C- Ck

3 ,,ti clock must be set for the automatic oven timing functions to work properly. The time of day cannot be changed during a Timed Bake or CLEAN cycle.

To Set the Clock

 

1. Press the

 

2. Press the

CLOCK

CLOCK pad.

 

INCREASE or

 

 

DECREASE pad

A

 

@

to set the time

 

A of day.

❑

 

3. Press the CLOCK pad to start.

Timer

The [imer is a minute timer; it does not control oven operations. The maximum setting on the timer is 9 hours and 55 minutes.

To Set the Timer

1.Press the TIMER

❑TIMER ON/OFF pad.

ON/OFF A

2.Press the INCREASE or DECREASE pad to set the amount of time on the timer.

The timer will start automatically within a few seconds of releasing the INCREASE or DECREASE pad

The timer, as you are setting it, will display hours and minutes “HR” will be in the display.

During the countdown, when the timer reaches the last minute, the display will change to seconds only and a single beep will sound.

r Reset the Timer

11 TIMER” is displayed, press the INCREASE or DECREASE pad until desired time is reached.

If “TIMER” is not displayed, press the TIMER ON/OFF pad first, then follow the instructions above to set the timer.

End of Cycle Tone

To Cancel the Timer

Press and hold the TIMER ON/OFF pad until the word “TIMER” disappears from the display.

The End of Cycle tone is a series of 3 beeps followed by 1 beep every 6 seconds. If you would like to remove the signal that beeps every 6 seconds, press and hold the CLEAR/OFF pad for 1() seconds.

To return the signal that beeps every 6 seconds, press and hold the CLEAWOFF pad for 10 seconds.

Power Outage

After a power outage, when power is restored, the display will flash and time shown will no longer be correct—for example, after a 5-minute power interruption the clock will be 5 minutes slow.

All other functions that were in operation when the power went out will have to be programmed again.

((c)lltill[(c,{l jle.rt /ILIg<,)

Page 6 Page 8
Page 7
Image 7
GE JTP55 To Set the Clock, To Set the Timer, Reset the Timer, End of Cycle Tone To Cancel the Timer, Power Outage
Page 6 Page 8

164D2966P087, JTP55, JTP54 specifications

The GE JTP54 and JTP55 series, with associated part number 164D2966P087, are notable offerings in the realm of jet engine technology, specifically designed for use in various commercial aircraft. These engines exhibit a combination of advanced engineering and reliable performance, making them a popular choice among aircraft manufacturers.

One of the key features of the JTP54 and JTP55 engines is their high-bypass turbofan design, which promotes fuel efficiency while delivering optimal thrust. This turbofan architecture allows for a greater percentage of airflow to bypass the combustion engine core, resulting in reduced fuel consumption and lower emissions. The engines are well-suited for long-haul flights, where fuel efficiency is critical to operating costs.

The JTP54 and JTP55 models leverage a range of advanced materials and technologies to enhance durability and performance. The compressor sections utilize composite fan blades made from lightweight materials, which contribute to improved aerodynamic efficiency. High-temperature super alloys in the turbine sections provide superior resistance to thermal fatigue, allowing the engine to operate effectively under high-stress conditions.

Another notable characteristic of the JTP54 and JTP55 engines is their noise reduction technologies. The application of chevrons on the engine nacelles and the use of advanced acoustic liners minimize the noise generated during operation, making these engines compliant with stringent noise regulations set by aviation authorities. This focus on quiet operation enhances passenger comfort, especially on short-range flights and takeoffs or landings in urban areas.

Connectivity and diagnostic capabilities are also integral to the JTP series. Integrated health management systems monitor engine performance in real time, enabling predictive maintenance strategies that can significantly reduce downtime. This technology allows operators to anticipate potential issues before they become critical, ensuring flight safety and enhancing overall operational efficiency.

In conclusion, the GE JTP54, JTP55, and 164D2966P087 engines epitomize advanced aerospace engineering with their high-bypass turbofan design, utilization of cutting-edge materials, emphasis on noise reduction, and incorporation of smart technologies. These features not only improve operational performance and fuel efficiency but also contribute to a more sustainable and comfortable flying experience. For airlines and operators, choosing the JTP series means investing in a technology that aligns with modern aviation demands for safety, performance, and environmental responsibility.
Top Page Image Contents