English
10" Table Saw
Operator’s Manual GTS10S
APPLiCATiOnS
Cutting Tips:
1. Makesurethekerfismadeonthescrapsideofthemeasuringline.
2. Cutthewoodwiththenishsideup
3. Alwayshaveapropersupportforthewoodasitcomesoutoftheblade.
4. Makeatestcutforimportantcuts
5. Alwaysusethecorrectbladedepthsetting.TheTopofthebladeteethshouldcleartheworkpieceby1/8”(3mm)to¼”(6mm)
6. Inspecttheworkpieceforknotsornailsbeforebeginningacut.Removeanylooseknotsornailswithahammer
7. Alwaysuseclean,sharp,properly-setblades,Nevermakeacutwithdullblade
8. Whenmakingacut,usesteady,evenpressure,Neverforceacut
9. DoNOTcutwetorwarpedlumber
10.Alwaysholdyourworkpiecermlywithbothhandsorusepushstickorpushblock.
Cross Cutting:
WArning:Make sure the blade guard assembly is properly installed to avoid serious personal injury
1. Removetheripfencefromthetablesurface
2. PositionMiterGaugeto0°
3. Makesureallloosepieceshavebeenremovedfromthetablesurfaceandworkpieceisnotincontactwithblade
4. TurnON/OFFswitchtotheONposition
5. Positiontheworkpieceatonthetablewithedgeushagainstmitergaugefence.Waituntilbladereachesfullspeedbeforefeedingthework
pieceintotheblade
6. usetwohandstoslowlyfeedtheworkpieceandmitergaugetowardtheblade.usethehandfurthestfromthebladetokeeptheworkpieceush
againstmitergaugefenceanduseyourotherhandtopushthemitergaugeandworkpiecetowardtheblade.Standslightlytothesideofthe
bladetoreducetheriskofinjuryshouldkickbackoccur.
7. Continuefeedingtheworkpieceintothebladeuntilthecuthasbeencompleted.
8. Oncethecuthasbeencompleted,pulltheworkpiecebacktowardyou
9. Turntheswitchoff
10.Afterbladehasstoppedcompletely,removethecutoffpiece.
Rip Cutting:
WArning:Make sure the blade guard assembly is properly installed to avoid serious personal injury.
1. RemovetheMiterGaugefromthetable
2. Placetheripfenceonthedesireddistancefromtheblade.Remembertoallowforthekerf.
3. Makesurealllooseitemshavebeenremovedfromthetableandthatworkpieceisnotcontactwiththeblade
4. Ifworkpieceislargerthan36”long,placeasupportwiththesameheightastablebehindthesawforthecutwork
5. TurnON/OFFswitchtoONposition
6. Positiontheworkpieceatonthetablewithedgeushagainstripfence.Waituntilbladereachesfullspeedbeforefeedingtheworkpieceintothe
blade
7. Standslightlytothesideofbladetoreducetheriskofinjurycausedshouldkickbackoccur..usingapushstickorpushblock,slowlyfeedthework
piecetowardtheblade.
8. Oncetheworkpiecehasmadecontactwiththeblade,usehandclosesttotheripfencetoguideit.Makesuretheedgeoftheworkpiecekeepsin
solidcontactwiththeripfenceandtablesurface.Ifrippingapiecenarrowerthan4”,useapushsticktomovethepiecethroughthecut.
9. Continuefeedingtheworkpieceintothebladeuntilthecuthasbeencompleted.
10.Oncethecuthasbeencompleted,grasptheworkpiecefromtheleadendandpullitoffthetablesurface.
11.Turntheswitchoff
12.Afterbladehasstoppedcompletely,removethecutoffpiece
WArning:To avoid serious personal injury, never push a small piece of wood into the blade with your hand.
Always use a push stick or push block.