![SECT 9—PROGRAMMING REMOTE CONTROLS FOR HELP-GENIECOMPANY.COM](/images/new-backgrounds/184655/18465557x1.webp)
SECT 9—PROGRAMMING REMOTE CONTROLS FOR HELP-GENIECOMPANY.COM
PROGRAMMING REMOTE CONTROLS |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |
NOTE: Each remote device must be |
|
| Learn Button |
|
|
|
| |||
programmed separately |
|
|
|
|
|
|
| 29 | ||
|
|
|
|
|
|
|
|
|
| |
|
| WARNING |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |
Moving door can cause serious injury or death. |
|
|
|
|
|
|
|
| ||
| • Keep people clear of opening while door |
|
|
|
| Learn Indicator |
|
| ||
|
|
|
|
|
|
|
|
| ||
| is moving. |
|
|
|
|
|
|
|
| |
| • Do not allow children to play with |
|
|
|
|
|
|
|
| |
| remote controls. |
|
|
|
|
|
|
|
| |
If Safety reverse does not work properly: |
|
|
|
|
|
|
|
| ||
| • Close door and disconnect operator using |
|
|
|
|
|
|
|
| |
| emergency release. |
|
|
|
|
|
|
|
| |
| • Do not use door operator, remote controls, |
|
|
|
|
|
|
|
| |
| or wireless keypad. |
|
|
|
|
|
|
|
| |
|
| Fig. | ||||||||
| • Refer to door and door operator owner’s |
| ||||||||
|
|
|
|
|
|
|
|
| ||
| manuals before attempting any repairs. |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| ||
NOTE: Remote controls will not close door if |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| |||
|
| To erase all receiver memory, such as |
|
| ||||||
NOTE: When programming remote control, it must |
|
| ||||||||
| following loss of remote, home sale or |
|
| |||||||
be at least 24 inches from the antenna. |
|
| ||||||||
| tenant |
|
| |||||||
1. Program one button remote. |
|
| ||||||||
| • Press and hold learn code button for |
|
| |||||||
| • | Lower lens cover. |
|
| ||||||
|
| 10 seconds or until learn code |
|
| ||||||
| • Locate learn code button and learn indicator on |
|
| |||||||
|
| indicator goes |
|
| ||||||
|
| power head Fig. |
|
| ||||||
|
|
| • Program remotes as before. |
|
| |||||
| • Press and release learn code button. |
|
| |||||||
|
| – Red learn indicator blinks 2 times per second. |
|
|
|
|
|
|
|
|
| • Press remote control button once within |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| ||
|
| 30 seconds. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| – Red learn indicator stays lit. |
| FCC and IC CERTIFIED |
|
| ||||
| • Press remote control button again. |
|
| |||||||
|
| This device complies with FCC Part 15 and RSS |
| |||||||
|
| – Red indicator goes out and memory |
| 210 of Industry Canada. This equipment has been |
| |||||
|
| is stored. |
| tested and found to comply with the limits for a |
| |||||
NOTE: If red indicator blinks approximately 4 |
| Class B digital device, pursuant to Part 15 of the |
| |||||||
| FCC Rules. These limits are designed to provide |
|
| |||||||
times per second, programming has stopped. |
|
| ||||||||
| reasonable protection against harmful interference |
| ||||||||
If programming stops, repeat above steps. |
| in a residential installation. This equipment |
| |||||||
2. | Program |
| generates, uses and can radiate radio frequency |
| ||||||
| • Repeat step 1 above “Program |
| energy and, if not installed and used in accordance |
| ||||||
|
| with the instructions, may cause harmful |
|
| ||||||
|
| remote” for each button and operator. |
|
| ||||||
|
|
| interference to radio communications. However, |
|
| |||||
NOTE: Each button on a |
|
| ||||||||
| there is no guarantee that interference will not |
| ||||||||
control is for a different operator. You cannot use |
| occur in a particular installation. If this equipment |
| |||||||
more than one button on a |
| does cause harmful interference to radio or |
| |||||||
| television reception, which can be determined by |
|
| |||||||
a single door. |
|
| ||||||||
| turning the equipment off and on, the user is |
|
| |||||||
3. | Operating remote. |
|
| |||||||
| encouraged to try to correct the interference by one |
| ||||||||
| • | Press button once: |
| or more of the following measures: |
| |||||
|
| – If door is at up or down limit, door will move |
| • |
| |||||
|
|
| • Increase the separation between the operator |
|
| |||||
|
| away from that limit. |
|
| ||||||
|
|
| and receiver. |
|
| |||||
|
| – If door is stopped between limits, it will move |
|
| ||||||
|
|
| • Connect the operator into an outlet on a circuit |
| ||||||
|
| toward the limit where it was last stopped. |
| different from that to which the appliance |
| |||||
|
| – If door is moving, it will stop. |
| is connected. |
| |||||
NOTE: Door automatically stops at end of open or |
| • Consult the dealer. |
| |||||||
|
|
|
|
|
|
|
| |||
close cycle. |
|
|
|
|
|
|
|
|