Remote Address, Unit Type, Type 0 Read Interval | GE BECCO2200

						BECCO2200 DCA
GE Energy Services						Configuration Guide

	Field		Range		Special	Typical

	Type 2 Read Interval		< 0 - Demand Only		N/A	10
	(seconds)		= 0 - Continuous
			> 0 - Interval

	Type 3 Read Interval		< 0 - Demand Only		Use Type 7 Read	-1
	(seconds)		= 0 - Continuous		Instead
	(seconds)		= 0 - Continuous
			> 0 - Interval

	Type 4 Read Interval		< 0 - Demand Only		N/A	10
	(seconds)		= 0 - Continuous
			> 0 - Interval

	Type 5 Read Interval		< 0 - Demand Only		N/A	10
	(seconds)		= 0 - Continuous
			> 0 - Interval

	Type 6 Read Interval		< 0 - Demand Only		N/A	10
	(seconds)		= 0 - Continuous
			> 0 - Interval

	Type 7 Read Interval		< 0 - Demand Only		N/A	10
	(seconds)		= 0 - Continuous
			> 0 - Interval

	Type 8 Read Interval		< 0 - Demand Only		N/A	10
	(seconds)		= 0 - Continuous
			> 0 - Interval

	Time Synchronization		£ 0 - Demand Only		N/A	600
	Interval (seconds)		> 0 - Interval
			> 0 - Interval

5.2.1 Remote Address

This parameter specifies the remote address programmed at the unit. Each unit on the same communication port must be given a unique address. -1 is used to indicate a SPARE device. Spare devices are allocated WESDAC points, as described in Chapter 2: but no communication is ever initiated to the device.

5.2.2 Unit Type

This parameter specifies the type of unit. Only BECO2200-M-0420 Control Relay is supported.

5.2.3 Type 0 Read Interval

This parameter specifies, in seconds, the minimum interval between Type 0 Read requests issued to the device. A negative number configured indicates that no timed scans of this type are required for this device. The device may, at any time, be scanned through the activation of the Type 0 Read Pseudo Control.

A164-0CG-1.00-2Restricted

14	Full

Image 30

GE BECCO2200 manual Remote Address, Unit Type, Type 0 Read Interval

Contents

Configuration Guide BECCO2200 DCA Trademark Notices Table of Contents Configuring the A164MODE Table Configuring the A164DTBL Configuration Table BECCO2200 DCA List of Figures Viii List of Tables BECCO2200 DCA About this Guide Purpose of this GuideWho Should Use this Guide Additional Documentation Introduction to the Wesdac D20 RTU GEN-0003 How this Guide is Organized Xiv Overview Xvi Configuration Tables BECO2200 DCA Configuration Tables Configuration Sequence Configuring Win for the BECO2200 DCA Wesdac Point Allocation Counters Binary InputsBinary Outputs Analog Inputs Configuring the A164APPL Table General InformationDescription of Fields DCA Index Reply Buffer Size AdjustmentSOE Buffer Size Adjustment SOE Buffer Overflow Option Device Event Response Time BECCO2200 DCA Configuring the A164PORT Table BECO2200 DCA A164PORT Configuration Table Baud Rate Communication Port NameCommunication Port Parity RTS On Time Intercharacter Timeout Remote Reply TimeoutRTS Off Time Failures Before Off-line Line Idle TimeRetries Before Failure Number of Devices on Port Configuring the A164UNIT Table BECO2200 DCA A164UNIT Configuration Table Remote Address Unit TypeType 0 Read Interval Type 3 Read Interval Type 1 Read IntervalType 2 Read Interval Type 4 Read Interval Type 7 Read Interval Type 8 Read IntervalTime Synchronization Interval Configuring the A164MODE Table First Dvcf A164MODE Number of Dvcf BECCO2200 DCA Configuring the A164DVCF Configuration Table First Data Record First UnitNumber of Units Number of Data Records Configuring the A164DTBL Configuration Table Table Type Point NumberData Value Fatal Error Messages Appendix AMessages Logged by the BECO2200 DCA F102 Bad A164UNIT record counts, must be F100 Bad A164APPL record counts, must beF101 Bad A164PORT record counts, must be F103 Bad Cfgdca record counts, must be F107 x WESDACy pnts configured, z required F105 Invalid SOE Overflow parameterF106 Total # devices exceeds Unit size F109 Cannot find x database table F108 x table creation errorF110 Fatal errors exist in configuration F111 Bad A164DVCF record counts, must be F122 Dvcf Record x, invalid First Unit F120 Mode Record x, invalid First DvcfF121 Mode Record x, invalid Number of Dvcf F123 Dvcf Record x, invalid Number of Units F203 Error x creating A164-y-z exchange F200 Error x on win openF201 Error x signaling A164-D-00 process F125 Dvcf Record x, invalid Number of Type-Point F206 Process A164-x-y died while initializing F204 Error x spawning A164-y-z processF205 Error x activating A164-y-z process F207 Unable to allocate buffers E301 Port rec x, invalid failures before offline Non-Fatal Error MessagesE300 Port rec x, invalid baud rate E302 Port rec x, num of devices exceeds Unit E304 Port rec x, invalid unit address E303 Port rec x, configuration badE307 Unit rec x, configuration bad E305 Unit rec x, invalid unit type E401 Error x setting character port E399 Non-fatal errors exist in configurationE400 Error x opening port y E308 Port rec x, num of devices cannot = E404 Error x spawning A164-y-z process E402 Error x setting SIO timersE403 Error x creating A164-y-z exchange E405 Error x activating A164-y-z process E406 Process A164-x-y died while initializing E407 Error x signalling A164-y-z processE409 Error x, invalid start signal from Spawner E408 Unable to allocate polling list PSOS Interface Warnings I701 Port rec x, invalid RTS on time Information MessagesI700 Port rec x, invalid reply time-out I702 Port rec x, invalid RTS off time I703 Port rec x, invalid intercharacter timeout I704 No Configuration deletingI705 Port rec x, no polling required Do Operate Failed Output Request Return CodesDemand Scan Failed AO Operate Failed Glossary of Terms Ascii RAM Menu-oriented software program that operates on a personal A164-0CG-1.00-2Restricted List of Acronyms and Abbreviations