Model G0759 | Grizzly instruction

MODEL G0759

MILL/DRILL

w/STAND & DRO

MANUAL INSERT

The Model G0759 is the same machine as the Model G0704 except the Model G0759 has a 3-axis DRO. Besides the differences noted in this insert, all other content in the Model G0704 owner's manual applies to this machine. Before operating your new machine, you MUST read and understand this insert, the entire Model G0704 manual, and the DRO manual to reduce the risk of injury when using this machine.

If you have any further questions about this manual insert or the differences between the Model G0759 and the Model G0704, contact our Technical Support at (570) 546-9663 or email techsupport@grizzly.com.

COPYRIGHT © FEBRUARY, 2014 BY GRIZZLY INDUSTRIAL, INC., REVISED APRIL, 2014 (TS)

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

(FOR MODELS MANUFACTURED SINCE 1/14) #TS16276 PRINTED IN CHINA

Image 1

Grizzly owner manual Model G0759

Contents

Model G0759 Machine Data Sheet Table Info Column & Stand Description Electrical Box Headstock Description Chip Guard Labels Model G0704 MILL/DRILL with Stand Page Table of Contents Manual Accuracy Contact Info IntroductionMachine Description Identification G0704 electronic controls identification Electronic Controls Identification Model G0704 DRILL/MILL with Stand 50 2250 RPM Accessories Included Safety Instructions for Machinery Safety ChILdREN & BYsTANdERs. Keepchildrenand Maintain Power CORds. When disconnect Additional Safety for Mill/Drills Power Supply 50 ft Minimum Gauge Size 16 AWG Unpacking Needed for SetupDescription Qty Inventory Contents QtyNot Shown Before cleaning, gather the following CleanupBasic steps for removing rust preventative Site Considerations Weight Load Moving & Placing Machine Example of a direct mount setup Bolting to Concrete Floors Mounting to Shop Floor To install the drill chuck onto the arbor AssemblyDrill Chuck Arbor To assemble your machine Connecting Power Power Connection To test run and break-in the spindle bearings Test Run & Spindle Break-in Operation Overview Operations Speed Range Selector Knob Selects low range Basic Controls Digital readout unit controls Model G0704 Mfg. Since 08/11 To use the digital readout Digital Readout Unit To determine the needed spindle speed Calculating Spindle Speed To set the spindle speed Spindle Speed Direction Spindle Height Controls Changing Spindle Position Using Quill Feed Levers Drill Chuck To install the drill chuck and arbor Loading Tooling To install the toolingTo remove the collet To raise or lower the headstock Headstock Travel Axis and RotationTo tilt the headstock to the left or right Longitudinal Feed Table TravelCross Feed H8177-Worktable with Angle H8179G5684-R-8 Vertical Collet Rack G8683Z-Mini Shop Fox Mobile Base G9322-Boring Head Combo SetH5685-4Rotary Table G5758-Tilt x Model G9512 T-Slot Nuts Schedule MaintenanceLubrication To lubricate the leadscrews Tools Needed Qty Handwheel gears Troubleshooting Service Symptom Possible Cause Possible Solution To adjust the headstock gibs To adjust the table gibsGibs To adjust the Y-axis leadscrew nut Battery ReplacementTo adjust the X-axis leadscrew To replace the digital readout unit battery To inspect and replace the motor brushes Motor Service Wiring Safety Instructions Wiring Wiring Diagram Side panel Rear panel Column Breakdown Parts Column Parts List 80-1 92V2 Electrical Box Breakdown & Parts List Headstock Breakdown Headstock Parts List Description Chip Guard Breakdown & Parts List Labels Breakdown & Parts List Model G0704 Mfg. Since 08/11 Comments Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC Warranty and Returns