Manuals / GE / Computer Equipment / Webcam

GE BECCO2200 manual Configuring the A164PORT Table, General Information, Description of Fields

Models: BECCO2200

1 61

Download 61 pages 14.91 Kb

Page 25

Image 25

Chapter 4: Configuring the A164PORT Table

This chapter describes the configurable parameters in the Communication Port Configuration Table (A164PORT).

4.1General Information

The A164PORT table provides information for the operation of the BECO2200 DCA’s communication port(s). One record is required for every communication port configured.

4.2Description of Fields

Where applicable, Table 4 describes the field name, range, special case, and typical value for each field of the A164PORT table. Following the table is a textual description of each field’s meaning.

Table 4 BECO2200 DCA A164PORT Configuration Table

	Field		Range	Special		Typical

	Communication Port	COM1..COM9		COM0 is typically reserved for		COM1
	Name	COMA..COMZ		WESMAINT

	Communication Port	0	= None	N/A		1 = Even Parity
	Parity	1	= Even
		2	= Odd

	Baud rate	110, 300, 600, 1200,		N/A		4800 or 9600
		2400, 4800, 9600

	RTS On Time	0..65535		Must be at least 1 if modem		N/A
				signals are used



Restricted				A164-0CG-1.00-2
Full					9
					9

Page 25

Image 25

GE BECCO2200 manual Configuring the A164PORT Table, General Information, Description of Fields

Contents

GE Energy Services Configuration GuideBECCO2200 DCA A164-0CGGE Energy Services Configuration GuideNOTICE OF COPYRIGHT & PROPRIETARY RIGHTS TRADEMARK NOTICESChapter 1 Configuration Tables Table of ContentsChapter 2 Configuring Win for the BECO2200 DCA Chapter 3 Configuring the A164APPL TableChapter 5 Configuring the A164UNIT Table Chapter 4 Configuring the A164PORT TableChapter 6 Configuring the A164MODE Table Chapter 7 Configuring the A164DVCF Configuration TableAppendix A Messages Logged by the BECO2200 DCA Chapter 8 Configuring the A164DTBL Configuration TableGlossary of Terms List of Acronyms and Abbreviations GE Energy Services Configuration GuideBECCO2200 DCA A164-0CG-1.00-2Configuration Guide List of FiguresGE Energy Services BECCO2200 DCAConfiguration Guide viiiGE Energy Services BECCO2200 DCAList of Tables GE Energy Services Configuration GuideBECCO2200 DCA A164-0CG-1.00-2Purpose of this Guide About this GuideWho Should Use this Guide WESMAINT II Maintenance Facility Configuration Guide B014-0CG.D20 WESMAINT II Maintenance Facility User’s Guide B014-0UG.D20Config Pro Configuration System User’s Guide P012-0UG WESDAC Configuration System User’s Guide P005-0UGxiii How this Guide is OrganizedGE Energy Services Configuration GuideBECCO2200 DCA A164-0CG-1.00-2Overview Configuration Guide Figure 1 System OverviewMaster Station Interface1.1 BECO2200 DCA Configuration Tables Chapter 1 Configuration TablesTable 1 BECO2200 DCA Configuration Tables 1.2 Configuration Sequence2.1 WESDAC Point Allocation Chapter 2 Configuring Win for the BECO2200 DCATable 2 Required Points BECO2200 Device 2.1.2 Binary Outputs 2.1.1 Binary Inputs2.1.3 Counters 2.1.4 Analog InputsTable 3 BECO2200 DCA A164APPL Configuration Table Chapter 3 Configuring the A164APPL Table3.1 General Information 3.2 Description of Fields3.2.3 SOE Buffer Size Adjustment 3.2.2 Reply Buffer Size Adjustment3.2.1 DCA Index 3.2.4 SOE Buffer Overflow Option3.2.5 Device Event Response Time GE Energy Services Configuration GuideBECCO2200 DCA A164-0CG-1.00-2RestrictedTable 4 BECO2200 DCA A164PORT Configuration Table Chapter 4 Configuring the A164PORT Table4.1 General Information 4.2 Description of Fields4.2.2 Communication Port Parity 4.2.1 Communication Port Name4.2.3 BAUD Rate 4.2.4 RTS On Time4.2.7 Remote Reply Timeout 4.2.6 Intercharacter Timeout4.2.5 RTS Off Time Table 5 Character Times at the Supported BAUD Rates4.2.9 Retries Before Failure 4.2.8 Line Idle Time4.2.10 Failures Before Off-line 4.2.11 Number of Devices on PortTable 6 BECO2200 DCA A164UNIT Configuration Table Chapter 5 Configuring the A164UNIT Table5.1 General Information 5.2 Description of Fields5.2.2 Unit Type 5.2.1 Remote Address5.2.3 Type 0 Read Interval 5.2.5 Type 2 Read Interval 5.2.4 Type 1 Read Interval5.2.6 Type 3 Read Interval 5.2.7 Type 4 Read Interval5.2.11 Type 8 Read Interval 5.2.10 Type 7 Read Interval5.2.12 Time Synchronization Interval 6.1 General Information Chapter 6 Configuring the A164MODE Table6.2 Description Of Fields Table 7 BECO2200 DCA A164MODE Configuration Table6.2.1 First DVCF Figure 2 Relationship between A164MODE, A164UNOT. And A164FTBL Tables6.2.2 Number of DVCF GE Energy Services Configuration GuideBECCO2200 DCA A164-0CG-1.00-2RestrictedTable 8 BECO2200 DCA A164DVCF Configuration Table Chapter 7 Configuring the A164DVCF Configuration Table7.1 General Information 7.2 Description of Fields7.2.2 Number of Units 7.2.1 First Unit7.2.3 First Data Record 7.2.4 Number of Data RecordsTable 9 BECO2200 DCA A164DTBL Configuration Table Chapter 8 Configuring the A164DTBL Configuration Table8.1 General Information 8.2 Description of Fields8.2.2 Point Number 8.2.1 Table Type8.2.3 Data Value Appendix AMessages Logged by the BECO2200 DCA A.1 Fatal Error MessagesA164 A164-x-yCause F100 Bad A164APPL record counts, must beRemedy F101 Bad A164PORT record counts, must beF105 Invalid SOE Overflow parameter F107 x WESDACy pnts configured, z requiredF106 Total # devices exceeds UNIT size Table 10 WESDAC Number DefinitionsF110 Fatal errors exist in configuration F108 x table creation errorF109 Cannot find x database table F111 Bad A164DVCF record counts, must beF121 Mode Record x, invalid Number of DVCF F120 Mode Record x, invalid First DVCFF122 DVCF Record x, invalid First Unit F123 DVCF Record x, invalid Number of UnitsF201 Error x signaling A164-D-00 process F200 Error x on win openF203 Error x creating A164-y-z exchange F125 DVCF Record x, invalid Number of Type-PointF205 Error x activating A164-y-z process F204 Error x spawning A164-y-z processF206 Process A164-x-y died while initializing F207 Unable to allocate buffersE300 PORT rec x, invalid baud rate A.2 Non-Fatal Error MessagesE301 PORT rec x, invalid failures before offline E302 PORT rec x, num of devices exceeds UNITE307 UNIT rec x, configuration bad E303 PORT rec x, configuration badE304 PORT rec x, invalid unit address E305 UNIT rec x, invalid unit typeE400 Error x opening port y E399 Non-fatal errors exist in configurationE401 Error x setting character port E308 PORT rec x, num of devices cannot =E403 Error x creating A164-y-z exchange E402 Error x setting SIO timersE404 Error x spawning A164-y-z process E405 Error x activating A164-y-z processE409 Error x, invalid start signal from Spawner E407 Error x signalling A164-y-z processE406 Process A164-x-y died while initializing E408 Unable to allocate polling listW502 Error x on jamx to A164-C-y W503 Error x on waitv from A164-C-y W500 Error x on sendx to A164-D-00 W501 Error x on sendx to A164-C-yW504 Error x signaling back response W505 Error x on reqx W600 Error x on win read W601 Error x on ACK/NACK win writeW609 Error x on WES6 CHANGETRANS win write W608 Error x on WESy INITPOINT win writeW610 Error x on WES6 CHANGEFAILS win write W611 Error x on WES6 CHANGERETRIES win writeI704 No Configuration - deleting I703 PORT rec x, invalid intercharacter timeoutI705 PORT rec x, no polling required EffectDemand Scan Failed A.5 Output Request Return CodesDO Operate Failed AO Operate FailedGlossary of Terms Data-collection Interface Node GE Energy Services Configuration GuideBECCO2200 DCA A164-0CG-1.00-2RestrictedList of Acronyms and Abbreviations