|
|
|
|
|
|
|
|
|
|
|
|
| Troubleshooting | |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
TYPE OF PROBLEM | WHAT TO CHECK |
| HOW TO CHECK | |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
Sprayer does not run at all | Allow sprayer to cool. If sprayer | NOTE: Motor must be cooled down for the test. | ||||||||||||
|
|
| runs when cool, correct cause of | 1. | Check thermal device connector (yellow wires) | |||||||||
Display shows CODE 06 | ||||||||||||||
overheating. Keep sprayer in cooler | ||||||||||||||
|
|
|
| at control board. | ||||||||||
|
|
| location with good ventilation. Make |
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
| sure motor air intake is not blocked. 2. | Disconnect thermal device connector from control | ||||||||||
|
|
| If sprayer still does not run, follow |
| board socket. Make sure contacts are clean and | |||||||||
|
|
|
| |||||||||||
|
|
|
| secure. Measure resistance of the thermal device. If | ||||||||||
|
|
| Step 1. |
| ||||||||||
|
|
|
| reading is not correct, replace motor. | ||||||||||
|
|
|
|
| ||||||||||
|
|
|
|
| Check Motor Thermal Switch: Unplug thermal | |||||||||
|
|
|
|
| ||||||||||
|
|
|
|
| ||||||||||
|
|
|
|
| wires. Set meter to ohms. Meter should read the | |||||||||
|
|
|
|
| proper resistance for each unit (see table below). | |||||||||
Control board status light blinks |
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
| ||||
6 times repeatedly |
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| - |
|
|
|
| ti13140a |
|
|
|
| Resistance Table: | |
|
|
| 695/240V Mark IV | 0 ohms |
|
|
| 795/120V Mark IV | 2k ohms |
|
|
| 1095/240V Mark V | 3.9k ohms |
|
|
| 1595/120V Mark V/MARK VII | 6.2k ohms |
|
|
| MARK X | 10.0k ohms |
|
| 3. | Reconnect thermal device connector to control | |
|
|
| board socket. Connect power, turn sprayer ON and | |
|
|
| control knob 1/2 turn clockwise. If sprayer does not | |
|
|
| run, replace control board. |
|
Sprayer does not run at all | Check voltage supply to the sprayer 1. | Set sprayer to OFF and disconnect power to | ||
Display shows CODE 08 | (incoming voltage too low for |
| sprayer. |
|
sprayer operation) |
|
|
| |
| 2. | Remove other equipment that uses the same circuit. | ||
|
| |||
|
| 3. | Locate a good voltage supply to avoid damage to | |
|
|
| electronics. |
|
Control board status light blinks |
|
|
| |||
eight times repeatedly |
|
|
| |||
|
|
|
|
| ||
Sprayer does not run at all | Check to see if control board is over 1. | Make sure motor air intake is not blocked. | ||||
|
|
| heating. | 2. | Make sure fan has not failed. | |
Display shows CODE 10 | ||||||
| ||||||
|
|
|
| 3. | Make sure control board is properly connected | |
|
|
|
|
| to back plate and that conductive thermal paste | |
|
|
|
|
| is used on power components. | |
|
|
|
|
| ||
|
|
|
| 4. | Replace control board. | |
|
|
|
| 5. | Replace motor. | |
|
|
|
| |||
|
|
|
|
|
| |
Control board status light blinks |
|
|
| |||
10 times repeatedly |
|
|
|
332916C | 31 |