GE JGBP31GEP, JGBP38GES, JGBP35GEP, JGBP34GEP After a Clean Cycle, How to Delay Start of Cleaning

After a Clean Cycle

When the clean cycle is finished, the word “CLEAN” will go out in the display and the oven will begin to cool. When the oven temperature has fallen below the locking temperature the word “LOCK” goes out and the door can be opened.

How to Delay Start of Cleaning

Delay Start is setting the oven timer to start the clean cycle automatically at a later time than the present time of day. NOTE: Before beginning, make sure the oven clock shows the correct time of day.

Quick Reminder—Delay Start for Self-Clean:

1.Prepare the oven for cleaning.

2.Close and latch the oven door.

3.Press the CLEAN pad.

4.Press the INCREASE pad. If you wish to change preset clean time of 4 hours, press the INCREASE/DECREASE pad until desired time appears.

5.Press the STOP TIME pad.

Time that appears is 4 hours later than the time of day. Press the INCREASE pad until the Stop Time you desire appears in the display. The self-clean cycle will automatically begin 4 hours before the Stop Time you select.

For example: Let’s say it’s 7:00 and you want the

oven to begin self-cleaning at 9:00 after you’re finished in the kitchen. The oven has been preset to clean for four hours.

1.Prepare the oven for cleaning.

2.Close the oven door and slide the latch handle to the right as far as it will go. Make sure the oven light is o~. Never force the fioor latch handle. Forc;ng the handle may damage the door lock mechanism.

After a clean cycle, you may notice some white ash in the oven. Just wipe it up with a damp cloth. If white spots remain, remove them with a soap-filled steel wool pad. Be sure to rinse thoroughly with a vinegar and water mixture. These deposits are usually a sdt residue that cannot be removed by the clean cycle.

If the oven is not clean after one clean cycle, the cycle may be repeated.

5.Clean Time is preset for 4 hours. You can change the Clean Time to &ywhere between 2 and 4 hours, depending on how dirty the oven is. If a shorter Clean Time is desired, press the DECREASE pad until the desired Clean Time is displayed.

6.Press the STOP TIME pad. “11:00”

STOP	appears on display and “STOP
	TIME” flashes. The control
TIME
	automatically sets Stop Time by
	adding the Clean Time to the time of
	day. In this example, the time of day
	is 7:00 and the Clean Time is 4 hours.
	Adding 4 hours to the time of day
	equals 11:00.

7.Change the Stop Time from 11:00 to 1:00 by pressing the INCREASE pad until”1 :00” appears

in the display. The words “DELAY CLEAN7’ will also appear in the display.

The self-clean cycle will automatically begin at 9:00 and finish at 1:00. The word “ON” will appear on the display at 9:00.

When the oven locks, the word “LOCK” will be displayed and a short time later, the door latch handle will be locked in position. It will not be possible to open the oven door until the temperature drops below the lock temperature.

When the clean cycle is finished, the word “CLEAN” will go out in the display and the oven will begin to cool. When the oven temperature has fallen below

the locking temperature the word “LOCK” goes out and the door can be opened.

CLEAN

n

nA

~

3.Press the CLEAN pad.

4.Press the INCREASE pad. The oven is set.

8.When the LOCK light is off, slide the latch handle to the left as far as it will go and open the door.

Never force the latch handle. Wait until the word “LOCK” goes out in the display. Forcing the latch handle may damage the door lock.

(continued next page)

23