHER FUNCTIONALITIES 8.1 SYSTEM TIME 8.2 SERIAL BY-PASS (1-PH/SP VERSION ONLY) 8.3 HTTP BASED MONITORING (1-PH/SP VERSION ONLY) 8.3.1 UPS Load Alert 9 MAINTENANCE 9.1 SOFTWARE UPGRADE 9.2 CONFIGURATION FILE 9.3 LOGS 10 TROUBLESHOOTING 10.1 TROUBLESHOOTING UPS CONNECTION 10.1.1 3-ph SNMP/Web plug-in adapter 10.1.2 1-ph SNMP/Web external adapter 10.2 TROUBLESHOOTING LOCAL CONNECTION 10.3 TROUBLESHOOTING NETWORK CONNECTION 10.4 TROUBLESHOOTING WEB ACCESS 10.5 TROUBLESHOOTING DATE&TIME (NTP) 10.6 TROUBLESHOOTING E-MAIL NOTIFICATION (SMTP) 10.7 TROUBLESHOOTING NETWORK SHUTDOWN 11 CUSTOMER SUPPORT 11.1 FIRST LINE SUPPORT 11.2 INTERNET 11.3 WWW SERVER