Labels Breakdown & Parts List | Grizzly G0759 manual

Labels Breakdown & Parts List

	310	302
	310	301
		301

309

308

307

REF	PART #	DESCRIPTION

301	P0704301	READ MANUAL LABEL
302	P0704302	SAFETY GLASSES LABEL
303	P0704303	MACHINE ID LABEL
304	P0704304	HIGH/LOW SPEED LABEL
305	P0704305	PUTTY TOUCH-UP PAINT

303

304

305

306

REF	PART #	DESCRIPTION

306	P0704306	MODEL NUMBER LABEL
307	P0704307	GREEN TOUCH-UP PAINT
308	P0704308	CUTTER WARNING LABEL
309	P0704309	ENTANGLEMENT LABEL
310	P0704310	AVOID OVERHEATING LABEL

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

Model G0704 (Mfg. Since 08/11)

-53-

Image 65

Grizzly G0759 owner manual Labels Breakdown & Parts List

Contents

Model G0759 Machine Data Sheet Table Info Column & Stand Description Electrical Box Headstock Description Chip Guard Labels Model G0704 MILL/DRILL with Stand Page Table of Contents Machine Description IntroductionManual Accuracy Contact Info Identification G0704 electronic controls identification Electronic Controls Identification Model G0704 DRILL/MILL with Stand 50 2250 RPM Accessories Included Safety Instructions for Machinery Safety ChILdREN & BYsTANdERs. Keepchildrenand Maintain Power CORds. When disconnect Additional Safety for Mill/Drills Power Supply 50 ft Minimum Gauge Size 16 AWG Description Qty Needed for SetupUnpacking Not Shown Contents QtyInventory Basic steps for removing rust preventative CleanupBefore cleaning, gather the following Site Considerations Weight Load Moving & Placing Machine Example of a direct mount setup Bolting to Concrete Floors Mounting to Shop Floor To install the drill chuck onto the arbor AssemblyDrill Chuck Arbor To assemble your machine Connecting Power Power Connection To test run and break-in the spindle bearings Test Run & Spindle Break-in Operation Overview Operations Speed Range Selector Knob Selects low range Basic Controls Digital readout unit controls Model G0704 Mfg. Since 08/11 To use the digital readout Digital Readout Unit To determine the needed spindle speed Calculating Spindle Speed To set the spindle speed Spindle Speed Direction Spindle Height Controls Changing Spindle Position Using Quill Feed Levers Drill Chuck To install the drill chuck and arbor To remove the collet To install the toolingLoading Tooling To tilt the headstock to the left or right Headstock Travel Axis and RotationTo raise or lower the headstock Cross Feed Table TravelLongitudinal Feed G5684-R-8 Vertical Collet Rack H8179H8177-Worktable with Angle H5685-4Rotary Table G9322-Boring Head Combo SetG8683Z-Mini Shop Fox Mobile Base G5758-Tilt x Model G9512 T-Slot Nuts Lubrication MaintenanceSchedule To lubricate the leadscrews Tools Needed Qty Handwheel gears Troubleshooting Service Symptom Possible Cause Possible Solution Gibs To adjust the table gibsTo adjust the headstock gibs To adjust the Y-axis leadscrew nut Battery ReplacementTo adjust the X-axis leadscrew To replace the digital readout unit battery To inspect and replace the motor brushes Motor Service Wiring Safety Instructions Wiring Wiring Diagram Side panel Rear panel Column Breakdown Parts Column Parts List 80-1 92V2 Electrical Box Breakdown & Parts List Headstock Breakdown Headstock Parts List Description Chip Guard Breakdown & Parts List Labels Breakdown & Parts List Model G0704 Mfg. Since 08/11 Comments Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC Warranty and Returns