QS-25 | GE QS24 UR guide

QUICKSTART GUIDE

ZReboot the switch using the Reboot command as shown.

Note when asked to save the current configuration enter Y for Yes.

ZOnce the Switch has rebooted, you will need to login again.

ZTo confirm that the IP address and subnet mask were saved correctly enter the command “show setup” followed by the Enter key.

The Switch will then provide an on-screen list of the switch’s settings including the switch’s IP address and subnet mask, and, if programmed, the default gateway.

Once you have verified that the IP, subnet mask and default gateway settings are correct you can configure the Switch via the web interface.

ZIf the computer is already on a network, connect the Switch to the network.

The next step is to test communications to the switch with the ping command:

ZFrom the command prompt type in PING 3.94.247.229.

ZPress the Enter key.

If communication is working correctly you should get a response from the Switch. If there is a problem you will get four consecutive timeout error messages. If this occurs check the media, ensure that the IP address subnet mask has been set correctly, and try again.

UR SWITCH MODULE – QUICKSTART GUIDE

QS–25

Image 29

GE QS24 UR quick start QS-25

Contents

GE Multilin UR Switch Module Ethernet Communications GE Multilin Incorporated. All rights reserved Table of Contents Table of Contents TOC-2 QS-1 Fiber Twisted Pair copper cable Star Architecture QS.1.2 Supported Network TopologiesMesh Architecture Ring Architecture Ethernet Unshielded Twisted Pair Unshielded Twisted Pair cable QS-5 QS-6 Wavelengths of light QS.3.1 Fiber Optic Ethernet Multi Mode Fiber Cable Cross Section and Physical SpecificationsSingle Mode QS.3.2 Single and Multi-mode cable Difference between Single-mode and Multi-mode Cable QS.3.3 Optical Power Budget Figure QS-4 Common Fiber Optic Connectors QS.3.4 Maximum fiber segment length calculation Maximum 10 Mbps Ethernet Segment Lengths QS.3.5 UR-2S and UR-2T 10/100 BaseT Switch Ports QS.4 Introduction to the 2S and 2T UR Managed Switch Modules Figure QS-5 Traditional Redundant UR LAN Topology QS.4.1 Hardware Overview QS.4.2 2S and 2T LED indicators T60 Transformer Management Relay QS.4.3 Hardware Installation AC or DC QS.4.4 initial Configuration Procedure QS-18 DB9 Female to DB9 Female Cable Pin-out QS-20 QS-21 QS-22 QS-23 Type in ipconfig ip= QS-25 Select Properties QS.4.7 Assigning a static IP Address to a personnel computer Right mouse click on the Local Area Connections icon Select Use the following IP address Addresses now being used QS-30 Function Module Offline QS.4.8 Self-test Errors and Meaning Equipment Background QS.5 Tagged VLAN’s Configuring a Vlan within the Switch QS.5.1 Configuring Tagged VLANs Save We have now configured the Switch to support Tag-based VLANs QS-37 Configure You have now completed the exercise Figure QS-15 Configuration of UR Switch Ring-only Mode QS.5.2 Configuring the UR Switch for Ring Only Mode QS-41 Select Bridge Rstp Then Save Enable Status Once saved, select OK, then OK again to exit Select the Configuration Rstp RO Mode menu as shown above Then Save Enable status For Every Switch RING, Disable LLA on Ports That are Ring Figure QS-16 Configuration of the UR Switch Ring-only mode You have completed configuration of Ring-only mode Saving Switch Settings QS.5.3 Saving and Loading Switch SettingsLoading Switch Settings Select the Retrieve Switch Settings Files option QS-50 Version 2.1beta QS.6.1 Updating UR Switch Module FirmwareQS.6.2 Selecting the Proper Version QS-52 QS-53 QS-54