Terminal units, Intermediate units | GE 300, 225 instruction

g

GE

SGT5000_100-150_RPA-IM0048_02

JB1 JP1

IM 0048

JP2

JP1

JP4

JP2

JB

JP3

JA1 JP4 JA

JP3

Fig. 3.10-2 Bus connection on terminal units

Terminal units

On the parallel bus PCB “P34 – Bus Interface IM0048”, of the first and last units (terminal) of the parallel system the Jumpers JP1, JP2, JP3 and JP4 must be inserted.

SGT5000_100-150_RPA-IM0048_03

JB1	JP1
JB2	IM 0048

JP2

JP1

JP4

JP3

JP2

JB

JA1	JP4	JA
JA2	JP3

Fig. 3.10-3 Bus connection on intermediate units

Intermediate units

On the parallel bus PCB “P34 – Bus Interface IM0048” of the intermediate units of the parallel system the Jumpers JP1, JP2, JP3 and JP4 must be removed.

In a parallel system composed of 2 or more units, only the first and last units (having 1 input JA and JB free) have the Jumper JP1, JP2, JP3 and JP4 inserted on parallel bus PCB “P34 – Bus Interface IM0048” (see Fig. 3.10-2).

OPM_SGS_ISG_M22_M30_0US_V011.doc

31/38

Installation Guide SG Series 225 & 300 kVA

Image 31

GE 300, 225 manual Terminal units, Intermediate units

Contents

SG Series Systems Copyright 2003 by GE Industrial Systems Start UP and Commissioning Dear Customer Preface Table of contents Storage InstallationBattery General Safety instructions when working with battery Protective Grounding Terminal Safety symbols and warningsSafety warnings Risk of electric shock PE Earth GND Ground Layout SG Series 225 and 300 KVA Layout Transport UPS only in upright position Dimensions and weightWeight SG Series 225 and 300 kVA Transport Forklift Crane Delivery Storage of BatteryStorage of the UPS Positioning of the UPS SG Series Place of InstallationCheck -26A of the NEC code for specific requirements Fixing of the UPS cabinet on the floor Openings for input and output cable connections 1-5 RPA system disposition Battery location CFM Ventilation and Cooling Unpacking Take care not to damage the UPS when moving by forkliftPacking material recycling Separate input Rectifier & Bypass recommended Electrical WiringCommon input Rectifier & Bypass Neutral current could be greater than the phase currents Input/output over current protection and wire sizing See .7.1-1 Phase, 3 wire plus GroundPhase, 4 wire plus Ground Wire positive and negative plus Ground Copper Wire Size Range Wiring Connection 1-1 Access to the input / output connections Common Input Rectifier / Bypass Power connection with common input utilityOutput Load Cable section for this connection shall be not less then AWG L3-1 Rectifier Phase C L3-2 Power connection separate input utilityL1-1 Rectifier Phase a L1-2 L2-1 Rectifier Phase B L2-2 BR1 Do not insert the Battery Fuses before the commissioning Battery connectionBattery Positive pole of the Battery Manual Bypass, serious damage to the Load could result Setup for SG Series when functioning as frequency converter 1 RPA Parallel System Power Wiring of Parallel Units Parallel Control BUS Connection UPS Intermediate units Terminal units Interface IM0048 going to P13 Access to the control bus connectionControl BUS Cable Location Control bus cables connection 11-3 Control Bus cable routing and connection Control bus cables routing Customer Interface Customer Interface Or J2 / 1, 2 NO, C, NC Utility Failure 15, 16 Or J2 17, 18 NO, C, NC General Alarm18, 19 Or J2 20, 21 NO, C, NC Acoustic Alarm Output potential free contacts GND JP3 EPO Emergency Power Off Input contact 38/38