Openings for input and output cable connections | GE 300, 225

g

GE

Openings for input and output cable connections

S

U

1

0

_

p

to

w

ie

v

S

P

U

_

0

0

-3

5

2

2

_

S

G

S

64.96"
1,650mm	6.30"	1.58"
	160mm	1.58"
		40mm

Battery

		"
	6
.7		m
2
	m
0
7

Utility input

Output Load

				"
			6					"
	.6							"
1				m			0
2				m		.5
			m		1			m
		0			3			m
5							m
5						0
					0
					8

SG Series openings are provided on the top and the bottom of the UPS for the connection of input and output cables.

Fig. 3.4.1-2 Opening on top of the cabinet for input and output cables

																					0				64.96"
																					0			S	1,650mm
																							U
																				_		2
																			m
																		tto
																	o
																b									Utility input
										U					w
										U				ie
													v
												S
									_		P
		_						0																	Output Load
							0
						-3
					5
				2
S	S		2																											6.30"
G																														160mm							1.77"
																														160mm							1.77"
																																			45mm
																																		"
																																	6
																															.6
																														1				m				"
																														2				m				"
																																	m				0
																																0				.5
																														5					1			m
																														5					3			m
																																					m
																																				0
																											"								0
																											"								8
																										4				m
																									.9					m
																									3				m
																												0
																											0
																										1

Fig. 3.4.1-3 Opening on the bottom of the cabinet for input and output cables

Pay attention to the position of these

openings, when choosing the placement of the UPS.

These openings are

covered with a protective plate.

Fixing of the UPS cabinet on the floor

The UPS cabinet is free standing and normally does not require to be bolted to the floor.

The UPS cabinet can be fixed however to the floor by bolting it with the supporting blocks to the floor.

See Fig. 3.4.1-4.

1.378"	62.205"
35mm	1580mm

Ø 0.47305"	=
Ø 12mm

28.071"

713mm

=

SGS_225-300_UPS view bottom_02US

1.378"

35mm

2.363"	60mm
26.772"	680mm

2.363"

60mm

Front side

Fig. 3.4.1-4 Fixing of the UPS cabinet on the floor

OPM_SGS_ISG_M22_M30_0US_V011.doc

13/38

Installation Guide SG Series 225 & 300 kVA

Image 13

GE 300, 225 manual Openings for input and output cable connections, Fixing of the UPS cabinet on the floor

Contents

SG Series Systems Copyright 2003 by GE Industrial Systems Start UP and Commissioning Dear Customer Preface Table of contents Battery InstallationGeneral Storage Safety instructions when working with battery Safety warnings Safety symbols and warningsRisk of electric shock PE Earth GND Ground Protective Grounding Terminal Layout SG Series 225 and 300 KVA Layout Weight SG Series 225 and 300 kVA Dimensions and weightTransport Forklift Crane Transport UPS only in upright position Delivery Storage of BatteryStorage of the UPS Positioning of the UPS SG Series Place of InstallationCheck -26A of the NEC code for specific requirements Fixing of the UPS cabinet on the floor Openings for input and output cable connections 1-5 RPA system disposition Battery location CFM Ventilation and Cooling Unpacking Take care not to damage the UPS when moving by forkliftPacking material recycling Separate input Rectifier & Bypass recommended Electrical WiringCommon input Rectifier & Bypass Neutral current could be greater than the phase currents Input/output over current protection and wire sizing Phase, 4 wire plus Ground Phase, 3 wire plus GroundWire positive and negative plus Ground See .7.1-1 Copper Wire Size Range Wiring Connection 1-1 Access to the input / output connections Common Input Rectifier / Bypass Power connection with common input utilityOutput Load Cable section for this connection shall be not less then AWG L1-1 Rectifier Phase a L1-2 Power connection separate input utilityL2-1 Rectifier Phase B L2-2 L3-1 Rectifier Phase C L3-2 BR1 Battery Battery connectionPositive pole of the Battery Do not insert the Battery Fuses before the commissioning Manual Bypass, serious damage to the Load could result Setup for SG Series when functioning as frequency converter 1 RPA Parallel System Power Wiring of Parallel Units Parallel Control BUS Connection UPS Intermediate units Terminal units Control BUS Cable Location Access to the control bus connectionControl bus cables connection Interface IM0048 going to P13 11-3 Control Bus cable routing and connection Control bus cables routing Customer Interface Customer Interface 18, 19 Or J2 20, 21 NO, C, NC Acoustic Alarm 15, 16 Or J2 17, 18 NO, C, NC General AlarmOutput potential free contacts Or J2 / 1, 2 NO, C, NC Utility Failure GND JP3 EPO Emergency Power Off Input contact 38/38