www.GEAppliances.com

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

Safety Instructions

WARNING—To reduce the risk of burns, electric shock, fire, injury to persons or exposure to excessive microwave energy:

■Use this appliance only for its intended use as described in this manual. Do not use corrosive chemicals or vapors in this appliance. This cooking center is specifically designed to heat or cook food, and is not intended for laboratory or industrial use.

■Be sure your appliance is properly installed and grounded by a qualified technician in accordance with the provided Installation Instructions.

■Have the installer show you the location of the circuit breaker or fuse. Mark it for easy reference.

■Be sure the cooking center is securely installed in a cabinet that is firmly attached to the house structure. Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit, or hang on the oven door.

■This appliance must be connected to a grounded, metallic, permanent wiring system, or an equipment grounding conductor should be run with the circuit conductors and connected to the equipment grounding terminal or lead on the appliance.

■This appliance should be serviced only by qualified service personnel. Contact nearest authorized service facility for examination, repair or adjustment. Do not repair or replace any part of this appliance unless specifically recommended in this manual. All other servicing should be referred to a qualified technician.

■Do not store this appliance outdoors. Do not use this product near water—for example, in a wet basement, or near a swimming pool.

■Before performing any service, disconnect the cooking center power supply at the household distribution panel by removing the fuse or switching off the circuit breaker.

■Do not operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been damaged or dropped.

■Do not leave children alone—children should not be left alone or unattended in an area where appliance is in use. They should never be allowed to sit or stand on any part of the appliance.

■Don’t allow anyone to climb, stand or hang on the door. They could damage the cooking center and cause severe personal injury.

■CAUTION: Items of interest to children should not be stored in cabinets above an oven; children climbing on the oven to reach items could be seriously injured.

■Teach children not to play with the controls or any other part of the cooking center.

■Large scratches or impacts to glass door can lead to broken or shattered glass.

■Wear proper clothing. Loose-fitting or hanging garments should never be worn while using the appliance. Flammable material could be ignited if brought in contact with hot heating elements and may cause severe burns.

3

Operating Instructions Care and Cleaning Troubleshooting Tips Consumer Support

Page 2 Page 4
Page 3
Image 3
GE JTP95 owner manual Safety Precautions, Safety Instructions
Page 2 Page 4

JTP95 specifications

The GE JTP95 is a notable entry in General Electric's line of high-performance jet engines, designed primarily for commercial aviation applications. Known for its advanced technological features, the JTP95 integrates innovative design elements that enhance efficiency, performance, and reliability while minimizing environmental impact.

At the heart of the JTP95 engine is its turbofan configuration, which combines superior thrust capabilities with reduced noise levels. This design not only provides the necessary power for larger aircraft but also adheres to increasingly stringent noise regulations, making it a favorite among carriers operating in noise-sensitive areas.

One of the standout features of the GE JTP95 is its advanced materials technology. The engine incorporates lightweight composite materials and high-strength alloys, which contribute to fuel efficiency while ensuring durability under stress. These materials allow for higher operating temperatures, leading to improved thermal efficiency and overall performance.

The engine utilizes an innovative full authority digital engine control (FADEC) system, which optimizes fuel consumption and engine performance in real-time. This system ensures that the engine operates at peak efficiency throughout various flight conditions, providing pilots with valuable performance data and enhancing safety measures.

Moreover, the JTP95 is designed with a bypass ratio that significantly reduces emissions when compared to older engine models. The high bypass ratio means that a larger proportion of air is directed around the engine core, which not only improves fuel efficiency but also results in lower carbon emissions, aligning with the industry's shift towards more sustainable aviation solutions.

Maintenance is another area where the GE JTP95 excels. The engine features modular design components, allowing for easier access to critical parts during servicing. This reduces downtime and associated costs for airlines, while also enhancing the overall reliability of the engine over its lifespan.

In summary, the GE JTP95 stands out in the aviation sector for its combination of innovative technologies, advanced materials, and efficient design. It exemplifies GE's commitment to developing engines that meet modern demands for performance, reliability, and environmental stewardship, making it a key player in the future of commercial aviation. Organizations looking for a high-performance and environmentally friendly solution for their fleet will find the JTP95 to be an ideal choice.
Top Page Image Contents