Grizzly G97030 owner manual Power Feed Controls, GZZgidFigures 77-78VcYiZdaadlc\YZhXge

Power Feed

Dc i]^h aVi]Z! Wdi] i]Z XVgg^V\Z VcY Xgdhh ha^YZ ]VkZ edlZg [ZZY XVeVW^a^in l]Zc Zc\V\ZY l^i] i]Z [ZZYgdY# I]Z gViZ i]Vi i]ZhZ XdbedcZcih bdkZ[ZZYgViZ^hXdcigdaaZYl^i]i]Z]ZVYhidX` VcYfj^X`X]Vc\Z\ZVgWdmXdcigdah#

;ZZYgViZVcYhe^cYaZheZZYbjhiWZXdch^YZgZY id\Zi]Zg# I]Z hdjgXZh ndj jhZ id YZiZgb^cZ i]Z dei^bjbhe^cYaZheZZY[dgVcdeZgVi^dcl^aaVahd egdk^YZ i]Z dei^bVa [ZZY gViZ id jhZ l^i] i]Vi he^cYaZheZZY#

D[iZc!i]ZZmeZg^ZcXZYbVX]^c^hil^aajhZi]Z[ZZYh VcYheZZYh\^kZc^ci]Z^ggZ[ZgZcXZX]VgihdglZW XVaXjaVidgh Vh V hiVgi^c\ ed^ci! i]Zc bV`Z b^cdg VY_jhibZcihidi]Z[ZZYgViZVcYhdbZi^bZhi]Z he^cYaZheZZYidVX]^ZkZi]ZWZhigZhjaih#

I]Z XVgg^V\Z XVc VaiZgcViZan WZ Yg^kZc Wn i]Z aZVYhXgZl[dgi]gZVY^c\deZgVi^dch#=dlZkZg!i]^h hZXi^dc XdkZgh i]Z jhZ d[ i]Z edlZg [ZZY dei^dc [dgi]ZXVgg^V\ZVcYXgdhhha^YZXdbedcZcihl]Zc i]ZnVgZZc\V\ZYl^i]i]Z[ZZYgdY[dgcdc"i]gZVY" ^c\deZgVi^dch#IdaZVgc]dlidedlZgi]ZXVgg^V\Z [dg i]gZVY^c\ deZgVi^dch! gZ[Zg id Threading dc Page 56#

NOTICE

Even though there is a lock-out device in the apron to prevent the feed control knob and the halfnut lever from being engaged at the same time, this device could break with enough force. Attempting to engage feed control knob and the halfnut lever at the same time could cause severe lathe dam- age and will void the warranty.

If you attempt to use the controls on the headstock above the control panel to make changes when the spindle is rotating, the headstock gearing will suffer damage! ALWAYS make sure the spindle is com- pletely stopped BEFORE using the head- stock controls to make changes.

BdYZa<.,(%$<.,(&B[\#H^cXZ.$%%

Power Feed Controls

GZ[ZgidFigures 77–78VcYi]Z[daadl^c\YZhXg^e"

i^dch id WZXdbZ [Vb^a^Vg l^i] i]Z adXVi^dch VcY

[jcXi^dchd[i]ZXdcigdahndjl^aajhZidhZijei]Z

XdggZXiedlZg[ZZY[dgndjgdeZgVi^dc#

Important: Before engaging power feed, make sure the carriage and slide locks are loose to pre- vent damage to these components.

Note: Before using power feed, you may have to re-configure the change gears, depending on how they are set up. Refer to Change Gears on Page 57 for detailed instructions.

6 7

8 9

:

;

Figure 77.EdlZg[ZZYXdcigdahdc]ZVYhidX`

VcYfj^X`X]Vc\Z\ZVgWdm#

A.Headstock Feed Direction Knob: 8]Vc\Zh i]Z gdiVi^dc d[ i]Z [ZZYgdY id X]Vc\Z i]Z Y^gZXi^dcd[XVgg^V\ZigVkZa#

B.Quick Change Knob A–C: 8]Vc\Zh i]Z heZZY d[ edlZg igVch[Zg [gdb i]Z ]ZVYhidX` \ZVghidi]ZadlZgfj^X`X]Vc\Z\ZVgh#

"*("