Spindle Height Controls | Grizzly G0759 manual

Spindle Height

Controls

The spindle height is controlled by the quill feed lever and the fine feed knob.

	Fine Feed	Quill Feed
	Knob	Lever
	Spindle
	Height
	Scale
	Quill	Fine Feed
	lock	Fine Feed
	lock	Lock
	lever	Lock
	lever	Knob
		Knob

Figure 27. Spindle controls.

Changing Spindle Position Using Quill Feed Levers

1.Unlock the quill lock lever and loosen the fine feed lock knob.

2.Pull down on any of the coarse downfeed levers to adjust the vertical position of the spindle. Observe the spindle height scale or digital readout to monitor movement in inches or millimeters.

Tip: Milling with the spindle fully extended can cause tool chatter. For maximum spindle rigidity when milling, it is better to keep the spindle retracted into the headstock as far as possible with the spindle lock and the downfeed selector knob tightened.

Changing Spindle Position Using Fine Feed Knob

1.Unlock the quill lock lever and tighten the fine feed lock knob.

2.Rotate the fine feed knob to lower or raise the spindle in small increments. Observe the scale on the knob or the digital readout to monitor movement in thousandths of an inch (Figure 28).

	Fine Feed	Fine Feed	Quill Feed
	Scale	Lock	Quill Feed
	Scale	Lock	Lever
		Knob	Lever
		Knob
	Quill
	lock	Fine Feed
	lever	Fine Feed
	lever	Knob
		Knob

Figure 28. Fine spindle feed controls.

3.Tighten the quill lock lever to hold the spindle in a particular position if you choose.

Tip: Milling with the spindle fully extended can cause tool chatter. For maximum spindle rigidity when milling, it is better to keep the spindle retracted into the headstock as far as possible with the quill lock lever tightened, and the fine feed knob tightened.

-28-	Model G0704 (Mfg. Since 08/11)

Image 40

Grizzly G0759 owner manual Spindle Height Controls, Changing Spindle Position Using Quill Feed Levers

Contents

Model G0759 Machine Data Sheet Table Info Column & Stand Description Electrical Box Headstock Description Chip Guard Labels Model G0704 MILL/DRILL with Stand Page Table of Contents Manual Accuracy Contact Info IntroductionMachine Description Identification Electronic Controls Identification G0704 electronic controls identification Model G0704 DRILL/MILL with Stand 50 2250 RPM Accessories Included Safety Safety Instructions for Machinery Maintain Power CORds. When disconnect ChILdREN & BYsTANdERs. Keepchildrenand Additional Safety for Mill/Drills Power Supply Minimum Gauge Size 16 AWG 50 ft Unpacking Needed for SetupDescription Qty Inventory Contents QtyNot Shown Before cleaning, gather the following CleanupBasic steps for removing rust preventative Weight Load Site Considerations Example of a direct mount setup Moving & Placing Machine Mounting to Shop Floor Bolting to Concrete Floors Assembly To install the drill chuck onto the arborDrill Chuck Arbor To assemble your machine Power Connection Connecting Power Test Run & Spindle Break-in To test run and break-in the spindle bearings Operations Operation Overview Basic Controls Speed Range Selector Knob Selects low range Digital readout unit controls Model G0704 Mfg. Since 08/11 Digital Readout Unit To use the digital readout Calculating Spindle Speed To determine the needed spindle speed Spindle Speed Direction To set the spindle speed Changing Spindle Position Using Quill Feed Levers Spindle Height Controls To install the drill chuck and arbor Drill Chuck Loading Tooling To install the toolingTo remove the collet To raise or lower the headstock Headstock Travel Axis and RotationTo tilt the headstock to the left or right Longitudinal Feed Table TravelCross Feed H8177-Worktable with Angle H8179G5684-R-8 Vertical Collet Rack G8683Z-Mini Shop Fox Mobile Base G9322-Boring Head Combo SetH5685-4Rotary Table Model G9512 T-Slot Nuts G5758-Tilt x Schedule MaintenanceLubrication Tools Needed Qty To lubricate the leadscrews Handwheel gears Service Troubleshooting Symptom Possible Cause Possible Solution To adjust the headstock gibs To adjust the table gibsGibs Battery Replacement To adjust the Y-axis leadscrew nutTo adjust the X-axis leadscrew To replace the digital readout unit battery Motor Service To inspect and replace the motor brushes Wiring Wiring Safety Instructions Wiring Diagram Rear panel Side panel Parts Column Breakdown Column Parts List Electrical Box Breakdown & Parts List 80-1 92V2 Headstock Breakdown Headstock Parts List Chip Guard Breakdown & Parts List Description Labels Breakdown & Parts List Model G0704 Mfg. Since 08/11 Warranty Card Comments Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WA Warranty and Returns