It-Off Oven Door

The oven door is

 

 

 

removable, but it is

 

~4

heavy.

You may need

help .

 

removing and replacing

 

 

\

the door. Do not lift the ‘ ,\\

 

door by the handle. This

 

 

 

can cause the glass to

%

break or can cause

 

.

~

danla&e to the door.

 

~~

To remove the door,

 

 

 

 

open it a few inches to the special stop position that will hold the door open. Grasp firmly on each side and lift the door straight up and off the hinges. NOTE:

●Be careful not to place hands between the hinge and the oven door frame as the hinge could snap back and pinch fingers.

●While working in the oven area, cover the hinges with towels or empty paper towel rolls to prevent pinched fingers and chipping the porcelain enamel on the frame.

To replace the door, make sure the hinges are in the special stop position, Position the slots in the bottom ~.~f the Cioor sqllarely over the hinges. Then lower the lr slowly and evenly over both hinges at the same

..,,le. [f hin&es snap back against the oven frame, pull them back out.

y;,,,..,-...,,,.,

M

TO CLEAN THE DOOR:

Inside of the door:

●Because the area inside the gasket is cleaned during the self clean cycle, you do not need to clean this by hand. Any soap left on the liner causes additional stains when the oven is heated.

*The area outside the gasket can be cleaned with a scouring pad.

●Do not rub or clean the door gasket—the fiberglass material of the gasket has an extremely low resistance to abrasion. An intact and well-fitting oven door gasket is essential for energy-efficient oven operation and good baking results. If you notice the gasket becoming worn, frayed or damaged in any way or if it has become displaced on the door, you should have it replaced.

NOTE: The gasket is designed with a gap at the bottom to allow for proper air circulation.

/

I‘w’’’-’-’’”--“”’’’:4[ I I

Outside of the door:

●Use soap and water to thoroughly clean the top, sides and front of the oven door. DO NOT let water run down through openings in the top of the door. Rinse well. You may also use a glass cleaner to clean the glass on the outside of the door.

●Spillage of marinades, fruit juices, tomato sauces and basting materials containing acids may cause discoloration and should be wiped up immediately. When surface is cool, clean and rinse.

●Do not use oven cleaners, cleansing powders or harsh abrasives on the outside of the door.

(continued next IILILqe)

35

Page 34 Page 36
Page 35
Image 35
GE 164D2966P087, JTP54, JTP55 It-Off Oven Door, Oven door is Removable, but it is, To remove the door, Inside of the door
Page 34 Page 36

164D2966P087, JTP55, JTP54 specifications

The GE JTP54 and JTP55 series, with associated part number 164D2966P087, are notable offerings in the realm of jet engine technology, specifically designed for use in various commercial aircraft. These engines exhibit a combination of advanced engineering and reliable performance, making them a popular choice among aircraft manufacturers.

One of the key features of the JTP54 and JTP55 engines is their high-bypass turbofan design, which promotes fuel efficiency while delivering optimal thrust. This turbofan architecture allows for a greater percentage of airflow to bypass the combustion engine core, resulting in reduced fuel consumption and lower emissions. The engines are well-suited for long-haul flights, where fuel efficiency is critical to operating costs.

The JTP54 and JTP55 models leverage a range of advanced materials and technologies to enhance durability and performance. The compressor sections utilize composite fan blades made from lightweight materials, which contribute to improved aerodynamic efficiency. High-temperature super alloys in the turbine sections provide superior resistance to thermal fatigue, allowing the engine to operate effectively under high-stress conditions.

Another notable characteristic of the JTP54 and JTP55 engines is their noise reduction technologies. The application of chevrons on the engine nacelles and the use of advanced acoustic liners minimize the noise generated during operation, making these engines compliant with stringent noise regulations set by aviation authorities. This focus on quiet operation enhances passenger comfort, especially on short-range flights and takeoffs or landings in urban areas.

Connectivity and diagnostic capabilities are also integral to the JTP series. Integrated health management systems monitor engine performance in real time, enabling predictive maintenance strategies that can significantly reduce downtime. This technology allows operators to anticipate potential issues before they become critical, ensuring flight safety and enhancing overall operational efficiency.

In conclusion, the GE JTP54, JTP55, and 164D2966P087 engines epitomize advanced aerospace engineering with their high-bypass turbofan design, utilization of cutting-edge materials, emphasis on noise reduction, and incorporation of smart technologies. These features not only improve operational performance and fuel efficiency but also contribute to a more sustainable and comfortable flying experience. For airlines and operators, choosing the JTP series means investing in a technology that aligns with modern aviation demands for safety, performance, and environmental responsibility.
Top Page Image Contents