Hearth and Home Technologies 6000BE specification

Step 5. Installing the Optional Heat-Zone Kit

NOTE: There must be NO INSULATION or other com- bustibles inside the framed firestop opening.

Step 6. The Gas Control Systems

!WARNING: THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

HEAT-ZONE

ATTACHES

HERE

Figure 32.

Two types of gas control systems are used with these models: Standing Pilot Ignition and Intermittent Pilot Ignition (IPI).

Standing Pilot Ignition System

This system includes millivolt control valve, standing pilot, thermopile/thermocouple flame sensor, and piezo ignitor.

!WARNING: 110-120 VAC MUST NEVER BE CONNECTED TO A CONTROL VALVE IN A MILLIVOLT SYSTEM.

Intermittent Pilot Ignition (IPI) System

This system includes a 3V control valve, electronic module and intermittent pilot.

!WARNING: CONTINUOUS 110-120 VAC SER-

VICE MUST BE WIRED DIRECTLY TO THE FIRE- PLACE JUNCTION BOX.

1. Remove the knockout from the fireplace and discard it
(see Figure 32).	STANDING PILOT
2. Center the duct collar around the exposed hole and at-	STANDING PILOT
2. Center the duct collar around the exposed hole and at-
tach it to the fireplace with 3 screws. NOTE: Do this BE-
FORE final positioning of the fireplace.
3. Determine the location for the air register/fan housing
assembly.
Reference the Heat-Zone kit instructions for the remaining
installation steps.
	INTERMITTENT PILOT IGNITION
	FLAME SENSOR
	ROD
	Figure 33. Gas Controls Systems
Hearth & Home Technologies • 6000BE, 6000BE-IPI • 2024-900 Rev. G • 11/05		27

Image 27

Hearth and Home Technologies 6000BE owner manual Installing the Optional Heat-Zone Kit Gas Control Systems

Contents

What to do if you smell gas Installation and Operation Safety and Warning Information Table of Contents Log Set Assembly Service Parts GLA-750TR Service Parts List 6000BE, 6000BE-IPI Intermittent Pilot Ignition Valve Assembly Standing Pilot Ignition 6000BE Certification High Altitude InstallationsInstallation Codes Appliance Certification Pre-install Preparation Introducing the Hearth & Home Technologies Gas FireplacesANY Such Action MAY Possibly Cause a Fire Hazard GAS Line Access Diagram of the 6000BE, 6000BE-IPI Constructing the Fireplace Chase Locating the FireplaceClearance Requirements Framing the Fireplace Framing Dimensions DVP90ST Identifying Vent Components Installing the Vent SystemVent System Approvals Tems or Components MAY be Used Flue Restrictor Instructions Vertical VentingMAX .4 M Straight Up Vertical Venting Chart Venting with One 90 Elbow Venting with ONE 1 90 Elbow Venting with Two 90 Elbows Venting with TWO 2 90 o Elbows Venting with three 90 elbows Venting with Three 3 90 Elbows + V 1 FT + H 1 FT Installing Vent Components Above the First 900 Elbow in the Venting System To Install the Heat ShieldInstall Support Brackets Continue Adding Vent Components 12 Hole and Vent Pipe Vent Termination Attic FirestopHorizontal Termination Alcove Applications Service Proper Positioning Leveling and Securing of a Fireplace Positioning, Leveling, and Securing the Fireplace Intermittent Pilot Ignition IPI System Installing the Optional Heat-Zone Kit Gas Control SystemsVice Must be Wired Directly to the FIRE- Place Junction BOX Standing Pilot Ignition System Check for GAS Leaks Gas Supply LineGas Pressure Requirements Pressure Natural Gas Propane Wall Switch Wiring the FireplaceFor Standing Pilot Ignition Wiring Appliance Requirements Optional Accessories BRN Operation using Battery Power Installing Trim, Logs, and Ember Material Installing the TrimFinishing Positioning the Logs Follow these steps Cover Ports Shutter Settings Glass Assembly Placing the Ember Material6000BE Tempered 6000BE-IPI Tempered Double-check for faulty components Cold Climate SwitchBefore Lighting the Fireplace Important Turn OFF the GAS Before Servicing Your Fireplace After the InstallationFireplace Maintenance Lighting the Fireplace