Goodman Mfg GCVC9/GMVC95 Furnace Specifications, GCVC90704CX, GCVC90905DX, GCVC91155DX

FURNACE SPECIFICATIONS				GCVC9
	MODEL	GCVC90704CX*	GCVC90905DX*	GCVC91155DX*
	Btuh Input (US) High Fire	69,000	92,000	115,000
	Output (US) High Fire	65,300	86,500	109,000
	Btuh Input (US) Low Fire	48,000	64,000	80,000
	Output (US) Low Fire	45,000	60,100	77,400
	A.F.U.E.	93.0%	92.0%	93%
	Rated External Static (" w.c.)	.10 - .50	.10 - .50	.10 - .50
	Temperature Rise (°F)	30 - 60	30 - 60	40 - 70
	High Stage Pressure Switch Trip Point (" w.c.)	-0.55	-0.55	-0.55
	Low Stage Pressure Switch Trip Point (" w.c.)	-0.20	-0.20	-0.20
	Front Cover Pressure Switch Trip Point (" w.c)	-0.37	-0.37	-0.37
	Blower Wheel (D" x W")	10 x 10	11 x 10	11 x 10
	Blower Horsepower	3/4	1	1
	Blower Speeds	Refer to airflow charts in this manual.
	Max CFM @ 0.5 E.S.P.
	Power Supply	115-60-1	115-60-1	115-60-1
	Minimum Circuit Ampacity (MCA)	14.1	14.4	14.4
	Maximum Overcurrent Device	15	15	15
	Transformer (VA)	40	40	40
	Heat Anticipator (Amps)	0.7	0.7	0.7
	Primary Limit Setting (°F)	160	170	145
	Auxiliary Limit Setting (°F)	220	180	180
	Rollout Limit Setting (°F)	220	210	210
	Fan Delay On Heating	30 secs.	30 secs.	30 secs.
	Off Heating *	150 secs.	150 secs.	150 secs.
	Fan Delay On Cooling	5 secs.	5 secs.	5 secs.
	Off Cooling	45 secs.	45 secs.	45 secs.
	Fan Delay On - Fan Only	5 secs.	5 secs.	5 secs.
	Gas Supply Pressure (Natural/Propane) (" w.c.)	7 / 11	7 / 11	7 / 11
	Manifold Pressure (Natural/Propane) High Stage (" w.c.)	3.5 / 10	3.5 /10	3.5 /10
	Manifold Pressure (Natural/Propane) Low Stage ("w.c.)	1.9 / 6.0	1.9 / 6.0	1.9 / 6.0
	Orifice Size (Natural/Propane)	#43 / #55	#43 / #55	#43 / #55
	Number of Burners	3	4	5
	Vent Connector Diameter (inches)	2	2	2
	Combustion Air Connector Diameter (inches)	2	2	2
	Shipping Weight (lbs.)	157	172	175

*Off Heating - This fan delay tim ing is adjustable (90, 120, 150 or 180 seconds), 150 seconds as shipped.

1.These furnaces are manufactured for natural gas operation. Optional Kits are available for conversion to propane gas operation.

2.For elevations above 2000 ft. the rating should be reduced by 4% for each 1000 ft. above sea level. The furnace must not be derated, orifice changes should only be made if necessary for altitude.

3.The total heat loss from the structure as expressed in TOTAL BTU/HR must be calculated by the manufactures method in accordance with the "A.S.H.R.A.E. GUIDE" or "MANUAL J-LOAD CALCULATIONS" published by the AIR CONDITIONING CONTRACTORS OF AMERICA. The total heat loss calculated should be equal to or less than the heating capacity. Output based on D.O.E. test procedures, steady state efficiency times output.

4.Minimum Circuit Ampacity calculated as: (1.25 x Circulator Blower Amps) + I.D. Blower Amps.

18