 General Hazards, Electrical Hazards, Danger | Generac 005031-2

Image 4

Generac 005031-2 owner manual  General Hazards, Electrical Hazards, Warning , Danger

Contents

SHOULD ATTEMPT INSTALLATION Liquid-cooled,Prepackaged Standby GeneratorsModel Number 005031-225kW This manual should remain with the unit AUTHORIZED SERVICE DEALER LOCATION ‹OPERATION AND MAINTENANCE‹HOW TO OBTAIN SERVICE INTRODUCTION INTRODUCTION ELECTRICAL HAZARDS  GENERAL HAZARDSWARNING   EXPLOSION HAZARDS FIRE HAZARDS‹STANDARDS INDEX 1.2TRANSFER SWITCH 1.1GENERATOR1.3ATS MODE AUTOMATIC OPERATION 1.4GENERATOR AC CONNECTION SYSTEMS ‹1.7.1 LOW OIL PRESSURE SWITCH ‹1.7.2 HIGH COOLANT TEMPERATURE SWITCH‹1.7.3 LOW COOLANT LEVEL SWITCH Figure 1.4 - Low Oil Pressure Switch 1.10 SPECIFICATIONS ‹1.7.6 LOW BATTERY‹1.8.1 UNPACKING PRECAUTIONS 1.8UNPACKING 1.12RECONFIGURING THE FUEL SYSTEM FOR LP VAPOR Figure 1.8 - Reconfigure the Fuel System1.11 FUEL CONSUMPTION 1.13 ENGINE OIL RECOMMENDATIONS 2.1STANDBY GENERATOR INSTALLATION 1.15 BEFORE INSTALLATION1.14 COOLANT RECOMMENDATIONS ‹2.1.1 NFPA STANDARDS 2.2GENERATOR LOCATION 2.3GENERATOR MOUNTING AND SUPPORT2.4BASIC STANDBY ELECTRIC SYSTEM ‹2.1.2 OTHER PUBLISHED STANDARDS 2.9USING A “GTS” TRANSFER SWITCH 2.5EMERGENCY CIRCUIT ISOLATION METHOD2.6TOTAL CIRCUIT ISOLATION METHOD 2.7GROUNDING THE GENERATOR Pos2 OFF — ATS Application 2.10 BATTERY INSTALLATION‹2.10.1 VENTED BATTERIES 3.1GTS TRANSFER SWITCH ‹2.11.2 TRANSFER SWITCH2.11 PREPARATION BEFORE START-UP ‹2.11.4 GENERATOR SET LUBRICATION ‹3.2.1 AUTO/OFF/MANUAL SWITCH ‹3.2.2 FAULT INDICATOR LEDS3.2CONTROL CONSOLE COMPONENTS GTS Mode Operation ‹3.2.5 SET EXERCISE TIME SWITCH ‹3.2.3 15 AMP FUSE‹3.2.4 5 AMP FUSE ‹3.2.6 SYSTEM READY LED 3.4ENGINE GOVERNOR GAIN ADJUSTMENTS 3.3MANUAL TRANSFER AND START-UP3.5MANUAL RETRANSFER AND SHUTDOWN Figure 3.2 - Engine Governor Adjustment 3.8CONTROL BOARD DIP SWITCH SETTINGS Figure 3.3 - “Set Exercise Time” Switch3.6AUTOMATIC OPERATION 3.7WEEKLY EXERCISE CYCLE 3.9VOLTAGE REGULATOR ADJUSTMENT ‹EVERY THREE MONTHS‹ONCE EVERY SIX MONTHS ‹ONCE ANNUALLY 4.2EXHAUST MANIFOLD PROCEDURE 4.3INTAKE MANIFOLD PROCEDURE4.4CYLINDER HEAD PROCEDURE Figure 4.1 - Intake Manifold Installation 4.8MAINTENANCE OWNER/ OPERATOR CAN PERFORM ‹4.7.2 BATTERY FLUID‹4.8.2 CHECK BATTERY 4.6OVERLOAD PROTECTION FOR ‹4.8.11 CHANGING THE ENGINE AIR CLEANER Figure 4.4 - Setting the Spark Plug Gap‹4.8.7 INSPECT EXHAUST SYSTEM ‹4.8.8 CHECK FAN BELT 4.9MISCELLANEOUS MAINTENANCE ‹4.9.1 CLEANING THE GENERATOR‹4.9.2 BATTERY ‹4.9.3 BATTERY MAINTENANCE 4.10 SCHEDULED MAINTENANCE Service Maintenance Interval Information Tasks Level TROUBLESHOOTING POINTS PROBLEMCAUSE CORRECTION Section 6 - Electrical Data Section 6 - Electrical Data Section 6 - Electrical Data Liquid-cooled25 kW Generators Section 6 - Electrical Data Section 6 - Electrical Data Liquid-cooled25 kW Generators Section 6 - Electrical Data Section 6 - Electrical Data Liquid-cooled25 kW Generators Section 6 - Electrical Data Section 7 - Exploded Views and Parts Lists DESCRIPTION Mounting Base - Drawing No. 0F0104-B 38 3 45 39 32 18 LATCH DETAIL Enclosure - Drawing No. 0F1645-H Section 7 - Exploded Views and Parts Lists 0F0790 Control Panel 25kW - Drawing No. 0E7615-C Section 7 - Exploded Views and Parts Lists FOR HARNESS GROUND STEPPERONLY RADIATOR Engine - Drawing No. 0E9918-F COVER Fuel System - Drawing No. 0E9980-D LOCKTIGHT LEADS 0F1659A Muffler - Drawing No. 0F2930-C Stepper Motor - Drawing No. 0E9979-C TO THERMOSTAT Radiator - Drawing No. 0E9965-FADAPTER Section 8 - Installation Diagram PURCHASER’S/OWNER’S WARRANTY RESPONSIBILITIES YOUR WARRANTY RIGHTS AND OBLIGATIONSCALIFORNIA EMISSION CONTROL WARRANTY STATEMENT EMISSION CONTROL SYSTEM WARRANTY EMISSION RELATED PARTS INCLUDE THE FOLLOWING WARRANTY SCHEDULE THIS WARRANTY SHALL NOT APPLY TO THE FOLLOWING