GE 1019070, 1019071, 23954 2.2.10 UPS command group

2.2.10 UPS command group

The UPS command group allows monitoring and configuration of the managed UPS system.

Command Parameters Description

upsinfo (*) Show detailed UPS information

upstest (*) Start/Stop UPS tests

upscontrol (*) Control the UPS (1-ph/SP versions ONLY)

upsconfig (*) Configure UPS parameters

attacheddevice [device]

Set UPS attached device

[device] Device which is powered/protected by the UPS

NOTE: Maximum length 63 chars. If this parameter contain

blanks or special characters it shall be specified in between

double quotation marks (“...”)

alarmdelay [time]

Set alarm delay time (1-ph/SP version ONLY)

[time] Time in seconds before alarm notification

NOTE: This parameters is factory set to its ideal value and

shall not be changed unless instructed to do so

retrydelay [time]

Set retry delay time (1-ph/SP version ONLY)

[time] Time in seconds between re-connection attempts

NOTE: This parameters is factory set to its ideal value and

shall not be changed unless instructed to do so

retrycount [count]

Set retry count (1-ph/SP version ONLY)

[count] Number of re-connection attempts

NOTE: This parameters is factory set to its ideal value and

shall not be changed unless instructed to do so

serialbypass on | off

Enable/disable the serialbypass functionality

NOTE: This command is offered for UPS service access ONLY.

It use outside of this scope is not recommended (enabling

this functionality stops the UPS monitoring

Show/Set card address on the IMV bus

[address] Card address in the range 0, 54-57

NOTE: This setting may overrides the HW setting through the

dip-switches on the card. Setting this parameter to 0 reverts

to the HW settings.

This setting becomes active only after reboot (save the

settings!)

[address] cardaddress

Enable/disable write commands to the UPS

Setting readonlymode to on will stop any write operation

towards the UPS (the SNMP/Web adapter will effectively

switch to read-only mode). The UPS Test, Control and Config

web pages will not be shown in the navigator bar.

[on | off] readonlymode

Caution! Once enabled, this setting may not be reverted.

NOTE: 1-ph/SP versions ONLY

Modifications reserved Page 23/58

OPM_CNT_SNM_BAS_CRD_1GB_V012.doc Operating Manual SNMP/Web Adapter

Contents

Main GE Digital Energy Power Quality Operating Manual SNMP / WEB ADAPTER GE imagination at work Page g Table of contents Page Page 1 INTRODUCTION 1.1 FEATURES 1.2 OVERVIEW Page Page 1.3 ARCHITECTURE 1.4 SAFETY 2 CONSOLE INTERFACE 2.1 INTRODUCTION 2.1.1 Local connection 2.1.2 Remote connection 2.1.3 Log-on 2.1.4 Saving the settings 2.2 COMMAND LIST 2.2.1 General command group 2.2.2 Network command group 2.2.3 DNS command group 2.2.4 User command group 2.2.5 Service command group 2.2.6 Time command group 2.2.7 Smtp command group 2.2.8 Snmp command group 2.2.9 Trap command group 2.2.10 UPS command group 2.2.11 Rccmd command group 2.2.12 Events command group 2.2.13 Log command group 3 WEB INTERFACE 3.1 INTRODUCTION 3.1.1 Supported browsers 3.1.2 Initial web access 3.1.3 Sample page 3.2 NAVIGATION BAR 3.3 UPS SECTION 3.3.1 UPS Identification page 3.3.2 Battery page The Battery page shows the following information. 3.3.3 UPS Status page The UPS status page shows the following information for each of the input / output / bypass lines. Also the following information is presented: Finally, a 3-ph system featuring the PMAD functionality will also show the following: 3.3.6 UPS Test page 3.3.7 UPS Control page (1-ph/SP units ONLY) 3.3.8 UPS Config page 3.4 SYSTEM SECTION 3.4.1 Network page 3.4.2 Date&Time page 3.4.3 RCCMD page 3.4.4 Password page 3.5 SNMP SECTION 3.5.1 SNMP settings page 3.5.2 Trap settings page 3.5.3 Alarm notification page 3.6 SMTP SECTION 3.6.1 SMTP configuration page 3.6.2 Alarm notification page 3.7 LOG SECTION 3.8 UTILITY SECTION 3.9 SAVE SECTION 3.10 USER SECTION 4 SNMP AGENT 4.1 MIB STRUCTURE 4.2 RFC1628 MIB OBJECTS Page 4.3 GE MIB OBJECTS Page 5 NETWORK CONFIGURATION 5.1 ETHERNET CONNECTION 5.2 TCP/IP CONFIGURATION 5.2.1 Static IP address 5.2.2 BOOTP / DHCP 5.3 DNS CONFIGURATION 5.4 HOSTNAME 6 MULTI-SERVER NETWORK SHUTDOWN (RCCMD) 6.1 NETWORK SHUTDOWN WITH RCCMD 6.1.1 Set-up and Configuration of controlled Servers 6.1.2 Configuration of the SNMP/Web adapter 6.1.3 Network configuration 6.1.4 RCCMD Shutdown 6.2 RCCMD CLIENT RELAY 7 SECURITY 7.1 USER AUTHENTICATION & AUTHORISATION 7.1.1 User Management 7.1.2 User class 7.1.3 Selective service activation 7.2 SERVICES (ACCESS METHODS) 7.3 ENCRYPTION 7.3.1 SSH and SFTP Page 7.3.2 SSL Certificates Page 7.4 CUSTOMER RESPONSIBILITY 7.4.1 Physical security 7.4.2 Changing default configuration 7.4.3 User & Service management 7.4.4 Encryption 8 OTHER FUNCTIONALITIES 8.1 SYSTEM TIME 8.2 SERIAL BY-PASS (1-PH/SP VERSION ONLY) 8.3 HTTP BASED MONITORING (1-PH/SP VERSION ONLY) 8.3.1 UPS Load Alert 9 MAINTENANCE 9.1 SOFTWARE UPGRADE 9.2 CONFIGURATION FILE 9.3 LOGS 10 TROUBLESHOOTING 10.1 TROUBLESHOOTING UPS CONNECTION 10.1.1 3-ph SNMP/Web plug-in adapter 10.1.2 1-ph SNMP/Web external adapter 10.2 TROUBLESHOOTING LOCAL CONNECTION 10.3 TROUBLESHOOTING NETWORK CONNECTION 10.4 TROUBLESHOOTING WEB ACCESS 10.5 TROUBLESHOOTING DATE&TIME (NTP) 10.6 TROUBLESHOOTING E-MAIL NOTIFICATION (SMTP) 10.7 TROUBLESHOOTING NETWORK SHUTDOWN 11 CUSTOMER SUPPORT 11.1 FIRST LINE SUPPORT 11.2 INTERNET 11.3 WWW SERVER